Search Documents

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

Recent exploratory work has greatly enlarged our knowledge of the geology of the sedimentary basins of Western Australia. The most pros-pective of these for oil explorati on are believed to be the Canning, Carnarvon, 'and Perth Basins.The search for oil. in, the Canning Basin has fora the most part been concentrated in" the western part, where four main structural units are now recognized - the Lennard Shelf, Fitzroy Trough, Jurgurra Terrace, and-South Cariizin.g Basin. Of these the Leonard Shelf may. be the'most prospective. The principal objective on the Shelf is the Devonian sequence, which in-cludes well'developed reef complexes. The Lower Carboniferous is regarded., as a further objective, as it contained small quantities of oil in theMeda No. I well.In the. Carnarvon Basin most explorati on has been conducted in the coastal belt of'Tertiary folding, especially in the Cape Range-Rough Range area. -The discovery of oil in the first test well. drilled.in the-basin - Rough Range no. 1 - raised great hopes, for the quick discovery of a ecmuercial field. However the other wells on Rough Range have been dry, and no discoveries have-been made in the-wells drilled on other anticlines.in the basin.

Jan 1, 1962

By A Tsoy

This abstract describes long-term mining schedule optimisation approach that may be suitable for complex marginal projects and is based on modern scheduling techniques. CITATION: Tsoy, A, 2018. Strategic mine schedule optimisation, in Proceedings Complex Orebodies Conference 2018, pp 91–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M A. Tuck

Air blasts or wind blasts as they are termed in underground coal mining, occur in a number of types of underground mining where a void develops and the overlying or adjacent rock fails rapidly to allow the development of a high pressure air pulse. The effects of air blast vary widely from very low consequence to high consequence events causing multiple fatalities as occurred at North Parkes mine. The aim of this paper is to examine the phenomena of air blasts and the underlying parameters which determine the severity of the air blast event. A basic model under development is then detailed. The aim of the model is to determine the magnitude of the pressure pulse(s) developed during an air blast event. This, combined with a transient ventilation network analysis model will enable the airflows and associated pressure drops to be determined and allow the pressure pulse around the mine to be evaluated. The overall aim is to allow mining engineers and mine ventilation engineers to undertake a risk assessment of air blasts at individual mine sites, allowing working parameters to be changed to eliminate or reduce air blasts, or engineering controls to be developed to reduce the effects of air blasts.CITATION:Tuck, M A, 2013. Determining the pressure pulse for an air blast, in Proceedings The Australian Mine Ventilation Conference , pp 103-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By R Saha, D Barry, C Mawdesley, O Bertoli

Kriged estimates are not typically calculated on blocks substantially smaller than the sample spacing (eg the Standard Mining Unit or SMU). Moreover, the sample spacing for quality variables is often much greater than the SMU size. For short to medium term planning decisions, the shorter term variability in the quality variables is a key economic consideration in defining, setting and meeting coal product specifications.Global uncertainties can be calculated using Drill Hole Spacing Analyses (DHSA). However, knowing the precision of a variable for a one or two year production volume is usually not adequate for variables with low spatial continuity that may fluctuate significantly over daily, weekly, SMU, or shipment volumes.Is there a feasible, reasonable and valid geostatistical method to model the uncertainty of coal quality variables on blocks substantially smaller than the drill spacing (say on the SMU)?The validity of using co-kriging variances, calculated on SMUs to characterise local uncertainty, was tested using a suite of conditional simulations generated for several quality variables for BHP’s Blackwater operation. The conditional simulation results were used as a benchmark against which the results derived from the kriging variances could be compared.The agreement between the kriging and simulation methods for thickness is excellent, with much closer correlations than for the quality variables. Typically, the kriging variances give very reasonable approximations to the simulation-based uncertainties, although there could be some systematic discrepancies which may become much more critical if a classification is to be based on a thresholding of the SMUs relative uncertainties.CITATION:Mawdesley, C, Barry, D, Bertoli, O and Saha, R, 2017. Local uncertainty benchmarking – a coal case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.Recent increases in prices for iron ore, together with the potential to produce high iron and low contaminant concentrates, have resulted in a renewed interest in recovering magnetite from banded iron formation and other deposits.Geometallurgical evaluation of magnetite involves approaches to sample preparation, sample analysis and resource estimation that are different from the methods commonly used for haematite iron ore. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.The sampling protocol will typically include the use of Davis Tube analysis. The Davis Tube is a bench-scale test that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery.During resource modelling, the mass magnetic recoveries and concentrate grades may be assigned to a block model using regressions with other chemical constituents, or may be estimated directly. For estimation of the concentrate grades, a weighting can be applied to account for the different mass magnetic recoveries from each sample and the impact of these differences on the concentrate estimates.This paper presents an overview of the use of metallurgical test data in resource evaluation for magnetite deposits.

