Search Documents

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E Hondros

Innovation and Business Skills Australia (IBSA) commissioned The Boston Consulting Group (BCG) to undertake a study into how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. This report builds on a previous study prepared by BCG in the early 1990s for the Industry Taskforce on Leadership and Management Skills (Karpin Committee), which provided a snapshot of the Senior Manager in 2010. The following powerpoint slides summarise the 2020 Vision û The Manager of the 21st Century û outlining how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. The presentation is summed up in the following quote from Jon Nicholson û Senior Vice President of BCG: We believe that to succeed in the years up to 2020, executives will need to master a range of hard and soft skills. Amongst other things, they will require to manage multi-generaional teams, the creativity to measure staff performance on outputs rather than inputs, and a high degree of technical and functional expertise in addition to their general management credentials. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By P Wood, S Leveritt

This paper will introduce some innovative strategies for simulator training that are intended to improve the level of safety and operational performance of heavy equipment operators. The key strategy is to design simulator training to deliver improved work performance outcomes. This strategy is underpinned by a process for engaging workers in knowledge discovery and transfer that has been developed as an outcome of an Australian Coal Association Research Program (ACARP) funded project conducted at open cut coal mines in Australia. The process is expected to deliver improvements in the safety and operational performance of heavy equipment operators by informing training content about how experienced operators manage unexpected situations around the site. Tapping into the tacit knowledge that experienced operators gather over time can provide site specific and timely information about situational cues used to manage the unexpected. This type of information complements basic skills training by helping the trainee understand the operational context in which the acquired skills will be applied. Inexperienced operators have traditionally gained experience through their own actions, observing the actions of others and by taking the advice of mentors who have æbeen there, done thatÆ and developed operational decision making skills for safe and productive work performance. Leadership and mentoring techniques that contribute to effective knowledge delivery will also be discussed.Other simulator training strategies include refresher training, change management, emergency response training and testing the usability of new equipment and technologies prior to their introduction on-site. A key challenge ahead for the resources sector is the development of knowledge elicitation techniques that suit the operational workforce. A challenge for simulation and modelling professionals is to develop and refine techniques that support cost-effective customisation and regular updates of simulator scenarios.CITATION:Leveritt, S and Wood, P, 2012. Raising the simulator training bar - Strategies for improved work performance and effective utilisation of site-based simulators, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 65-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By I M. Platten, Y Xie, R-M F. Bell, S C. Dominy, L E. Howard, R C. A Minnitt

For any resource evaluation program, the collection and processing of representative samples for assaying is critical. Sampling, sample preparation and assay protocols must be designed to suit the style of orebody in question. The a priori need is for the characterisation of mineralisation type(s) and domain definition. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols employed. Mineralogical studies focusing on gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering and proportion of coarse versus fine gold. High-resolution X-ray computed tomography (HRXCT) is a radiographic technique that produces high-resolution 3D computerised models of in situ objects based on density distribution. The ævirtualÆ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ particles in coarse gold-bearing ore samples from the Nalunaq mine, southern Greenland. The samples used were previously well-characterised through mineralogical and metallurgical testing, and serve to test the HRXCT methodology. Gold particle size and distribution in the context of the sampling liberation diameter was investigated.CITATION:Dominy, S C, Platten, I M, Howard, L E, Xie, Y, Bell, R-M F and Minnitt, R C A, 2012. Determination of the sampling liberation diameter in a high-grade coarse gold ore by high-resolution x-ray computed tomography, in Proceedings Sampling 2012 , pp 161-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

By C McHugh, F Oppolzer, B Rogers, A Stokes

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation has more to do with improving the accuracy and consistency of mining processes and less to do with cost savings through labour reduction.A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation, ore loss and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio TintoÆs surface mines.This paper describes Rio TintoÆs multi-drill automation project, which has developed a robust system for automating most of the functions on several Caterpillar SKSS16 drill rigs. Automated drilling is currently being trialled in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the automated multi-drill system is given together with an overview of how automated drilling is performed remotely from the operating bench.A review of the performance and benefits of the automated multi-drill system is given together with future plans to extend the functionality of automated drills.CITATION:McHugh, C, Stokes, A, Oppolzer, F and Rogers, B, 2012. Automated multi-drills in Rio Tinto, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 83-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By R Bradford, W Gift-Agbey, T Vorster, P Morgan, E Grobler

