Search Documents

By Hughes DC

Coal development in New South Wales can involve a complex series of government approvals, a requirement that results from the coincidence of many development sites with environmentally sensitive areas. The concept of network analysis is applied to the pre- development regulatory procedures leading up to the grant of a coal lease. The network facilitates a quantitative and qualitative analysis of activity schedules relating to pre- requisite statutory approvals. The sequencing of activities (with clear start and finish nodes, identification of sensitivities and time estimates for completion of each phase of the network) provides government and industry with an effective planning tool.

Jan 1, 1983

Underground mechanized excavation in New Zealand has become more commonplace in civil and mining applications during the last three years. At one stage up to seven Dosco Road- header machines were being used on different projects around the country. The Huntly West Mine Drifts inclined at one in four were by far the most severe grade conditions that the machines were subjected to; however, other operations posed their own particular problems for the machines. Two major interrelated factors became evident as soon as the machines commenced at Huntly. These were traction problems on the grade and control of water, particularly on the invert.

Jan 1, 1978

By Aziz NI, Beafi EY

In designing for a highly productive new mine during the present declining coal market, a very detailed ò planning is necessary. Attitudes of both management and coal operators may have to be changed, with more initial participation by the unions, governmental agencies, and the coal owners. A considerable number of Australian mines are remote from labour source and this trend is likely to increase particularly in the state of Queensland. Consequently such 'mines must be developed on the basis of the future technological and social changes in order to minimise both the capital and operating costs.

Jan 1, 1988

By Canterford JH, Ritcey GM

With the development of new technology and materials of construction, chloride-based hydrometallurgical routes have gained accept- ance as a viable alternative to sulphate-based routes. A number of commercial and pilot plants built and operated over the last decade have provided invaluable experience and con- fidence in their use. Chloride hydrometal- lurgy, with or without pyrometallurgical pre- treatment, is particularly attractive for pro- cessing complex Cu/Pb/Zn/Ag concentrates, nickel mattes and chalcopyrite concentrates. This review outlines recent developments, dis- cusses advantages, as well as indicating some of the problems still to be solved.

Jan 1, 1984

By J C. Diaz, C R. Scherpenisse

Blasting represents one of the most relevant unit operations in the process of mineral extraction. The final objective of this operation is that of obtaining an adequate final fragment size distribution such that the combined costs of drilling, blasting, excavation and transport, and crushing/grinding, are minimised, while at the same time producing the minimum possible level of damage to the surrounding rock mass. The strong influence that drilling and blasting has over the subsequent processes involved in the operational cycle makes it imminently desirable to have access to experience and technology which make possible the evaluation and optimisation of this unit operation. The correct use of vibration monitoring techniques offers a number of benefits in terms of their ability to examine any blasting process in detail. In effect, the measurement of particle velocity levels that result from the detonation of each explosive charge offers a means by which it is possible to measure relative efficiency of each charge, interactions (productive and counterproductive) between adjacent charges, and a definitive indication of general performance of any given blast design and its implementation. In this way the monitoring of blast vibrations in rock due to the blast event, can be used as a diagnostic tool, given that the correct interpretation of the vibration traces allows the determination of the level of interaction between the design and operational variables of the blast event. This makes it possible to evaluate, for example, the presence of out of sequence detonations, statistical scatter in the detonation times of pyrotechnic delay detonators, deficient detonation of charges, instantaneous detonation of charges and sympathetic detonation of charges, as well as the general of vibration levels in terms of peak particle velocity, acceleration, and displacement. Another important use of such data is in the construction of a database relating vibration levels to charge weight, hole diameter, and distance, for any given rock type, enables the calibration of predictive vibration models which in turn make it possible to predict the damaging effects of blasting. Knowledge of both the vibration levels induced, combined with quantitative measures of the geomechanical competence of a rock mass make it possible to estimate the probability of producing blast induced damage. The high levels of vibration generated by some blast events may damage the rock mass, producing new fractures or extending and dilating existing fractures. The vibration in this context may be considered as a dynamic stress provoking strain in the rock mass. This paper describes the application of the vibration monitoring technique, particularly in the underground mining environment, and its importance in diagnosis, modelling, control, and optimisation of the development blasting process. The potential of the technique is assessed in the context of achieving substantial techno-economic improvements development blasting results, increasing output whilst minimising the operational costs of the mining process.

