Search Documents

By A Robertson

Australia has been slow in adopting the use of underground space as a part of our urban planning process. Australia has one of the highest levels of tunnel advance per capita per annum in the world, yet the use of underground space in our cities appears difficult for our planners and politicians to comprehend, not withstanding the general availability of good quality rock and contractor expertise in Australia. However, the lack of space in our urban areas is being highlighted as our major cities expand outwards and people and businesses gravitate towards city centres. Typical potential underground space uses include car parking, self-storage and archiving facilities, water storage, underground quarrying, small industrial facilities and another layer of traffic (electric and fuel cell) and services network. Historically, blasting in high density population areas has resulted in blast vibrations and blast overpressures exceeding the limits, which in some case have been set extremely low in terms of peak particle velocity (PPV). This makes conventional blasting difficult, often requiring low charge weights per delay and associated small blast sizes and slow advance rates. However, the introduction of new technologies, such as computer aided drilling, electronic delays and low-energy explosives has made this task considerably easier. Although more expensive than conventional blasting, excavation by blasting using these products and technologies in relatively good quality ground is believed, in most cases, to be less than the cost of mechanical excavation. In this paper, the authors look at innovative trends in underground quarrying, underground commercial space and tunnelling and put forward their concept of future excavation demand, future product requirements and technical specifications to the drill and blast community.

Jan 1, 2007

Dust emissions from mining, material processing and ship loading operations (fugitive dust sources) are an environmental issue of increasing concern to both government regulators and the community. The main concerns relate to potential amenity, health and environmental impacts from the emissions. Therefore it is imperative that mining/ processing operations, as part of their overall environmental management, reduce fugitive particulate emissions to as low a level as is practicably possible. This technical paper outlines the mechanisms that lead to fugitive particulate emissions, the importance of understanding the exact cause of fugitive emissions, monitoring methods that can be used to quantify the emissions from specific sources, the use of atmospheric dispersion modelling in dust management and innovative dust management strategies including predictive meteorology and proactive management.

Jan 1, 2009

By D Lawie

Prior to resource modelling, sample scale data is normally grouped into spatial domains that reflect zones of homogenous properties. These domains are usually based on a combination of grade and other variables that reflect, for example, geology and alteration, or variables known to correlate with properties of the samples that affect downstream processing. Domaining and wire-framing sample scale data is a time intensive task and it is difficult to track more than a few variables simultaneously while establishing domain boundaries. This is especially the case in operations with complex data, for example, a combination of multi-element assaying of total element concentrations, and/or phase specific assaying such as sulfide sulfur, carbonate carbon, cyanide available gold, and/or downhole geophysical measurements. To minimise unintentionally grouping samples of contrasting properties within the same domain, unsupervised statistical methods are available that can automatically identify samples atypical of the domain, both as univariate tests, and as tests that take correlation within the domain into account. Unsupervised methods in this context means methods of identifying atypical samples that require just the selection of the domain and input variables. Thresholds are derived robustly from the data itself, and the results are therefore repeatable and operator independent. Atypical samples may be thought of as outliers, ie, samples that are separated from the ‘majority’ of the data. If these atypical samples are themselves spatially associated, they may be allocated to an alternative existing domain or allocated to a new domain. Care should always be taken to ensure that identified outliers are due to meaningful causes and not due to data coding and storage errors, although the identification of the latter is still valuable. *This is an abstract only. No paper was prepared for this abstract.*

Sep 5, 2011

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By L Ding, B Xu, C Wang

In this paper, we introduce the term ‘LJC’ to refer to the LJC Automatic Magnetic Flotation Separator, which is an advanced technology developed by Longi Magnet, integrating various techniques such as hydro separation, magnetic flocculation, and magnetic columns. This technology combines gravity, hydro separation, and magnetic separation to achieve efficient and reliable separation processes. With its low maintenance requirements and high reliability, the LJC technology has proven to be effective in magnetite processing. The LJC technology offers two primary benefits when compared to traditional magnetic drum separators. Firstly, it can enhance the quality of the targeted or improved concentrate at a coarser product size by minimising the carryover of gangue minerals into the concentrate. Secondly, it can significantly improve the concentrate quality (eg achieving >67 per cent Fe) while maintaining similar liberation size and mass yield. In China, this technology has been widely adopted in magnetite processing, replacing traditional magnetic drum separators and fines flotation in the final stage of the process. Through collaboration with a magnetite producer in Western Australia, Longi Magnet successfully implemented the next-generation LJC Automatic Magnetic Flotation Separator to replace the original stage 3 magnetic drum separators. The application of the LJC technology resulted in an increase in product P80 from 32 μm to 43.1 μm, while maintaining a final concentrate grade of 65 per cent Fe. Additionally, the power consumption, measured in kWh per tonne of concentrate, was reduced by 10 per cent. By eliminating the bottleneck caused by the requirement of a coarser liberation size to achieve the desired concentrate grade, the plant’s throughput was increased by significantly. The LJC technology has demonstrated its ability to reduce the carbon footprint, improve concentrate grade and enhance mass recovery, offering an alternative solution for magnetite processing. The high-grade magnetite produced by the LJC technology is particularly suitable as a raw material for Directed Reduction Iron and green steel production. This paper introduces the principles of the LJC Automatic Magnetic Flotation Separator and provides details of its application in a magnetite operation in Western Australia.