Jul 11, 2011

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

By Grant BPM

The lower levels at the CSA Mine have been developed to mine reserves between theNo.7 level and No.9 level.Work on major excavations for the project began during 1982 with the develop-ment of the crusher chamber, on No.9 level. The brows and walls were pre-dowelled to improve stability before mining by mass blasting techniques.At the same time work commenced on theextension of No.2 Shaft from No.7 level toNo.11 level. The shaft was stripped, using hand held drilling, to a raise bored holeand concrete lined to a diameter of 5.5 metres. Plats were developed at No.8 level, No.9level and the loading station.

Jan 1, 1985

By A Jewbali, R Perry, R Inglis, L Allen

"The use of conditional simulation to characterise mine plan uncertainty is increasing for the assessment of risk in mining projects. While the development of grade uncertainty profiles is relatively straightforward and can be validated using standard geostatistical techniques, the addition of geological uncertainty to evaluate total risk remains problematic. Some of the problems associated with geological uncertainty methods include the clustering of data in favourable geologic units, difficulty in training image definition and the inability to address change of support issues for categorical variables. Despite these obstacles, the importance of geological uncertainty as a contributor to total uncertainty has prompted Newmont to explore and evaluate the use of various techniques (and combinations of techniques) on different deposit types.Two orogenic deposits of different geological complexity were selected for the study: Subika, a shear zone-hosted deposit, and Merian, a deposit containing gold mineralisation associated with quartz vein zones and stockwork within which are found higher-grade quartz breccia zones. Newmont trialled various categorical simulation approaches to determine the applicability of these methods for each deposit type and the effect of parameter choice on the width of the uncertainty interval. Some of the techniques that were trialled include multiple point statistics methods, sequential indicator simulation using local probabilities as well as variations of these methodologies.The goals of this study included: gaining an understanding of which techniques may work best in which deposit types gaining an understanding of the intricacies of each method gaining an understanding of the effect that each method has on total uncertainty analysis.This paper presents a comparison of the various techniques and makes recommendations for their use in uncertainty analysis.CITATION:Jewbali, A, Perry, R, Allen, L and Inglis, R, 2014. Applicability of categorical simulation methods for assessment of mine plan risk, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 85–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By C Sylvestre

Leaders have invested heavily in traditional safety management to improve safety performance over the years. This primarily involved: • fixing the environment (eliminating the hazard) • improving the system (more/less rules, procedures etc) • making safety more conscious (more/better interactions about the importance of safety). These approaches have helped improve safety performance significantly during the last 50 years and will continue to play a role in the future. Although these approaches may be part of an overall solution, they are not enough to prevent many incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

Government established and financed the NZ Steel Investigating Co in 1960. Its investigations showed that a steel industry was feasible and desirable based uponNorth Island titanomagnetite ironsands, and charted a route for its establishment. The initial processing used post-1945 preheating and prereduction developments, but later innovative improvements created what was essentially a new New Zealand technology. Of the North Island titanomagnetite deposits: the small ones at Waipipi were best made available for export; those at Kawhia and Taharoa were too remote for the economic siting of a mill; that at Raglan proved too small; while at Waikato North Head three times the requirement of 50 million tons of concentrate were located in two sand areas averaging 18 per cent titanomagnetite. Economic studies showed that a South Auckland site would be ideal, close to New Zealand's biggest market. The mill site, on a basalt flow at Glenbrook, was located by a half-day's fieldwork - near both the Waikato North Head deposit, and a railhead for bringing in Waikato coal, etc, and taking out steel products.   This development was one of several since World War II which altered significantly the lives and homes of New Zealanders (others were natural gas, oil, geothermal power, epithermal gold, aluminium, opencastable lignite, etc). All had the essential ingredients of the highest government backing, direct or indirect government finance, and first-class New Zealand scientific and engineering skills (eg to create new technologies). Not one such project failed.

Jan 1, 1993

By G R Ryan

Dissatisfied with conventional wet processing methods for alluvial deposits, Resource Trend Pty Ltd of Cairns set out to develop a better process. After comprehensive investigation of existing dry techniques the principals have now developed a rotary dry concentrator that can handle the fine-grained fraction of alluvial deposits as well as the coarse. Four of these units have been mounted on an integrated towable treatment plant which has been in successful commercial operation for four years in northern Queensland. A second plant is now under construction for use in the United States. Grades of less than 0.2 g/lcm have been profitably mined at throughputs of about 80 cubic metres per hour and 85 per cent availability. The operation runs round the clock with an establishment of four. Major benefits, apart from lower capital and operating costs, are environmental. Ore is picked up, treated, and replaced in its original mixed condition within 25 m of its initial location. Rehabilitation is completed almost immediately behind the plant as it advances, leaving no slimes dams, coarse stockpiles, or haul roads. In 1993 the company won a Premier's Award for Environmental Excellence in the Queensland Mining Industry. The principal disadvantage is moisture, and the company is now actively seeking deposits in the deserts of the world. In Queensland mining is normally possible only for six months of the year.

