Search Documents

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By J Skousen, C E. Zipper

"Prior to the 1950s in the USA, surface coalmines were generally left without any reclamation. As government regulations advanced, mine operators were required to backfill the area and plant grasses or trees. After the federal Surface Mining Control and Reclamation Act (SMCRA) was passed in 1977 in the USA, mine operators were required to conduct pre-mining analyses of the site and to designate a land use that could be achieved after the mining. Common post-mining land uses in the USA are: agricultural uses such as prime farmland reclamation with crops, hayland and pasture, and biofuel crops forestry wildlife habitat building site development.Provisions and regulations for each post-mining land use were developed and practices to achieve successful and sustainable land uses were established. Post-mining conditions should provide ecosystem services and produce lands capable of supporting societal needs in the future.CITATION:Skousen, J and Zipper, C?E,?2014. Post-mining land use options in the Appalachian coal mining region of the USA, in Proceedings Life-of-Mine 2014, pp 153–164 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By F Shi, G Ballantyne, K Runge

There has been minimal innovation in the methods used to process an ore over the last 50 years. Productivity increases have largely resulted in increased equipment size without implementation of parallel improvements in technology. Complex orebodies of the future will need mining operations to adopt new technologies and techniques to make future ore treatment economically viable. Three emerging technologies, namely high voltage pulse (HVP) pretreatment, fine screening and the HydroFloat<sub>TM</sub> coarse particle flotation cell will be presented in this paper and the potential benefits that may result if they are adopted in mineral processing circuits will be outlined. The barriers that must be overcome before they can be adopted by industry with confidence will also be discussed. CITATION: Runge, K, Shi, F and Ballantyne, G, 2018. New technologies that will potentially enable processing of complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 126–129 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Since 1969, a substantial number of geophysical methods have been applied in the search for porphyry copper and mesothermal type -sulpha-de deposits. These have assisted with geological mapping as well as the definition of various sulphide depos-its. The application of these methods at the Frieda-Nena deposits, Papua New Guinea, can be used as a case study for exploration in other parts of New Guinea.In 1993, Highlands Gold Limited carried out an intensive geophysical program over the Nena deposit. The methods employed included, CSAMT (controlled-source audio magneto-tellurics), airborne and ground elect-romagnetics, IP/resistivity and ground magnetics. The magnetic method was used as a regional mapping tool as well as a way of mapping alteration zones over both the Nena and Frieda River copper deposits. Electromagnetics, in part-icular FLAIRTEM, is a rapid reconn-aissance tool as well as a detailed mapping tool for the location of Nena-style massive sulphide deposits. IP/ resistivity is an expensive but most useful tool for mapping out Frieda porphyry copper style disseminated sulphides as well as Nena style deposits. It can be used to define drill targets in areas of difficult Access.a

Jan 1, 1994

By M Matheson

Increasingly, owners and operators of underground mines that have a long history are realising the economic and practical advantages of capturing historic mining records and converting hand drafted plans of underground mine workings into an electronic collection of attributed 3D wireframes that can be used for mine planning and exploration purposes. This case study looks at the conversion of historic data to 3D models, with examples from three historic mining operations where this task has been undertaken: West Wits gold projects in South Africa, Northern MiningÆs Radzimowice gold mine in Poland and Avalon ResourcesÆ Viscaria copper mine in Sweden. West Wits Mining Limited holds leases in the West Rand Goldfield of the Witwatersrand Basin, which has significant gold and uranium resources that have been mined since the 1890s. The Radzimowice Gold mine, Poland, hosts Au-Cu-As-Ag mineralisation that has been exploited since the 15th to 16th centuries. The Viscaria Copper mine is located in northern Sweden and was operational during a 15 year mining period to 1997. The process of data collection, management and modelling is inherently challenging for these mines; specifically, collation of historical information, organising this data into logical arrangements that could be validated and sequentially creating 3D models using geo-spatial computer software. Despite the challenges and costs involved in creating a digital 3D model, the conversion has added significant value to each project through identifying areas of potential new resources, aiding planning and presentation to stakeholders. This paper outlines the processes involved in conversion from paper records to a 3D model, the challenges encountered and how these can be overcome, and importantly, the practical and economic advantages of undertaking such a task for explorers, miners and investors.