Jan 1, 1999

By Kagl J, Publlier M, Nekitel S, Arumba J, Rangin C, Mosusu N

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By R Yong, A McEwan, D G. Miljak, D Milinkovic, A Curtain, P J. Coghill, R Stefulj, B Lovric, G Roberts

The CSIRO has pioneered the development and use of certain classes of magnetic resonance (MR) for mining applications. The MR technique is a radio frequency-based spectroscopy that provides highly quantitative measurement of selected ore minerals. MR has many inherent advantages for bulk sensing in mining applications, including deep sensing penetration into most bulk ores with the use of non-contact sensors that are robust and tolerant of demanding mine conditions. The highly discriminating nature of the technique also provides the very desirable attribute of robust and simple calibration, that can often be performed prior to sensor installation. Rapid sensing (within seconds) at very low grade (few hundred ppm Cu) has been demonstrated, as well as sensing at high tonnage rate. Besides sorting applications, MR may also be applied to preconcentration applications involving very large volume sensing including: (i) haul truck sensing using portal arrangements, where truck destination assignment may be dynamically determined based on the truck grade, (ii) in-pit gantries used for loading trucks that may similarly be equipped with sensors for truck assignment and (iii) deep mine bench sensing, recently progressed through a CRC ORE project, where local bench grade is determined at the few-metre lateral scale and at depth prior to blasting, to aid selective blasting and ore extraction. MR sensor prototypes have been developed for each of these applications and have been tested in laboratory or limited field conditions. To inform the value proposition for truck or bench sensing, initial analysis of truck assignment improvement based on an analysis of in-situ mine bench grade has been performed for a porphyry style deposit. The prototype sensors, preliminary results and future technology development and objectives will be described.

Nov 10, 2020

The unique characteristics of the Target orebody and modernistic approach to mining present significant challenges and a concomitant high potential for new opportunities. The break-away from the traditional labour intensive mining methods improves both safety and productivity significantly. The intention of the paper is to illustrate the application of well known mining methods to the particular requirements of a complex orebody at depth. The evolutionary process followed to establish the final mining method design provides insight behind the finished product, and the modern approach to the planning and service principles equips the reader with a suite of mining engineering ideas.

Jan 1, 2000

The paper discusses the characteristics of Be-zymianny activity during the last 2500 years. Three periods of increased activity have been identified which are the eruptive cycles lasting for 100-400 yrs. The periods of high activity fall on the fol-lowing time intervals: 2400-1700 yrs ago, 1350-1000 yrs ago and from 1955 ixp to the present time. The 1955-1956 catastrophic eruption after a long period of repose (about 900-1000 yrs) opened a new cycle of activity of the volcano which is continuing to-day. Several decades are distinguished in activity which differ in character and intensity of eruptions.

Jan 1, 1990

The locality from where these specimens come is distant about 12 miles due south from the township of Bingara New South Wales, and is known locally as Carney's Reef, Barrack's Creek, Top Bingara. The formation traverses the western side of a serpentine spur from the main range, which runs through the country from the other side of Tamworth to Inverell, in the New England District. It has a due north and south trend, with an easterly underlay slightly out of the vertical. The formation has been opened up at different points for a distance of over two miles, and each place showing gold in the stone, and no place more than three to four chlins apart, the whole distance along the line of Reef being leased. The formation varies in thickness, the smallest being about 1 foot and the widest about 10 feet. The following is a list of properties, and description of work done on them at present. First south, and about one and a half miles from Hanion Brothers' old BalIarat claim due north, Court and patty hold a tenacre lease. The formation outcrops near the south boundary, and gold is obtainable in the stone. In the centre of the lease a costeen pit has cut the capping, which shows gold, and about two chains from the north boundary another one cuts the capping, also showing gold. The reef averages, where exposed on this property, 3 feet wide.

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

As a result of cheap Maui gas and plentiful hydro-electricity, over the past few decades New Zealand has enjoyed some of the cheapest energy of any OECD country. The situation is changing; at best we are facing some radical changes in energy use, at worst we are facing a crisis resulting from the following:   Cause 1: Maui gas will be exhausted by 2012. Distorted pricing and supply contracts; resulted in Huntly Power Station, a coal mine mouth generator running on 70 per cent Maui gas until very recently!   Cause 2: Investment in new generating capacity (and transmission) is woefully inadequate; as a result hydro lake levels are being continually pushed to the limits.   Cause 3: Distorted thinking is everywhere, for example; æWe will find more cheap gasÆ. æGas is clean û coal is dirtyÆ. Hot air  û ægreen alternatives such as wind generation will save usÆ. æNo NuclearÆ. The outcomes of the distorted thinking will be price increases, then shortages (there is nothing like "black-outs" to focus national thinking) and finally recession.   But what can NZ do? - Mine Coal. Coal jump-started the industrial revolution, it can provide the transition to post-gas and oil. NZ has the second highest reserves of coal per capita in the world, yet we use less that any other country with significant coal reserves. Our exports of our best coal have increased threefold, yet out own consumption has remained static at about 1-1.5 Mtpa for the last 30 years. Our coal is NZ owned and inexpensive relative to other energy sources, even allowing for infrastructure and environmental costs.   What can we do? We as mining professionals can promote informed responsible development and investment in the country's mining and energy business. We can galvanise public opinion on issues such as æunbundlingÆ our entire energy chain from mine-to generator-through transmission, even if the nuclear issue has to wait! With oil above US$70/bbl substitution is feasible. For individuals, there is always solar!

