Search Documents

That gold will dissolve in sodium hyposlphite solutions is known from the lixiviation of silver and gold ores.The gold will dissolve only in small quantities. According to Stetefeldt, if gold leaf is treated for a time with sodium hyposlllphite solutions of varying strengths solution takes place in every instance, the deviation in quantity being very slight.In order to form hyposulphite double-salts, the gold must become oxidised, the oxygen being derived from the air absorbed by the solution. Consequently, it is the quantity of free oxygen in the solution by, which the reaction is determined, as for one equivalent of gold dissolved one equivalent of caustic soda is set free.

Jan 1, 1901

By Waddell S

A new procedure has been developed for the direct determination of metals loaded on activated carbon. It involves preparation of a suspension of the powdered carbon in water, followed by direct sampling of the suspension with a micropipette,and analyses by atomic absorption spectroscopy using carbon rod atomization. Advantages of the method include the simplicity of sample preparation and the ability to provide a complete metal analysis in 1 - 2 hours. This enables carbon-in-pulp operators to respond quickly to changes in plant efficiency arising from carbon fouling. The successful application of the method has been demonstrated for gold, copper, nickel and iron. Other elements to be surveyed include calcium, magnesium and silicon.

Jan 1, 1984

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000

Several years and millions of dollars later, the mining and extractive industries have now started to receive and implement industry based standards aimed at achieving better performance and output from the employee. IFAP in conjunction with the mining and quarrying industry has developed a range of training courses aimed at achieving the benefits that can be gleaned from application of these standards. The establishment of a career path and appropriate training packages for personnel involved in the handling and use of explosives provides industry with a training system that previously did not exist. The opportunity to receive quality training based on industry standards and aimed at achieving industry goals will now enable the industry to optimise itÆs explosives applications.

Jan 1, 1999

Uniaxial compressive strength and Young's modulus values measured in the laboratory on NX diamond drill cores were examined statistically to bring out any significant differences between different locations in the mine which might require special treatment in subsequent photoelastic analyses of the mine layout. Correlations were sought between the strength and modulus and various other features of the rock. The estimated mineral content of the core correlated with the modulus of the core, but the range of modulus values was too limited to show any strong correlation with compressive strength.Strength in the vertical direction was found to be significantly higher than in the horizontal direction and the same pattern was followed by the moduli, but was less pronounced. It was concluded that, whilst the modulus variations were significant, they would not invalidate any photoelastic studies.

Jan 1, 1969

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By A E. A Northcote

The drive to maximise performance, reduce maintenance times, improve safety of operation and maintenance on mining equipment while keeping both operational and capital costs down has provided good nourishment to the creative thinking of designers of skip loading facilities for hoisting systems. Early systems were as simple as manual loading which evolved into a surge bin feeding a skip through a chute finally maturing into a measuring flask discharging into a chute to feed the skip and more recently high capacity skip feed conveyors. This paper will compare the concepts of the skip loading flask and the skip loading conveyor systems over a range of winding distances and hoisted tonnages. The comparison will draw on actual installations and review operational, maintenance and safety. An order of magnitude capital cost estimate will be used to complete the financial comparison. This will enable the reader to understand the concepts and costs and assist in selecting the appropriate skip loading system.

Mar 21, 2011

In-stope long hole drilling (face parallel drilling) is a new technology currently being applied to shallow dipping (

Jan 1, 2003

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By Mosusu N

Geothermal anomalies of different types occur within distinct geological/structural settings in Papua New Guinea. According to R.F. Herring, geothermal occurrences in Papua New Guinea can be classified into two types, those related to vulcanism (Lihir, Rabaul and other series of islands along the volcanic arc) and those resulting from a regional heat flow probably caused by radiogenic sources, for instance those in the Wau/Bulolo area. The manifestation of this potential source of energy generally coincides with either converging or diverging tectonic plate boundaries. Previous inventories on thermal waters were carried out by vulcanologists from the Rabaul Observatory in the early 1960s. However, these studies rarely included chemical analyses of water and gas emissions and the investigations were carried out in an ad hoc manner, generally as a secondary activity. The most recent investigation on thermal waters was conducted on Lihir Island in connection with the development of the open pit gold mine. These studies included detailed exploratory drilling to a maximum depth of 730 m, and a water chemistry isotopic sampling and analysis programme. The hydrothermal waters were not considered as an energy source but as a hazard during the development stage of the mine. Nevertheless, the geothermal anomaly observed at Lihir includes hot springs emerging along the coastal zones with temperatures that approach 100¦C, steam, and thermal borehole waters with temperatures that exceed 200¦C. Chemical analysis results of thermal fluids from Rabaul, Talasea and other areas in Papua New Guinea generally show high total dissolved solids and low pH. In contrast, recent results from the deepest and hottest thermal source at Lihir shows a neutral pH, a Na-CI-SO4 composition and temperatures above 200¦C. Despite the concentration of chloride being similar to that of sea water, other chemical results and stable hydrogen and oxygen isotopic compositions of thermal fluids imply the source to be mixture of local meteoric water and deep thermal water rather than sea water. Results of geothermal modelling suggests that the total geothermal uptlow is equivalent to 54 MW.

