Search Documents

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By G Solly, S Parsons, P Leevers, S Ni

Hematite ore has been mined in the Southern Middleback Ranges as blast furnace feed for the steelworks at Whyalla, by what was then BHP, since 1991. With the floating of BHP Integrated Steel as OneSteel in 2001 and the subsequent loss of key mining personnel, breakdowns in grade control methods and procedures occurred. These were compounded by changes in orebody characteristics and grade distribution leading to poor reserve recovery and poor grade control, both which resulted in loss of control of ore specification and severe deviation from the mining schedule. As a result, a total review of grade control, mining method and scheduling procedures was undertaken as well as a review of contractor quality assurance. It was found that sampling methods were poor and unrepresentative, grade control blocking processes were outdated and did not reflect the geology of the deposit, the ore mining method was outdated and did not respect the geometry of the orebody, reconciliation methods were being completed globally and were not reflective of individual areas of the deposit, and that deviations from the mine plan were occurring due to access to high-grade areas outside the schedule in order to bring stockpiles back on grade. Based on these findings, updated sample splitter systems were fitted to drill hole rigs, double bench sampling was implemented (2 + 4 m samples as opposed to 1 + 8 m sample) and a three-dimensional cellular grade control system introduced to better reflect the geology and orientation of the deposit. At the same time ore mining was changed from front end loaders mining on 8 m benches to excavator mining on three lifts on 8 m benches; this aided selectivity and respected the geometry of the orebodies aiding cleaner recovery. Reconciliation is now completed on a blast-by-blast basis, which allows for quick and easy identification of poorly performing areas of the resource model that can then be incorporated back into resource model updates. Regular daily and weekly meetings are also held with emphasis on the mining schedule to ensure no deviation from the schedule in the long term. These improvements have resulted in a lift in reserve recovery both globally and locally associated at the same time with improvement in grade.

Jan 1, 2005

By Yu A. B

An experimental study of the packing of a coal heap has been carried out. The bulk density of a coal heap is considered as a function of a number of variables, viz flow rate, conveyor belt speed, the height of the disengagement point of the conveyor belt, coal particle density, moisture content, the size of the heap and coal particle size distribution. The effects of the dimensionless numbers resulting from dimensional analysis on the packing density of a coal heap have been experimentally examined and analysed. Based on the experimental results, equations have been formulated for the estimation of the bulk density of a coal stockpile. The validity of these equations are checked by comparing the predictions with measurements of real industrial Stockpiles.

Jan 1, 1991

The selection and implementation of the right technology for a project is critical to the future development of the resource industry. It is essential for companies to ensure ongoing competitive viability that where practical new or alternative technology be adopted. Analysis of historical data relating to development of resource-based process plants provides an enlightening insight into the key factors which influence their success or failure. The adoption of new technology does not guarantee the success of a project. The outcomes of this analysis have been used to develop some general guidelines and principles the author believes are useful in the selection and implementation of new or alternative technology in resource projects. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

By G Collecutt, D Proud, D Humphreys

"The hazards associated with dust explosions are well known, and coal dust explosions present a significant hazard in the underground coal mining industry worldwide. In earlier work, we presented computational fluid dynamics (CFD) simulations and test results for coal dust explosions within a 2.5 m diameter circular gallery, along with CFD simulations and test results for the suppression of these explosions with finely atomised water sprays. In this paper, we present refinements to the CFD modelling that yield a significantly improved calibration with the test results, and proceed to investigate by CFD the requirements for suppression of a coal dust explosion in a typical underground roadway. This work was carried out under an ACARP project and we gratefully acknowledge their assistance. CITATION: Proud, D, Collecutt, G and Humphreys, D, 2015. Computational fluid dynamics modelling of coal dust explosions and suppression systems, in Proceedings The Australian Mine Ventilation Conference, pp 309–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By J Webb