Jan 1, 2006

By Jankola W. A, Delong O. J

Historically, the silica content of zinc concentrates treated at Cominco's Trail Operations has been low. Silica in the roaster calcine seldom exceeded 1.5 per cent because of the low silica content of concentrate from Cominco's Pine Point mine. With the shutdown of Pine Point, alternate sources of concentrate were required and it was anticipated that calcines containing greater than two per cent silica (with excursions above three per cent) would have to be treated. Previous experience indicated that the existing leaching circuit could not tolerate such high levels. Therefore, a research program was undertaken to identify the key factors affecting silica precipitation; to compare different process alternatives; and to make recommendations for modifications to the existing plant. A project to modify and upgrade the leaching circuit has now been completed. Calcines with higher silica contents are successfully treated, but the upper limit of the circuit is unknown. The results of the research work will be discussed and the new leaching plant will be described. Recent operating results will also be presented.

Jan 1, 1993

By X Hu, J Björkvall, L Sundqvist Ökvist

The metal production industry is a significant contributor to global CO2 emissions due to the use of fossil fuels such as coal and coke. To mitigate these emissions and meet climate goals, innovative and sustainable technologies are required. Molten salt electrolysis is a promising technology that directly produces metals from their precursor sulfides or oxides using electricity. When combined with renewable electricity and an inert anode, the electrolysis process can be carbon neutral. This paper presents the results of two pilot-scale studies on the electrolytic reduction of metal oxides and sulfides in molten salts. The first study focuses on the electrolytic reduction of chalcopyrite in molten NaCl-KCl salt. The results demonstrate that in situ separation of copper, iron, and sulfur is possible, enabling the extraction of all valuable elements without CO2 emissions. Furthermore, the findings underscore the capability to eliminate impurities like zinc, antimony, arsenic, and mercury from the electrolysis product. The second study investigates the electrolytic reduction of pure/synthetic chemicals of wüstite, hematite, and magnetite, as well as a magnetite-type iron ore in molten NaOH salt. The findings reveal a stepwise reduction of iron oxides from high valence to low valence, ultimately leading to the production of metallic iron electrolytically. Notably, this study underscores the challenges associated with the selection of an economically viable and durable inert anode material for efficient oxygen generation. These results indicate that molten salt electrolysis provides a sustainable and green route for base metal production. The use of this technology has the potential to significantly reduce CO2 emissions in the metal production industry, contributing to achieving climate goals.

Jun 19, 2024

In most States of Australia it is a legislative requirement for underground mines to have a separate means of egress from the normal means of ingress to permit the safe evacuation of workers to the surface in event of an emergency. Such egress may be in the form of a ladderway equipped shaft/underlie or trafficable incline/decline. Additionally, there is a general requirement to have one or more airways, separate to the main shaft or other principal entrance of an underground mine, extending to the lowest level to permit ventilation to all parts of the mine. Fulfilling these requirement is difficult in the development phase of a mine when access underground is achievable by only a shaft or decline in the process by being sunk. What is frequently practiced in Australia is for production to then commence, sometimes in association with continuing development, in the same configuration without the establishment of this separate method of egress to the surface nor additional airway/s with reliance on refuge chambers to cater for back up in any emergency. Not only, could this jeopardise the health and safety of workers in case of an underground emergency it could be construed as a statutory breach of legislation. While recognising that refuge chambers are often used throughout underground operations nowadays their equipping and the criteria for their location needs to be bought into focus. This presentation discusses how such legislative requirement can be met alongside the use and appropriateness of refuge chambers.

Jan 1, 1998

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

Mechanical and electrical (M&E) systems in road tunnels are constrained by the traffic envelope and the construction profile. Whilst these spatial constraints are often ælocked inÆ early in the design process, the detailed M&E design continues for some considerable time after key civil engineering issues have been resolved. Ventilation design criteria for both normal and emergency operation often involves considerable negotiation with a wide range of stakeholders. Final system performance and spatial requirements are only finally resolved when suppliers are selected following the tender process. Lighting design is dependent upon a wide range of factors including tunnel lining materials and associated colours as well as agreed maintenance regimes. Cabling systems can only be developed when the general arrangement for power distribution is agreed and a system of substation, switchrooms and equipment rooms is in place. Many other systems such as fire protection and communications facilities fill the available space beyond the traffic envelope, where physical, structural and æsight lineÆ requirements must all be accommodated. The more co-ordinated civil engineering and M&E design is and the earlier the process starts the better the outcomes for all parties.

Jan 1, 1999

Studies of human relations are being made by a team of psychologists within management and in the community of Kambalda as a whole. Some of the first results are discussed with reference to extensions required in management when it also has to run a mining town. Implications are noted for town planning policies of the attitudes and preferences of the population with regard to housing and to other major planning areas. Some of the theoretical and practical difficulties of 'planning the human ecology' are outlined.

Jan 1, 1973