Sep 18, 2023

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

There are many types of environmental audit: compliance, impact, risk and management audits; internal and external audits; single and multiple-project audits. All are becoming increasingly important in corporate management as new legislation confers increasing personal liability on directors, executives and staff of corporations and agencies in both private and public sectors.

Jan 1, 1990

In 1972 the Marra Mamba Iron Formation in the Lower Proterozoic Hamersley Iron Province of Western Australia was recognised as a stratigraphic horizon with significant potential for high grade iron ore reserves. Within the Newman area the Marra Mamba Iron Formation has been subdivided into four strati- graphic units: Lower BIF member, Middle BIF and shale member, Upper BIF member and Upper shale member - and a standard natural gamma log reference section compiled for the entire formation. The recognition of the Upper shale member as an additional unit contrasts to the previously proposed stratigraphy. Enrichment of the Marra Mamba Iron Formation to ore grade (0)8 percent calcined Fe) in the Newman area is restricted to the Upper BIF member and to a lesser extent to the Middle BIF and shale member. Typical ore from Orebody 29 is friable interbedded martite-ochreous goethite, signifi aptly different both physically and chemically from the Brockman Iron Formation ores of the Tom Price-Whaleback type. Large scale customer acceptance trials (in excess of 4 million tonnes) have shown that Marra Mamba ore crushed to fines and blended with Mt. Whaleback fines in a ratio of up to 15:85 forms an acceptable sinter feed.

Jan 1, 1981

Contract mining is an integral part of the underground and surface hard rock mining industry in all states of Australia. Contract mining is now makes a major contribution to the opencui coal industry in Queensland and New South Wales with Thiess alone producing over 16 million tonnes per annum with safety performances that most coal companies would be proud of. Contract mining is now attracting interest in the underground coal sector.

Jan 1, 1998

In 1965, Peter Flawn author of the famous text-book on Mineral Resources (1966) published a paper in Economic Geology with the delightful title `Who took the `Economic' out of Economic Geology?'. He opened this most interesting article with the following paragraph:If one were called upon to cite an example of a fish out-of-water he could hardly pick a better one than a recent graduate of geology of an America university who is suddenly faced with the responsibility of evaluating or appraising a mineral property. And I venture to say that the 'ftsh' with a doctorate - even in economic geology - is not much better equipped than one holding a lesser degree. The new graduate with a major in economic geology probably knows the significance of the various sulphur isotopes, he surely knows a great deal about the chemistry of the ore forming fluids and he recites with ease the arguments which prove deposits are epigenetic rather than syngenetic. However he is a rare bird indeed if he knows anything about the economics of the mineral industry. The truth is that geologists who are engaged in evaluation work are largely self taught. I ask my more distinguished and experienced colleagues - `Has it always been this way? Who took the `economic' out of economic geology?

Jan 1, 1993

By C J. McKenzie, D F. S Natusch

The lignite deposits of Southland and Central Otago are a potentially significant energy resource for New Zealand. Current estimates put the technically mineable lignite reserves at 5.3 billion tonnes, which is more than ten times the energy content of the Maui gas field. Thus, the strategic importance of the lignite as a basis for maintaining current levels of self-sufficiency in transport fuels, or as a possible feedstock for electricity generation, deserves full investigation. The full extent of the lignite deposits was only recently established as the result of a scout drilling programme undertaken between 1976 and 1979 by the Mines Division of the Ministry of Energy, and from companion studies conducted by the New Zealand Geological Survey. These discoveries of large quantities of lignite coupled, at the time, with rising oil prices, raised the prospect of their development for production of transport fuels.

Jan 1, 1983

By F Grobler

Many projects fail because project performance in unfavourable economic conditions was not anticipated at the investment decision stage. This type of failure may have been avoided through the selection of a strategy that enables the project to perform well under a range of possible future economic conditions (a ærobustÆ strategy); rather than an æoptimalÆ strategy for expected future conditions that will never eventuate. This paper describes a method of rapidly generating mine plans for a number of project strategies, and then evaluating it against a representative range of equally likely economic conditions. The key performance indicators derived for each strategy are the mean value and the distribution of values (variance). A prudent investor will identify prospective strategies not only on the merit of highest mean values (as a proxy for economic reward), but also on the probability of not meeting specified investment hurdles (a proxy for risk). A robust strategy will achieve its financial objective even under adverse economic variations. This paper focuses on the effect of commodity price uncertainty; particularly around the choice of mining and processing capacity levels. Results from enumerating 2000 prices scenarios against 63 strategy combinations show how processing and mining capacity can be manipulated to manage the risk-reward trade-off.