Jan 1, 1997

By N Vagias, R Shaw, M Coghill, W Easman

Rio Tinto Technology and the Rio Tinto Foundation for a Sustainable Minerals Industry have funded the development of a practical floating module that can reduce water losses through evaporation from water dams at mining and mineral processing facilities by about 75 per cent. The modules, which are also suitable for use by farmers and communities, were designed for easy deployment, to allow the water to æbreatheÆ, harvest rainfall and resist wind speeds of more than 100 km/h. A large-scale demonstration trial will be conducted at the Northparkes Mine, located near Parkes (New South Wales, Australia). The objective of the trial is to demonstrate to Rio Tinto business units, community, farming and government groups the moduleÆs operating costs and water saving potential.

Jan 1, 2006

By Chen J, Sun ZY

The present paper gives the design of a new HGMS for magnetic separation of sulphides. The main characteristics of this HGMS are using iron-cladding saddle-shaped magnetic coil for instead of the ordinary magnet, and combining reciprocal-linear motion with vibration to actuate the separation box, and the magnetic field intensity is high up to 2T as well. For improving the magnet system design, a modified finite element method is used to calculate the distribution of magnetic field intensity of separation space of the magnetic coil, and accordingly the calculation results the magnetic leakage coefficient can be determined easily, thus designers apart from the empirical way. KEYWORDS: HGMS, reciprocal motion and vibration, finte element method, saddle-shaped coil.

Jan 1, 1993

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

Key incompatible element ratios for metabasalts from the Early Permian Croisilles and Patuki Volcanics, South Island, New Zealand, provide constraints on the tectonic environment in which their precursor ophiolitic protolith formed. Two geochemically distinct metabasalt suites are recognised among both the Croisilles and Patuki rocks. Metabasalts from one suite exhibit the geochemical signatures of depleted tholeiites from oceanic spreading ridges (N-type MORB) or spreading centres in evolved back-arc basins. These N-type tholeiites show high Zr/Nb ratios (Zr/Nb = 37-62) and are depleted in light rare earth elements (LREE)((La/Y)N

Jan 1, 1987

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

The earth is a planet limited in size and limited in total resources. For the forseeable future, it is the only available habitat for mankind. Therefore, it follows that the more we know about our planet the better we can utilize its space and its resources for our well-being now and in the future. But, to accomplish this, we need reliable basic information. Geosciences provide such information. Recently, Dr. M. King Hubbert took note of the important effect of the geosciences on society, on how we think, and how we live. In the first century of modern geology, 1780- 1880, the influence of geology was primarily on how we think, i.e. changing our concept of the earth from one with a short catastrophic history to one that developed gradually over enormous spans of time. In the second century, 1880-1980, the emphasis was on how we live, on expanding the knowledge base so that we could more easily find and utilize the earth's resources. Now, in the third century, i.e. from 1980 towards the year 2000 and beyond, we should concentrate on both how we think and how we live; i.e. how we can better estimate potential global' resources and how we can manage these resources for maximum benefit to mankind. Like other sciences, the geosciences build upon what has already been done. Progress is achieved by using the thoughts, measurements, and observations of past workers, adding to these the insights from new experiments and from new concepts. Geology has its own methodology and approaches; but more than most sciences, it calls also upon the tools of physics, chemistry, mathematics, engineering, and biology to help solve its problems. Today's increasing population, increasing industrialization, and increasing complexity of modern society demand more detailed geoscience information so as to better use the land, reduce geological hazards, provide an inventory of resources, facilitate waste disposal, and prepare for long-term effects such as changes in climate and sea level.

Jan 1, 1986