"It is vitally important in projects where the cut-off grade is low that there is no contamination during the sampling and sample preparation process, both in the ore and the waste zones. Failure to identify contamination could have devastating financial consequences for a project. The use of a variety of blank types is essential for ensuring that contamination is identified and eliminated at every stage of the sampling and sample preparation process. This paper examines an instance where an effective assay quality assurance and quality control (QA/QC) program was able to identify and eliminate a source of significant multi-element contamination in the prefeasibility stages of an open pit project. This examination includes the: evidence for contamination findings of the investigation process of resolving the problem and correcting the data evidence for both addition of metal and dilution through contamination potential impact on the project had this issue not been dealt with. It was through the use of a combination of blank types that the QA/QC process at Mount Isa Mines (MIM) identified a contamination issue at the first crushing phase of sample preparation. Identification of the contamination allowed MIM to stop assaying activities and work with the laboratory to correct the problem. The sampling program could then be continued with no further doubts about the sample preparation process. Contaminated samples were resampled from retained core. With the continuous monitoring provided by the blanks program, it was possible to ensure that only clean results went into the resource modelling data set. CITATION:Webb, J, 2014. When nothing is what you need – the importance of using blanks at all stages of sample preparation, in Proceedings Sampling 2014 , pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

At the outset I want to thank you for inviting a representative of the Chamber of Mines of South Africa to address you on the subject of mining and its future at this, the 13th Congress of the Council of Mining and Metallurgical Institutions. It is indeed a pleasure and an honour to be here. As many of you will recall, four years ago I, as the then President of the South African Institute of Mining and Metallurgy, had the privilege of hosting and welcoming you to the 12th Congress, the third such congress hosted by South Africa. The late Sir Ernest Oppenheimer, President of the 1930 Congress - the first to be held in South Africa - in his opening address foresaw the mining industry as "the most potent factor in spreading the benefits of civilisation over the sub-continent." We have come a long way since those halcyon days but, as I noted four years ago, it still remains true that mines have been, and will continue to be, the missionaries of development in many, if not most, of the Third World countries. I have been asked to address you on the subject of "mining" and to let my imagination roam widely so that delegates can leave the congress with a broader vision than they brought on arrival. It is a tall order and in my attempt to fulfil it I ask you to cast your minds back 120 years to a sultry, rustic day when the first diamond was discovered in South Africa at the now famous town of Kimberley. At that time the South African economy, predominantly pastoral, was still at subsistence level. Almost overnight the ensuing diamond rush turned the then British- owned northern Cape Colony's semi-desert scene into a hive of mining activity, every prospector bent on making his instant fortune. It was very little different, I am sure, to the gold rushes that hit California in 18+8, Australia in 1851, New Zealand in the 1860s. and the Yukon in the 1890s.

Jan 1, 1986

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By B Patterson, Y Lanwin

Over the last decade the adoption of autonomous technology has proven its potential to fundamentally alter the mining industry, offering significant improvements in safety and productivity. Automation levels are now increasing exponentially across all parts of the supply chain from drilling, haulage, processing, rail and shipping to the maintenance of the above. However, the management of human error risk is also becoming increasingly complex as the disconnect between the people who operate and interact with mining equipment and those that design the autonomous systems grows in terms of skill and expertise. Furthermore, as comfort levels with automation increases amongst operators, complacency is increasing as the initial functional safety benefits have been realised. This paper introduces an innovative concept that unites two distinct fields, functional safety and behavioural economics, to address the complex issue of human error risk in autonomous mining operations. Functional safety, a well-established field in engineering involves identifying potential hazards, assessing risks and designing systems in a way that minimises the chances of accidents and limits their consequences. Meanwhile, behavioural economics takes a data centric approach to analysing the psychological aspects of human decision-making, acknowledging and seeking to understand the errors that can originate from cognitive biases and heuristics. This paper seeks to bridge these domains by emphasising that human error in autonomous mining is not solely a technical issue but is deeply influenced by human behaviour and decision-making processes. By incorporating insights from behavioural economics, we can better predict, prevent and manage human errors in the mining sector. By applying principles from both disciplines to a recent incident example we will explore how cognitive biases can impact peoples’ interactions with autonomous mining equipment. This interdisciplinary approach will not only enhance the design and implementation of functional safety measures in mining but also lead to the development of people centric solutions that consider the inherent fallibility of people. We will explore how human centred design can help bridge the gap between these two domains and apply systems thinking for a universal approach. Through an indepth case study analysis and empirical data, our research aims to provide actionable insights and practical recommendations for mining industry professionals, regulators and stakeholders involved in the safe integration of autonomous systems.