Sep 26, 2011

In the mining and minerals industry, development, introduction and construction of new plant designs, to meet sustainability objectives, face a series of major hurdles. Typical are the long investment cycle times, the designer does not normally control the spending (the owner does), and the industry is inherently technologically conservative or risk adverse while accepting the often more significant geological, market and political risks.æSustainable Plant DesignÆ is an approach to plant and facility design that drives the necessary culture change and acceptance by minimising technical risk and maximising potential returns. The approach forces consideration of sustainability objectives and risks early in the project, where cost saving and efficiency improving opportunities can be maximised.In Hatch, we are using three proven tools under the ærisk managementÆ umbrella to drive sustainable development principles into our projects:Sustainable Plant Design, FutureWatchTM Reviews, and Clean Plant DesignTM . These proactive practical, not theoretical, techniques for driving change from within and reducing whole of life cycle costs will be discussed and illustrated with case studies.

Jan 1, 2004

ON milling plants, where a large number of slime samples are collected each day, considerable work is involved preparing them for the assayer. The usual practice (as the material usually passes a 150-mesh screen) is to place the sample on a 30-mesh screen an 1 brush it through on to a cloth below. The sample on the cloth is mixed and a portion taken out for the assayer. A simple apparatus that would rapidly disintegrate and prepare these slime samples for the assayer was needed. The manufacturers of assayers' supplies appear to have overlooked apparatus for this class of work. To overcome the tedious preparation of slime samples by the above method, the writer devised the apparatus shown in the accompanying drawing (Fig. 1). It will be seen that the apparatus is a combination of a modified household flour sifter and a riffle sampler.The apparatus is made up in two parts, the top half consisting of a screen box carrying the disintegrator, and the bottom half a, riffle divider, the joints between the two being a slip-in fit. A lid is provided for the screen box. The disintegrator consists of an open drum, to which are soldered three rows of spring steel fingers. Each row has a number of steel fingers which, on rotation, press against the semi-circular screen in the screen box, forcing the slime particles through.To operate the apparatus an 8-in. sample tin is placed under each spout of the divider. The sample of slime, which is about 2 lb. in weight and usually in lumps, is placed in the screen box, the cover replaced, and the drum rotated about half-a-dozen times by means of the handle.The disintegrated sample is divided by the rifle divider into two portions, which are found in the tins under the spouts of the apparatus. One of these samples is taken, mixed on a sheet, and sent to the assayer.

Jan 1, 1922

By Johnston G, Joyce C

The permitting of new mining projects has evolved into a highly complex process that must be carefully managed. Only by developing a thorough understanding of the issues involved and stakeholder interrelationships can successful strategies be developed that integrate the often competing demands of: ò regulatory requirements, ò commercial requirements, ò social/cultural needs, and ò technical issues. Properly implemented, this approach can result in: ò shortened approval timeframes, ò better project definition ò broad based community support, and ò favorably disposed government departments.

Jan 1, 1997

By S Mitra, B J. Monaghan, T Honeyands, G Evans, R Chowdhury, D Scimone

Due to the harsh operating conditions, wearing of the inner refractory lining in a Basic Oxygen Steelmaking (BOS) furnace reduces the useful life of the refractories and incurs a significant cost component for relining. In this study, firstly, a combined compressible and incompressible computational fluid dynamics (CFD) model was developed to identify the potential wear prone zones in an industrial scale BOS system during the supersonic oxygen blowing phase by quantifying the wall shear stress distributions. Next, the retained slag splashing process was simulated by introducing an inert gas to residual slag mass to achieve a protective coating on the refractory walls. Effect of both design and operational parameters such as lance head configuration, lance position and the initial slag volume on the slag wall coating performance were quantified and most favourable conditions were determined.

