Search Documents

By W. H. Nielson, L. S. Diaz

Several techniques are presented to adjust small errors inherent in data collected from material balance measurements on the flotation process. The basic technique used is a Lagrange multiplier adjustment of the filtered data taken from the equipment measurements. The raw data are adjusted such that material balances are closed. The adjustments to each data point is inversely proportional to the square of the standard error of measurement. Problem areas in equipment utilization are discussed. Typical results from on-line measurements are presented. This technique can be applied to either on-line process measurements or metallurgical test data.

Jan 1, 1973

By Verne D. Johnston

ALTHOUGH the stocks of Lake Superior iron ore on dock or at furnaces at the beginning of the year were about 6,000,000 tons less than at the beginning of 1938, the steel industry was operating at only 52 1/2 per cent of capacity and continued at approximately this rate to about Aug. 1. Consequently the iron mines in the Lake Superior district during the winter and spring period were almost all on a curtailed production basis, governed mostly by the needs of the communities rather than by anticipation of ore demands. Many of these properties gave extra employment by prosecuting heavy strip- ping programs, and the underground mines by shaft sinking and rock development. All underground mines re- turned to full operation in September, mostly two-shift, five days per week. A few operated the sixth day. The ship- ping schedules were increased so that the actual delivery for the year exceeded early expectations by about 20 per cent. Final Lake shipments were slightly in excess of 45,000,000 gross tons.

Jan 1, 1940

By D. O. Wyble, L. O. Bacon

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By L. O. Bacon, D. O. Wyble

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By AIME AIME

IN an address before the New York Section. A.I.M.E., Oct. 20, Alex L. ter Braake, speaking on the tin industry of the Netherlands East Indies, interjected a few remarks, at the chairman's request. on the mineral stock-piling project now before Congress in a bill sponsored by Senator Scrugham. The full text of Mr. ter Braake's paper was published in the Nov. 6 issue of the American Metal Market. Following mention of the buffer stock scheme as applied in the tin industry, Mr. ter Braake continued:

Jan 1, 1943

By Leonard D. Jaffe

IN recent years, the advantages of tempered martensite as a microstructure for steel parts have been well established. For parts that must not fracture brittlely when loaded at high rates, at low temperatures, or under conditions of combined stress, tempered martensite is especially desirable. One of the factors that determine whether a steel part will have a martensitic structure after heat treatment is the hardenability of the steel. Despite the large amount of recent research, there are still many unsettled basic questions concerning hardenability and its relation to chemical composition, and, indeed, considerable disagreement among investigators in the field. Much of the uncertainty that beclouds the existing knowledge of hardenability arises from the fact that hardenability is still a wholly empirical concept, and has not been quantitatively related to the more fundamental knowledge of isothermal decomposition of austenite. Hardenability is, essentially, a measure of the time required for small percentages of austenite to decompose, during continuous cooling, to pearlite, bainite, proeutectoid ferrite, or proeutectoid carbide. In the practical heat-treatment of steel, also, the decomposition of austenite is usually not isothermal but rather during cooling, or, in general, is not at a single constant temperature. Thus, both hardenability and practical heat treatment involve anisothermal decomposition of austenite. In a previous publication1 the author and his collaborators outlined the principles that govern the relations between isothermal and anisothermal decomposition of austenite, and reviewed the experimental information available in 1945. To avoid repetition, familiarity with that article (Paper 1) will be assumed, and attention given primarily to work carried out or published since 1945. The method generally employed was explained in Paper 1: anisothermal transformation is studied through investigation of the effect of holding austenite at one temperature upon its subsequent decomposition at another temperature. Both temperatures are below the stability range of the austenite. This paper is confined to studies in which only a small amount of transformation occurred at the first temperature. This is the only case of importance in practical heat treatment when an essentially martensitic structure is sought. MATERIALS AND PROCEDURE It was necessary to use different steels for the studies involving proeutectoid ferrite and for those involving proeutectoid carbide, because the two constituents have not been found to form in the same steel. Several steels were tried and rejected