Apr 16, 2024

By T Kon, K Ohno

Slag foaming is an important control item in the process of refining molten steel. This study aims to investigate the factors controlling slag foaming by observing the bubble formation behaviour resulting from the chemical reaction between iron oxide and Fe-C alloy in the slag. In this study, 0.06 g of Fe- C alloy was introduced at the bottom of a BN crucible, and 6.0 g of slag (SiO2:CaO:Fe2O3 = 40:40:30) was placed on top of it. The crucible was positioned inside an infrared image heating furnace, where the temperature was rapidly raised to 1370°C at a rate of 1000°C/min in a nitrogen stream, and then held at that temperature for a predetermined time before rapid cooling. Following rapid cooling, the internal structure of the sample was examined using a high-resolution X-ray CT device. The spherical equivalent volume was calculated based on the number of observed bubbles and their equivalent circle diameter. Additionally, the relationship between the volume ratio of small bubbles in the slag volume and the distance from the bottom of the crucible was determined, along with the calculation of bubble density and volume ratio. Under various experimental conditions, numerous bubbles with equivalent circular diameters ranging from 200 to 300 μm were consistently observed. The density and volume fraction of bubbles with circular equivalent diameters between 200 and 500 μm showed a tendency to increase as the distance from the bottom of the crucible increased. Bubbles with equivalent circular diameters of 500 μm or more consistently exhibited lower bubble densities, regardless of their height within the crucible. The formation of larger bubbles is attributed to a decrease in iron oxide concentration within the slag as the reaction progresses. However, this is believed to be due to their higher buoyancy, resulting in shorter residence times within the slag and a reduction in the number of encapsulated bubbles.

Aug 21, 2024

Energy is central to respond to critical stakes on human and industrial development requirements as well as on climate change. The increase of the share of carbon-free energy sources in the global supply mix will help to reduce significantly greenhouse gas emissions (GHG) as power generation accounts currently for 41 per cent of these emissions from the energy sector. In this energetic mix, nuclear and renewable energies are complementary, the first more focused in the baseload power generation whilst the second is well suited for decentralised power generation. In this context, AREVA's goal is to enable everyone to have access to a cleaner, safer and more economical energy. Regarding nuclear energy, AREVA's strategy is to capitalise on its integrated operation model, which groups together fuel cycle and nuclear power plant construction, aiming at building one third of the new nuclear capacities and securing the fuel cycle supply chain for its existing and future customers. Therefore, the front end of the uranium fuel cycle, from mining to the fabrication of fuel assemblies, has a key role in the sustainability of the nuclear industry. The replacement of the current capacity and the entrance of new countries on the nuclear power generation might lead to a significant rise of uranium demand by 2020. In order to be prepared in time, AREVA defined an ambitious industrial program to expand mineral reserves, increase the production of uranium concentrates, replace the conversion capacity, build two new uranium enrichment plants, one in France and one in the United States and upgrade its fuel manufacturing plants. To support the front-end industrial activities in the short and long term, AREVA invests on a portfolio of R&D projects to find out solutions to meet customers' needs, to improve its competitiveness and to develop new concepts and solutions to anticipate future market evolutions. In particular, some important technological challenges in mining must be surmounted to develop cost-effective methods to explore and exploit low grade deposits while creating sustainable solutions for reducing reagent, water and energy consumptions. In this lecture, an overview of the industrial investments of AREVA in the front end of the uranium fuel cycle and some highlights on its R&D major axis will be presented. This is an abstract only. No full paper was prepared for this abstract.  

Sep 13, 2010

By Riel RG

Nickel and cobalt mineralisation at the Murrin Murrin deposits, in the North Eastern Goldfields region of Western Australia, occurs within laterites developed on Archaean serpentinised peridotite units. Lateritic weathering of the peridotite has produced a resource of 116.8 Mt at 1.10 per cent Ni and 0.082 per cent Co (resource at May 1996 with a 0.8 per cent Ni cut-off; see Fazakerley and Monti, this volume). The mineralogy of the Murrin Murrin laterites was investigated to identify the minerals hosting significant Ni mineralisation. Laterite profiles were studied using X-ray Diffraction (XRD), impregnated polished thin sections, and Energy Dispersive Spectroscopy (EDS) Electron Microprobe analysis, of RC percussion drill chips. This paper summarises the results of these studies, and briefly discusses the nature of the minerals hosting Ni mineralisation.