The Asanko Gold Mine in Ghana started processing ore from the Nkran pit in January 2016 at a production nameplate of 3 Mt/a. The flowsheet is a conventional SAG, ball mill and pebble crusher (SABC) with gravity-gold and carbon-in-leach (CIL) recovery. The nameplate production was comfortably achieved within 3 months, so much so, that it was clear the SABC circuit was capable of processing more than the downstream section of the plant. Consequently, a program of de-bottlenecking was initiated to rectify volumetric capacity constraints. This program was later referred to as ‘Project 5 Million’ (t/a) or P5M. Having completed the de-bottlenecking exercise, it became evident that the SABC circuit could not reach 5 Mt/a solely on hard rock from Nkran. The new challenge was therefore to increase the capacity of the milling circuit through a focused comminution initiative that would address the following: geometallurgical treatment plan; upfront fragmentation requirements; installation of feed and mill monitoring equipment; and integration of a knowledge-based control strategy. This paper takes the reader through the various measures implemented to increase the milling rates and to create a stable/ sustainable control philosophy. As a result of the implementation of advanced mill performance monitoring technology (MillSlicer) and the collaboration between a team of experts in comminution, control and operations, the Asanko Gold Mine process plant feed tonnage has successfully increased from 3 Mt/a to 5 Mt/a.CITATION:Bradford, R, Gift-Agbey, W, Grobler, E, Morgan, P and Vorster, T, 2018. Optimisation of Asanko’s Obotan SABC circuit to achieve ‘Project 5 Million’, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Dyt, S Lyons

In the mining industry, crusher-related incidents have led to 15 reported deaths in Australia, New Zealand, and the USA between 1998 and 2007 (NSW Government Resources Regulator, 2024). The majority of these fatalities occurred during routine crusher maintenance tasks. A survey of quarry and mine site maintenance staff was completed to ascertain what they thought of such safety device to understand if beneficial and if so reasons if unused. Overall, findings show, staff perceived risks differently, cost, familiarity, device awareness and not front of mind, influenced adoption. This underscores the importance of asking the right questions involving maintenance and safety staff to lead to more proactive risk assessment.

Apr 16, 2024

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By J deVries, A Broodryk, P Kyselica, K McLean

Gwalia gold mine is located close to the town of Leonora in the Goldfields region of Western Australia, some 830 km from Perth. The mine is wholly owned by St Barbara Ltd, an Australian Securities Exchange listed gold producer and explorer. The Gwalia mine is a deep, all-trucking mine and is serviced by a 10 km long decline from surface. Mining is currently 1540 m below surface. Reserves extend to 1820 m below surface and are open at depth. The mine produces in excess of 200 koz of gold per annum.The Leonora area is hot and arid, with a mean annual rainfall of 230 mm and a 95 per cent mean daily maximum temperature of 20.3°C wet-bulb and 35.6°C dry-bulb.The primary ventilation system comprises a 490 kg/s surface exhaust fan, which draws air down a parallel intake system consisting of the decline, and a dedicated fresh-air intake system extending to the bottom of the production zone. Cooling is provided via a surface bulk air cooler serviced by an ammonia refrigeration plant that delivers 150 kg/s of chilled water to the bulk air cooler.The refrigeration plant and bulk air cooler were installed in 2008. The design allows cooling to be increased over time by installing an additional refrigeration plant in a lead lag configuration with the current refrigeration plant when required.Since 2008, expansion and increased depth reached a point where the underground heat load exceeded the installed capacity of the existing 4.0 megawatt rated (MWR) refrigeration plant. In order to maintain the mine design conditions underground, upgrading of the existing refrigeration system was required to bring the cooling capacity to 7.5 MWR.Two expansion options were considered: the addition of an ammonia vapour-compression refrigeration machine similar to the existing one or a lithium bromide absorption refrigeration system using waste heat from the site power station. The original design and layout of equipment on-site meant that either could be used, allowing an assessment of the merits of both when additional cooling was required.The decision was made to install a lithium bromide absorption system on the lead side of the existing ammonia refrigeration plant. This arrangement provides considerable economic benefits, including reductions in site-generated electrical power, generator fuel consumption and carbon dioxide emissions.This paper details the planning, design, installation and commissioning of the absorption chillers.CITATION:Broodryk, A, deVries, J, Kyselica, P and McLean, K, 2015. The design, installation and commissioning of an absorption refrigeration system at Gwalia gold mine in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B W. Atkinson