Jan 1, 1947

By DIFTIGIHT E. WOODBRIDGE

(Glen Summit Meeting, June, 1911,) DURING April, May, and June, 1910, I was in charge of an examination of the greater part of the Moa iron-ore area in Oriente Province, Cuba, on the north coast, near the east end of the island. My instructions, on arrival at the properties, were to check former estimates of tonnages and grades, and to re-examine the ore comprised in claims covering 44,727 acres. This work included .the running of lines dividing the properties into co-ordinate planes, the boring of many thousand feet of holes spaced at the intersections of these co-ordinates, the taking of samples of the ore penetrated, the analysis of these samples for their various constituent minerals, and the determination of the results as to tonnages, depths, and grades, both for individual properties and for the entire group. Each section of every one of the thousand holes drilled was to be compensated for depth and grade with every other, a series of simple arithmetical calculations of no slight magnitude, the mere mechanical labor of which consumed much time, but finally resulted in giving a complete average of all the essential facts for the entire area of 18,000 hectares. Had it not been for the more than willing, active, and able co-operation of the officers of the Spanish-American Iron Co., from Charles F. Rand, President, and Jennings S. Cox, General Manager, down to the most humble water-carrier, the work would have consumed far more time than it did. Papers prepared by others, and to which my present paper may be considered an addendum, elucidate, more fully than I could hope to do, the origin and geological character of these ores. I will confine myself to the situation, method and expense of exploration, and to probable courses of development and mining, with some attention to the cost of the ore delivered in the United States.

Mar 1, 1911

By W. F. Hosford

A quantitative explanation is offered for the peculiar curled grain shapes found in the microstructures of drawn wires of bcc metals and compressed aluminum specimens. It is shown that once an [011] fiber texture is developed, the slip system are so oriented that further slip tends to produce plane strain rather than axially symmetric flow of individual grains. With plane -strain flow, however, compatibility of neighboring grains can be maintained only by a bending of grains about one another. PROBABLY the most obvious microstructural feature of heavily worked metals is the distorted shapes of grains. In the course of deformation, the shape change of each grain must be compatible with that of neighboring grains; otherwise holes would be formed at grain boundaries. In analyses of poly-crystalline deformation by Taylor and subsequent workers it was assumed that grain boundary compatability was maintained by each grain undergoing the same shape change as the polycrystalline aggregate in which it is imbedded. According to this assumption, when simple tension or compression is applied to a random polycrystal or to one with a fiber texture, each grain ought to deform with axially symmetric flow. Initially equiaxed grains should become cigar-shaped during wire drawing and pancake-shaped during compression. While microstructural observations of deformed metals are generally in accord with such a picture, certain striking exceptions may be noted. Peck and Thomas5'8 found that grains in heavily drawn tungsten, iron, and niobium (columbium) wires become shaped like ribbons curled about the wire axis, Fig. 1. At a suggestion from the author, they rationalized the development of these micro-structures by considering the orientation of the slip systems in the [011] texture formed by the wire drawing. It is shown in this paper that marked departure from axially symmetric flow of grains is also observed when polycrystalline aluminum is severely compressed. Again the explanation must lie in the orientation of the slip system in the [011] texture, which is formed in fcc metals by compression.' THEORY A simple quantitative argument will be presented to show that the development of these microstructures is a result of flow on the combination of slip systems for which the minimum amount of mechanical work is expended in producing a unit tensile (or compressive) strain. First it must be realized that the macroscopic strains of a crystal resulting from slip are given by: where d dy, and dc, are normal strain increments parallel to the x, y, and z reference axes; are crystallographic shear-strain increments on slip systems