Jun 19, 2024

By R Valenta, I Fahey, M Klawitter, N Spanswick

Zinc-Lead-Silver (Zn-Pb-Ag) mineralisation at the George Fisher Mine occurs in multiple structurally-disrupted stratiform orebodies hosted within a mid-Proterozoic sequence of calcareous siltstones and variably pyritic shales (e.g. Valenta, 1994; Chapman, 2004). The geological model for the mine has been constructed based on a large number of stratigraphic domains which have been defined using recognised patterns of the constituent rocktypes, aided by recognition and mapping of K-rich tuff marker beds (TMBs). The continuity of these domains has been affected by the presence of several sets of faults which are extensional in the plane of stratigraphy, leading to the common occurrence of fault-related stratigraphic gaps in drillholes. Recent improvements to the detail of the geological model have led to significant improvements in the head grade of ore at George Fisher, with relatively small loss of metal. Recognition and accurate logging of these domains requires a high level of knowledge and expertise amongst mine geologists. In order to aid this process, the George Fisher mine installed a Minalyzer CS (core scanner) on site, with the aim of using high resolution X-ray fluorescence (XRF) geochemical data and core photography to increase the speed, accuracy and consistency of the site geological logging system. This contribution describes some preliminary results from a research project aimed at using the Minalyzer CS XRF data to perform high-resolution rocktype identification and domain boundary mapping in drillcore at George Fisher. CITATION: Spanswick, N, Klawitter, M, Valenta, R and Fahey, I, 2018. Rocktype classification and domaining of complex stratiform Zn-Pb-Ag mineralisation at the George Fisher Mine using high resolution XRF Core scanning, in Proceedings Complex Orebodies Conference 2018, pp 58–59 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Butcher NM, Walker GS

Argyle Diamond Mines Pty. Limited (ADM), manager and operator of the Argyle Diamond Mines Joint Venture (ADMJV) will recruit approximately 400 employees during 1985 to operate the new large-scale, open-cut diamond mine and treatment plant being developed at Argyle, in the East Kimberley Region of Western Australia. These employees will live in Perth or environs and will commute to work at Argyle via chartered jet aircraft. On site, they will be accommodated in self-contained single person's quarters, with central messing and recreational facilities. Rostering systems have not been finalised, but it is likely employees will rotate through a cycle of 14 days at site and seven-days on leave in Perth. ADM spent three years evaluating residen- tial options before deciding to commute its workforce from Perth. Another 70 senior staff will reside in Kununurra (the nearest established town, 250 km from Argyle) and commute to the mine daily by air.

Jan 1, 1984

This paper will examine the prospects for Queensland's non-fuel mineral industries as we approach the 21st century. The opportunity for growth is unprecedented. Exploitation of recent discoveries, proposals and developments in downstream processing are predicted to contribute to a doubling of the State's mineral exports to around $10 billion by the year 2000. In 1995 - 96 the value of Queensland's mineral production was $6 billion, comprising $1892 million metallic minerals, $127 million non-metallic minerals and $4 025 million total fuel minerals. For many years Queensland has been among the world's major producers of copper, silver, lead, zinc, bauxite and mineral sands. Recently Queensland has become an important producer of magnesia. Queensland's ability to compete results from its location close to rapidly developing Asian markets, the diversity of its major minerals and an increasing ability to add value to the resources base using competitively priced energy. Northwest Queensland is one of the richest base metal provinces on earth following the recent discovery of five world-class orebodies. Of these deposits, Osborne (copper-gold) has commenced production and Cannington (silver-lead-zinc) and Ernest Henry (copper-gold) are scheduled to be developed by 1997. Century Zinc Limited and the Queensland Government are negotiating with native title claimants on the development of Century (zinc-lead-silver). Expansion is in progress at the Mount Isa copper mine (renamed the Enterprise) and copper smelter and a high analysis fertiliser project may be developed based on Phosphate Hill. Korea Zinc Company Limited has reached agreement to construct and operate a 350 000 Mtpa zinc smelter/refinery near Townsville. There are future expansion prospects for the vertically integrated major industrial mineral operations based on Weipa bauxite and Kunwarara magnesite. Upgrading of the Boyne Island aluminium smelter will require a doubling of alumina consumption. Downstream processing options for Kunwarara magnesite are being investigated and are expected to lead to increases in production and the manufacture of a range of value-added products. At the Yabulu refinery near Townsville, nickel and cobalt production using imported ore is to be increased and a commercial cobalt plant is to be built. Additional opportunities for further processing and manufacturing are associated with proposed new mines at Ely (bauxite), Skardon River (kaolin) and Goondicum (ilmenite). Recently discovered resources of zeolite and perlite also offer exciting development possibilities. Other manufacturing opportunities such as glass and ceramics based on local and plentiful clay and silica sand could replace imports. Silica sand at Cape Flattery is currently exported and production is expected to double.

Jan 1, 1997

By P M. Cepuritis

In hard rock mining, large-scale bulk mining methods such as block or panel caving (BC/PC) and sublevel caving (SLC) typically generate significant surface deformations such as subsidence. Surface deformations need to be considered in the project evaluation and planning stages of cave mines, for example, planning and location of critical underground mine planning infrastructure such as portals, haulage and vent shafts, access roads, or potential damage to existing infrastructure, changes to surface water management, waste dump, stockpile and tailings dam stability, and environmental impacts. Assessing the impact and risks associated with subsidence is a key component in robust mine planning and operations management.

Nov 29, 2022