Full-stream mechanised sampling apparatus, that collect a full cross-sectional increment from the complete screen discharge, will always be the preferred option for sampling screen overflows. However, the reality is that provisions for automated sampling are rarely, if ever, provided at the discharges of individual screens within beneficiation plants.Sampling from the discharge of high capacity vibrating screens, especially multi-slope screens, is subject to sampling bias, due to the stratification of the ore that occurs on the vibrating screen deck. The stratification in the vibrating bed translates to a stratified falling stream at the discharge end of the screen, typically with smaller particles at the back of the falling stream and large particles at the front of the falling stream (Figure 1).The chemical and physical characteristics of heterogeneous ore (mineral or coal) particles vary significantly with particle size. If samples do not correctly reflect the source material size distribution, they will be biased and the resulting analytical/assay data will not reflect the actual physical nor chemical characteristics of the source material.Prior published data for coal preparation research (Australian Coal Association Research Program) has demonstrated that a bias appears to exist for samples collected from high capacity multi-slope screens.A new form of sampling scoop has been developed with the aim of overcoming this issue.Bias was evaluated at a coal preparation plant by comparing the desliming screen overflow size distribution to that for æreferenceÆ coal preparation plant feed samples collected using the recognised stopped-belt technique. The study procured 20 sets of comparison samples in order to ensure statistical relevance.Two forms of sampling device were employed for the multislope screen discharge.A conventional square aperture scoop was demonstrated to exhibit a significant coarse bias, in that the resulting samples exhibited a significantly coarser size distribution compared to the reference samples. In other words it was evident that the conventional scoop æfavouredÆ material from the front of the falling stream.A new æcollapsibleÆ sample scoop was evaluated in parallel, and its samples were found to exhibit no relevant bias.CITATION:Atkinson, B W and Swanson, A R, 2012. A new method for sampling from high capacity screens, in Proceedings Sampling 2012 , pp 89-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By K J. Ward, C N. Hatton, J Scalia IV, C A. Bareither, D L. Spencer

The mining industry is experiencing change in the governance of tailings facilities (TFs). Guidance and regulations across many jurisdictions contribute to this amorphous change. The Canadian Dam Association, Mining Association of Canada, Australian National Committee on Large Dams, and the Global Industry Standard on Tailings Management, produced by the International Council on Mining and Metals, are establishing guidelines for more rigorous industry governance. Evolving guidance regarding TFs is developing concurrently with a shortage of experienced tailings engineers, which adversely affects the resource base available to support new governance. This paper presents an updated semi-quantitative estimate of the impending resource shortage of qualified tailings professionals. Updates are provided herein for the estimated number of TFs worldwide, which included available data on active and inactive TFs, as well as the estimated labor resources required to service these facilities. The tailings labor shortage is discussed in the context of academic and professional training currently available to increase the quantity of trained personnel. This paper represents a discrete moment in time as contributions to the available information and inventories accessed continue to improve, but as of today are incomplete. However, the data and information included provide insight into the resource deficiencies currently within our profession, training and education opportunities to address those resource deficiencies, and a snapshot of a recent professional training course offered on mine tailings.