Jan 1, 2009

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

By P Jonsén, S Larsson, M Parian, B I. Pålsson

The question of effective energy utilisation in grinding mills is not new. There are several conflicting arguments about tumbling mills, whether the efficiency is around 1 per cent or maybe 10 per cent, or even much lower. The energy not used is assumed to be lost as heating of the pulp, the grinding mill body, the charge, generation of shock waves and vibrations, etc. Stirred media mills on the other hand are generally considered to have better energy utilisation, but their energy efficiency is still not that clear. To shed some light on this a pilot-scale, wet stirred media mill was investigated over a range of operating conditions. The wet stirred media mill is a Drais PMH 5 TEX pearl mill fitted with an electric motor at 11 kW. It has been investigated over a range of operating conditions to try to balance the dissemination of the input energy in forms of the net grinding energy, mechanical energy losses, and the heating transferred to the pulp, the mill, the charge, and the cooling water. It is found that approximately 20–40 per cent of the input energy accounts for the grinding process. Also, that the difference between gross and net input electrical energy is mainly disseminated as heating of the pulp and cooling water. Mechanical energy losses appear to be much smaller than the heating effects. The use of a dispersant seems to mainly influence the heating effect.

Aug 24, 2022

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

For over 50 years R W Miller & Co Pty Ltd operated old coal properties abandoned by former owners as uneconomic, some of which dated back to the last century. The companyÆs ability to survive with what were relatively poor quality coal resources required a small efficient management organisation. In 1970 R W Miller was involved in negotiations with other coal companies through coal sales contracts to develop private coal areas under the provisions of the old Coal Mining Act (1906) and these efforts led to the development of Lemington colliery. At the same time development of the Ironbark colliery holding near Newcastle commenced. In 1971, R W Miller approached the New South Wales Government for a resource replacement area to prospect for coal in the Upper Hunter Valley. Authorisation No 33 was finally granted on 30 September 1975, but the company found the area was inaccessible as most of the surface was owned by the Australian Army. Later R W Miller was granted Authorisation 66 of 2167.5 hectares at Mount Thorley near Singleton on 1 November 1976. The development of this coal mining project coincided with the second OPEC oil crisis in 1978 and a short-term boom for coal resources and the unrealistic expectations generated by the boom. This paper gives a broad outline of the development of the Mount Thorley project between 1976 to 1986 including the feasibility study and the many governmental and industrial delays that resulted in a three-year time overrun in the project development period.

Jan 1, 1998

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

The ores described in this paper are from the two principal orebodies at Wiseman's Creek, a small village about 22 miles south-east of Bathurst in central-western New South Wales.The first official reference to mining at Wiseman's Creek is in "Mineral Statistics of New South Wales" of 1875, which reported that the Wiseman's Creek Copper Mining Company had proved a lode-later known as "North Wiseman's"-to a depth of 120 ft., where it was found to be 20 ft. wide. By 1876 the erection of a mill and smelting works had commenced, and the sulphide ore found to contain copper lead, zinc, silver and gold. Some oxidised ore was also being worked. Operations were, however, generally unsuccessful, and sporadic work up until 1907 produced only about 5,000 tons of ore. The other more important orebody of the locality-the Phoenix-was not opened until about 1895. By 1908, as reported by J. E. Carne, the shaft had been sunk 340 ft., with the extraction of both oxidised and primary ore. At the time of the slump in copper, pric'es in 1907 approximately 3,000 tons of, ore had been produced.Several smaller orebodies were discovered and worked during the same period as the North Wiseman's and Phoenix, but their output was more or less insignficant. THE OREBODIES AND THEIR GEOLOGICAL SETTINGIt is now impossible to examine the orebodies underground, but they appear to have formed a series of flat lenses, whose major axes were parallel to ,the foliation of the enclosing quartz-chlorite-muscovite schists. The largest ,of these lenses was worked as the North Wiseman's orebody, which was reported by Carne to vary in width from 1 ft. to 20 ft., and which probably extended discontinuously over a strike length of about 1,000 ft. The Phoenix orebody is stated to have varied from 1 ft. 6 in. to 3 ft. in width...