Jan 1, 1996

By S Leary

Diamond drilling since early 2006 has identified an epithermal gold-silver (Au-Ag) deposit beneath 140 m to >400 m of cover. The Fruta del Norte discovery had an inferred resource estimate of 58.9 Mt grading 7.2 g/t Au in October 2007. The mineralisation is hosted by Mid-Late Jurassic andesite and andesite porphyry in a regional fault zone beneath mainly post-mineral but in part syn-mineral Late Jurassic cover. The intermediate sulfidation-style deposit formed before and in part during deposition of epiclastic cover in the fault related pull apart basin. In addition to its size and obvious economic importance, the widespread occurrences of visible gold and exquisitely preserved epithermal textures will make Fruta del Norte an important learning tool for explorationists seeking epithermal mineralisation in theAndes and elsewhere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D J. Brake

In most underground mines, the ventilation system is a significant portion of the total mine capital and operating cost and the largest consumer of underground electrical power. The effectiveness of the ventilation system has a major bearing on the safety, health, comfort and morale of underground personnel, and has a critical role in meeting production targets and therefore business revenue. Perhaps the most important component of the primary ventilation system is the primary fan. Correct performance testing of the primary fan during the warranty period is important not only to ensure the mine has obtained the asset that it paid for and can therefore deliver on the fanÆs crucial safety and economic role in the future of the mine, and to provide a justification for releasing final performance warranty payments to the supplier, but also to provide a benchmark or baseline against which to assess future performance issues. As there are at least three potential international standards available to measure fan performance, there has been considerable confusion regarding which of these to use for testing primary mine fans, and also the correct allowances and tolerances to use. This paper provides guidance on which standards to use for different applications, how the standards should be interpreted, what allowances and tolerances are reasonable, and other important issues to be resolved with the fan supplier prior to making a contract award. The paper also discusses practical issues and methodology for in situ primary fan performance testing.CITATION:Brake, D J, 2013. Performance and acceptance testing of main mine ventilation fans, in Proceedings The Australian Mine Ventilation Conference , pp 141-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Stradling

For a geometallurgical program to be successful, linkage must be made between the geologists and geostaticians who understand and model the orebody, the metallurgists who determine the value that can be extracted from the different geometallurgical units, and the mine planners who develop and optimise the plan to extract maximum economic value from the resource. One of the primary purposes of geometallurgical models is in the determination of the economic cut-off between ore and waste. Recognition of the level of confidence required in the estimation of grade, throughput and recovery is critical to the planning of a successful geometallurgical program. It also helps clarify the scope of work needed to mitigate risk at each stage in the development of a new mine projectThis presentation provides some of the author’s experience with development and application of geometallurgical models for existing base metal operations. It discusses how geological units defined by lithology, structure, alteration etc, can be translated into geometallurgical ore types defined by mineralogy, ore hardness, and flotation behaviour. Examples of how these characteristics have been used to estimate key economic parameters such as mill throughput and flotation recovery at two brown-field operations are provided. The first example relates to the modelling of metallurgical performance at Teck’s Red Dog zinc-lead mine in Alaska. Prior to 2000, zinc, lead and silver recoveries from a block of ore at Red Dog were either assumed constant, or were varied according to simplistic models. Throughput was not thought to vary substantially between blocks, so an average value was used for each blended stockpile. It is quite possible that some ore-value blocks were classified as waste, and some waste-value blocks treated as ore, as a result of poor understanding of the true economic cut off across the wide range of ore types observed at Red Dog. After an extensive flotation test program, the first assay-based zinc recovery model was developed for the Main pit reserve in 2003.**This is an abstract only. No paper was prepared for this abstract**