Jul 1, 2021

By T Walton, C Perring, M Pepper, G Gerber

The Yandicoogina Channel Iron Deposit (CID) is an accumulation of iron pisolites cemented by a goethite-rich matrix. The Yandicoogina CID’s are found in a palaeochannel that meanders within a broad structural basin of the Yandicoogina Syncline in Pilbara region of Western Australia. RTIO Yandicoogina Mine Geology team contributed to a number of strategies maximising the iron ore reserves mined by Rio Tinto. Two strategies are discussed: the replacement of the Batter-Berm final pit walls by contour dozing; and upgrading the lower grade material to crusher feed. 1. Contour dozing – traditional Batter-Berm pit final wall configuration left kilometre long wedges of ore sterilised around bench margins. Contour dozing final walls (ie dozing of ore down the ore-waste contact) as internally defined by RTIO Yandicoogina Mine Geology (Mine Geology), enabled recovery of additional crusher feed. 2. Upgrade of lower grade material – the lower ore domain (GVL) within the Yandicoogina orebody contains numerous clay pods. Contaminant Al2O3 inherent within clay pods can result in CID material outside of crusher feed grade specifications, causing it to be flagged as ‘internal waste’ in mining models and permanently lost to waste dumps. In 2011, after multiple tests, Mine Geology demonstrated that this material could be upgraded to crusher feed via wet processing. With the support of the RTIO Metallurgical Development team new grade specifications were defined. The resulting material has been used to supplement higher grade ore. While increasing the mining ore output, these ongoing value-adding strategies also promote more sustainable mining via better use of the non-renewable iron ore commodity. The initiatives extend mine life, reduce waste movement, improve strip ratio and increase productivity

Mar 22, 2022

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

The Newcrest Mining Limited Telfer Gold Mine consists of an underground sublevel cave (SLC) operation located 734 m directly below active open pit operations. Open pit and underground current production rates are 50 million and 5.7 million tonnes per anum (Mt/a) respectively. The SLC was initiated in late 2006 with breakthrough planned to occur on the 5484 bench of the west wall in late 2009. Risk to the south ramp was identified during this time, resulting in the construction of the north ramp. The SLC was continually tracked from initiation with a suite of monitoring systems and managed with a Major Hazard Management Plan (MHMP) and associated Trigger Action and Response Plans (TARP). At breakthrough the eastern limb of the cave was located within a 70 m horizontal distance from the south ramp. The south ramp was closed in October 2009 due to significant slope deformation, extensive cracking in the berms and batters between the ramp and breakthrough bench and a major failure 250 m to the north of the cave breakthrough. Wall response was first identified from slope deformation measurements taken by the wall monitoring radar in May 2009, at which point the SLC was 160 m from breakthrough. The impact of the SLC on the slope is a unique case with the monitoring systems in place able to provide data on the slope reaction to the SLC progression. This paper will discuss the management of the south ramp such as the early interpretation of risk associated with cave breakthrough, monitoring systems implemented to track the cave progression and wall deformation, data integration and interpretation and risk management. Following the closure of the south ramp further instrumentation programs and risk assessments were conducted to determine the risk of re-opening this haulage route. The outcomes of this program will also be presented.

Nov 25, 2010

By R L. Brathwaite, R Carver

The REGCHEM (Regional Exploration Geochemistry) database of open file mining company data, managed by GNS Science, has recently been upgraded with the compilation of additional data, especially for the Otago region (see http://maps.gns.cri.nz/website/minmap). In June 2007, data compiled for the Otago region included more than 2000 stream sediment samples from 19 surveys, more than 800 BLEG (bulk leach extractible gold) samples from 12 surveys and a few pan concentrate samples. The stream sediment samples were typically analysed for Au and As, and in many cases for other elements including Cu, Pb, Zn, Sb, W and Mo. The BLEG samples were analysed for Au and in some cases also for As. The main exploration target was mesothermal gold deposits in the Otago Schist, although one survey of the Otago Peninsula targeted potential gold deposits associated with the Dunedin volcanic complex. Geochemically, the mesothermal gold deposits are characterised by anomalous As and Au, with some also characterised by anomalous W and Sb, and these four elements are the best pathfinders in stream sediment geochemical surveys. The introduction of lower detection limits in Au analyses in the more recent stream sediment surveys and in the BLEG surveys enables the use of this element as the primary pathfinder for mesothermal gold deposits.

Jan 1, 2007