Jan 1, 1955

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By Butler I. K, Nicholson P. M

There are four main types of base metal and gold mineralisation recognised in the central Pine Creek Geosyncline. These are stratiform, polymetallic veins, stockwork/concordant gold-quartz veins and unconformity related uranium-gold-platinoid mineralisation. The stratigraphy of the central Palaeoproterozoic Pine Creek Geosyncline has been simplified into three groups comprising the Batchelor, Frances Creek and Finniss River Groups in ascending order. Stratiform mineralisation occurs within the Frances Creek Group. The earliest mineralisation is found adjacent to circular faults ringing basement highs. Higher in the stratigraphy, stratiform mineralisation is often associated with zones of high compression in the vicinity of basement highs. A synsedimentary-diagenetic origin for stratiform mineralisation is proposed. Polymetallic vein mineralisation occurs within the Frances Creek and Finniss River Groups. Its composition changes systematically through the stratigraphy similar to the stratiform mineralisation. The mineralisation is structurally controlled and usually occurs in the vicinity of basement highs. Stockwork-concordant gold-quartz vein mineralisation is hosted by the upper Frances Creek and Finniss River Groups. It occurs within compressional zones and along the Pine Creek Structure corridor around, above and particularly between basement highs. Mineable reserves occur in thick continuous semi concordant quartz-sulphide veins and/or stockworks. Unconformity related uranium-gold-platinoid mineralisation shows a close spatial relationship with the Palaeoproterozoic/Mesoproterozoic unconformity. The mineralisation is localised by structures formed during Mesoproterozoic deposition and is commonly adjacent to Archaean basement or its remobilised equivalents. The type of mineralisation (stratifom/polymetallic vein) is a reflection of local stress regimes, structure and physio-chemical conditions. An initial phase of stratiform mineralisation is postulated to have occurred with the first significant marine transgression in a tensional regime. A second phase occurred later during a compressive regime. "Ihermochemical sulphate reduction of mineralising fluids by hydrocarbons is invoked as the precipitation mechanism for the polymetallic vein type of mineralisation. Hydrocarbon generation is postulated to have occurred within the Frances Creek Group, in many places contemporaneously with the movement of mineralising fluids and basin compression. Polymetallic veins formed from the interaction of mineralising fluids and hydrocarbons which were trapped in suitable structures. An abundant, continuing supply of hydrocarbons was necessary to form significant deposits. Where these conditions were not net, the mineralising fluids largely continued their ascent to the near surface environment to form stratiform deposits. The stockwork/concordant gold-quartz vein mineralisation is a later event and occurred during the relaxation of compressional defonnation after deposition of the 1-inniss River Group.

Jan 1, 1994

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices andoptimisation of the mining method to suit the mining environment.Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave.Prior to the implementation of bulk emulsions an investigation wasrequired to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999

By G York

South African gold reserves extend to great depths. However, strategies for the mining of such deposits have changed only slightly over the past number of years. Regional support at depth is currently provided by rock pillars and backfill. Many problems have been experienced with these regional support practices at deeper levels. In this paper several alternative forms of regional support are described which include the use of concrete, the use of back area caving and confinement to strengthen pillars. These new concepts are supported by numerical and laboratory modelling and in situ results.

Jan 1, 1998

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices and optimisation of the mining method to suit the mining environment. Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave. Prior to the implementation of bulk emulsions an investigation was required to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999