Sep 5, 2011

This presentation is a 20 minute snippet of my professional career, and my progression in the mining industry, from a lazy uni student to an up-and-coming blast engineer in the middle of a mining boom.My name is Daniel Hepburn and I am a blasting engineer for Orica Mining Services. I graduated from Royal Melbourne Institute of Technology (RMIT), in Melbourne in 2003. I completed both of my final year projects with Orica Quarry Services and was offered an assistant shotfiring job, which I accepted and worked for eight months. Having missed the cut-off date for the Orica graduate program, I planned to work with Quarry Services until the following year where I hoped my marks and the experiences I had gained would secure a graduate position. I didnÆt have to wait long, as in August of that year, I was offered (and I accepted) a graduate position in Perth as a technical services engineer for Orica Mining Services. The Orica graduate program is based over two years, and consists of real roles from day one; however, there is also opportunity to fast track the program for high performers. There is a structured rotation, from site to site, interstate or even international if you are so inclined. This includes the backpacker program, which allows graduates to experience the Orica culture in countries of their choice. There are also opportunities to try cross-functional roles in the different Market segments within Orica. I was lucky in that I knew what I wanted to do and where I wanted to work, so I stayed in Perth for my entire graduate program. I was also lucky enough to be fast tracked and finished my graduate program in 15 months. At the end of 2005 I accepted a position as an open cut blasting engineer based in Perth and even in such a short period of time I have already completed a number of major accomplishments. Some of these accomplishments are described below. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By A Dix

Fire suppression systems are but one of the many technologies currently available to manage operational tunnel risks. However, the actual reasons for their use are often shrouded in mischievous discussions of the marketing variety.The international tunnelling community still stands divided on the merits (or otherwise) of fire suppression systems. For some the debate focuses on their cost compared to the theoretical benefits they bring to human safety.Long standing concerns about their potential adverse effects in an emergency are often at odds with the experience from tunnels which use them. High installation and operational costs are cited as reasons not to use them, yet toll road operators and insurers increasingly use them as a risk mitigation strategy for toll revenue protection.Fact or fiction, myth or reality, should such systems be seriously entertained or are they just another expensive gadget in the escalating array of expensive toys for modern tunnels? Ultimately this presentation argues that they have their place as a risk mitigation measure to achieve a range of objectives. The exact circumstances for their use ultimately fashioning their design and operational characteristics. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

Leaving the relatively simple life on a uni student and venturing off in to the outside working world is a big step. There are two paths to follow, the æContikiÆ style graduate program where you pick up your new lease vehicle and set forth on two to three years of planned activities, or can pack everything into one bag, stick a copy of æthe rough guideÆ in your pocket, and set off on your own graduate adventure. I took the path less travelled.The less followed method of developing yourself isnÆt for everybody. Parts of the journey are difficult and sometimes it feels hopeless, but itÆs all a learning experience. Along the way you might not get to all the graduate ætourist stopsÆ like dragline, truck-shovel, or drill and blast. But youÆll see most of them and pick up a lot more of the local culture such as people management, operational knowledge, quality control, and the black arts of project financial management.

Jan 1, 2004

By P Odins

Traditionally, stratigraphic deposits have been represented by a large number of gridded surface and product analytical models, related to each other by naming convention. This approach, though suitable for structurally simple stratigraphic deposits, does not lend itself well to addressing the complex style of stratigraphic deposits which are becoming more prevalent. In addition, the sheer number of individual gridded models involved makes it very difficult to keep a consistent audit trail of the overall deposit model. Recently, a new enhanced block model structure known as Horizon Adaptive Rectangular Prism (HARP) models was introduced to address these issues. An HARP model is specifically designed to allow stratigraphic units to be represented with virtually no loss of structural integrity, by allowing the tops and bases of the individual HARP blocks to ‘bend’ in concert with the input surfaces. By bringing together the best of grid modelling, triangulation modelling, block modelling and grade estimation, the HARP model opens up many exciting new opportunities for the stratigraphic geologist or engineer to take their model further than was previously possible. Examples of improvements in modelling methodology using a HARP model include: the ability to represent complex normal, reverse and thrust faulting; the ability to store thousands of additional analytical, geotechnical or calculated variables in each individual block; advanced visualisation, manipulation and plotting capabilities; and the ability to calculate volumes and resources against complex, three-dimensional (3D) solid pit designs. Finally, several ‘real world’ scenarios, illustrating how this advancement in modelling technology can benefit a wide range of mining professionals are detailed. These examples demonstrate how productivity gains can be made in both long-term resource modelling and short-term ‘week by week’ geological modelling as an adjunct to mine planning.

Aug 22, 2011