Jan 1, 1994

By B Murphy

Seeking to reduce the likelihood of uncontrolled personnel entry into the operating footprint of a dragline, Coronado Global Resources initiated a review of proximity detection systems currently available and equipment interactions in and around dragline operational areas. At the time of the assessment, there were no established personnel proximity detection systems in compliance with functional safety standards for large machinery in Australia. Our primary objective was to guarantee a functionally safe outcome, particularly by implementing a performance-level-rated system in accordance with AS4024 (Safety of Machinery series of Australian Standards). Applying appropriate detection technologies, the goal was to reduce the residual operating risk for machine-to-machine and machine-to-personnel interactions. A comprehensive analysis of available or in-development technologies was conducted, and a layered approach (demonstrated in Figure 1) was adopted to achieve the desired risk reduction by segregating the sensing zones into distinct areas using diverse and disparate technologies consisting of radar (short); light detection and ranging (LiDAR) (medium); and optical (long). To address the potential limitations of each technology, overlapping layered sensing zones were designed. With LIDAR and optical using two distinct artificial intelligence (AI) systems to classify detections, these were specifically trained to handle the unique environments of a mining operation.

Sep 1, 2024

Thank you for the opportunity to speak at this important conference attended by aspiring mining professionals, some of whom will become the leaders of the mineral resources industry that forms the solid foundation of AustraliaÆs past and that will fuel the exciting growth of AustraliaÆs future.I want to briefly touch on the history of our business, then look at the opportunities that exist in the contract mining industry and finally comment on what the educators need to consider in their curriculum to meet the needs of our business. Byrnecut started out as an idea in early-1987 developed by a group of four mining people. At the time the industry was on the high end of a mining boom, the era of the Bonds, Connels, Skases and so on. Riding on this wave of euphoria we borrowed $600 000 from the National Australia Bank and, without having enough knowledge to lose sleep over the potential risks, started business in mid-1987. The euphoria quickly evaporated with the 1987 October stock market crash. The bank pulled our overdraft, equipment finance rates increased to over 20 per cent per annum and my house was mortgagedseveral times over. The business learning curve was extreme for a young mining engineer who had developed his trade in the relatively sheltered environment of a large public mining house, namely WMC. We were somewhat bitter that the banks had done a runner. We were a private company, backing the business with personal assets with our shoulders to the wheel, whilst the Bonds of the world had theirnoses in the trough ripping off mum and dad shareholders. All of this had a sobering effect, namely keep your feet on the ground, stick to the knitting, work hard and worship cash flow. Since that stressful but adrenaline pumping beginning the company now employs over 600 people and is now working for major mining houses at over a dozen locations in Australia, east Africa and WesternEurope and the National bank is again our banker. On this basis I consider myself qualified for the subject of this speech.

Jan 1, 2002

With the use of 36 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt Lyell Mining & Railway Co, it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5000 feet of boring the total cost of new parts is noted on this line (see Figure 1). Thus at a glance it is possible to see the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this clifficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component.As before the cost of new parts are taken at each 5000 feet bored (see Figure 2).

Jan 1, 1994

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By Madgwick J. C

Bacterial leaching of museum grade chalcopyrite and chalcopyrite concentrates at low sorptive relative humidities (55-91 per cent rH) was demonstrated. Optimum release rates were 13 and 27 mg/gram/100 days copper (Cu++) at 91 per cent and 80 per cent rH and 12 and 33 mg/gram/100 days iron (Fe++) at 80 per cent and 73 per cent rH for concentrate and "pure" chalcopyrite respectively. The optimum copper release rates occurred between 73 per cent - 86 per cent rH and 30-40 mM acid concentrations. Bacterial copper leaching rates were some twenty times slower for emersed copper concentrates, at low relative humidity, compared with submerged cultures. Bacterial copper solubilization was almost quantitatively inhibited above 150 mM acid levels (< pHO.8).

Jan 1, 1984

By Sheridan GD

Fifteen samples 'of clays and shales from the Adelaide area were selected from a total of 84 as representing material of possible value for the manufacture of light-weight aggregate. A detailed examination of the bloating. characteristics of these revealed four likely to be suitable. for expansion.' in a rotary kiln. One of these, a Tapley. Hill shale., was-fired in an 8 in. diameter rotary kiln, but con-tinuous bloating without ring formation in the kiln was not achieved. Steam,,-oxygen,, sulphur dioxide and carbon dioxide have been, suggested. as the agents of bloating. An examina-tion of .. the evidence : `leads to the conclusion that carbon dioxide derived from. carbonate minerals is likely to be the principal bloating agent. Attempts to bloat clays by the addition of mica were.not successful.

Jan 1, 1963

By A Hosseinzadeh Barforoosh, A Abedi, M Taji

The effect of blast loads on beams is one of the main issues in the analysis of steel structure. In this study, experimental tests on steel beam under blast loading, and also numerical simulation by the Autodyn software to analyse these structures, is discussed. Experiments on steel beam size of 12 by Emulite4 explosive with 30 mm diameter and cortex is done. The patterns of cutting and bending generated in the two tests (empirical and simulation) show a good match.CITATION:Taji, M, Hosseinzadeh Barforoosh, A and Abedi, A, 2015. Comparison of experiment and simulation of blast loading on the steel beam, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 161–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015