Jan 1, 1964

By R. E. Miner, J. K. Jackson, T. L. Wilson

A study has been made of the transformation kintetics and morphology in gas-quenched Fe-5 pct Ni alloys. Massive ferrite or nlurtensite was found to form at temperatures in agreement with earlier results. Surface Preparation appeared to have the greatest effect in determining the type of transformation Product formed. Grain size change, subgrain morphology, and dislocation densities of massive ferrite were essen-tinlly invariant functions of cooling rate. The mar-tens~tic structures were typical of transformation in austenite grains of the order of the sample thickness. BY introducing the idea of a massive transformation in dilute iron-base alloys, Gilbert and Owen in 1962 served to stimulate a closer inspection of phase transformations in ferrous systems.' A wealth of literature has followed concerned with the morphology,2-5 transformation mode,2'3'6-8 and thermodynamics of transformations.2,5,9 interesting controversies have resulted from the experimental observations; closer attention has been paid to the definition of massive transformations and still to be resolved is the Ms temperature of pure iron. The purpose of this note is to report some observations made in a detailed kinetic and metallographic examination of the transformations that occur in gas quenched Fe-5 pct Ni. The results are pertinent to the Ms extrapolations that have been made for pure iron and the observed substructure of massively transformed alloys. PROCEDURE The material used in this investigation was cast as a 5 lb vacuum induction melted, carbon deoxidized heat. The ingot was hot worked to a strip 0.10 in. thick, decarburized, and cold rolled to final thickness. Specimens were punched to sample shape and decarburized in wet hydrogen at 600°C. The chemistry of test specimens is indicated in Table I. Samples 1 by $ in., by thickness were resistance heated and rapidly cooled in an apparatus as illustrated in Fig. 1. Similar helium quenching apparatuses have been described previously;2,6'10 the distinguishing feature of this apparatus is the nozzle geometry. Twin nozzles with three convergent-divergent, sonic ports were mounted perpendicular to the specimen for quenching purposes. The specimen temperature was monitored with an intrinsic 3 mil chromel-alumel thermocouple spot welded to the specimen and con- nected to an oscilloscope. A single switch stopped the current flow through the specimen, opened a gas flow solenoid valve, and initiated an oscilloscope sweep. Cooling rates were read directly from a photograph of the oscilloscope trace and the quenching rates quoted later were made at a point immediately prior to transformation on the trace. All quenching studies were conducted either under a vacuum of 10"-5 torr or a helium atmosphere. The sample geometry was chosen large enough to permit optical and electron microscopy to be performed on samples. The samples were electropolished for both types of examination in a perchloric-acetic solution. Electron microscopy was conducted on a HU 11A microscope operated at 100 kv. Dislocation densities were determined at the same general operating reflection (110) on foils thick enough to produce Kikuchi patterns. RESULTS AND DISCUSSION Transformation Temperature Observations and OD-tical Microscopy. The quenching results of this study are illustrated in Fig. -2(a). Samples which were treated in the as-decarburized condition transformed in a manner similar to that reported previously—a decrease in transformation temperature occurred as the quenching rate increased until a plateau region was reached. Within the scatter of the results obtained here, there was no break in the transformation temperature-quenching rate plot. This suggests no change in transformation mode. Further metallographic examination confirmed this observation. A martensitic transformation was obtained for similarly treated samples except that the surface was first electropolished. The Ms temperature was approximately 85°C below the plateau determined for the unpolished samples and cooling rates as slow as 2000°C per sec were adequate for producing marten-site. The transformation temperatures are in gen- / STRIP SAMPLE / COPPER I SAX/-/}' / CONNECTOR-----A f, SON|C poRTS AC LEADS 3j ]j"I rofe[ \ Mf/yinK/iKj''^ THERMOCOUPLE X-(^—iie"s*c? ' LEADS 1 INCH Fig. 1-—Schematic scction of gas quenching apparatus

Jan 1, 1970

By C. R. Kyle, R. L. Perrine

A transparent model of a reservoir has been used to study some characteristics of instability in miscible displacement. The linear model dimensions are 1/4 in. x 91/2 in. x 10 ft. The model is packed with spherical glass beads. Thee groups of experiments have been performed. The objectives were to measure, respectively, the rate of growth of the transition zone, flow velocity variations in the transition zone, and the effect of a graded viscosity zone on stability. All experiments were compared, where possible, with theory. The transition zone grew almost linearly with distance traveled, regardless of flow rate, where adverse viscosity ratios were used. At very adverse viscosity ratios and large distances traveled, some reduction below linear growth was noted. This could be attributed to the effects of mixing. General similarity in flow pattern was commonly shown in different tests, although exceptions occurred at the higher viscosity ratios. Injection of tracer spots permitted direct experimental measurement of velocity variations. Statistical methods were used to compare observed velocity variations with recently published theories. Surprisingly good agreement with some theoretical predictions was obtained. In the experiments using an initially graded viscosity zone, macroscopic stability was reached before predicted by theory. Under conditions theoretically considered to be slightly unstable, any fingering tendency was too slight to become observable within a 10-ft long system. The general correlation of all experiments with published theory was good, and suggests that theoretical predictions can be extended to reservoir problems. INTRODUCTION Early laboratory studies of miscible displacement demonstrated the high recovery efficiency possible with this method. Linear laboratory models showed that, under some circumstances, all in-place hydrocarbons could be recovered using as little solvent as 5 per cent of the pore volume. These results led to a series of pilot field projects. Under realistic conditions, however, other laboratory studies showed that a small solvent bank may not recover much more oil than a conventional gas drive. The cause of this lack of efficiency is unstable viscous fingering. The size of the solvent bank required to give optimum recovery is, therefore, a question of great economic significance. The object of the experiments described in this paper was the quantitative measurement of unstable flow parameters, the verification of present theories on the miscible displacement process, and correlation of these theories with ex peri mental observation. Of the theories which have been advanced, those by Dougherty, Koval and Perrine show promise of predicting reservoir performance with reasonable accuracy.l-7 The present experiments were correlated, where possible, with the theories of Koval and Perrine. Dougherty's theory was not used because of the additional computational difficulty it presented and the belief that no further information would result. EXPERIMENTAL EQUIPMENT A transparent reservoir model, consisting of a vertical reinforced plexiglass column, was used for the experiments. The column was packed with glass beads, which served as the porous medium. To induce a known velocity disturbance in the flow, a double cosine wave restriction in the transverse cross-section was placed at the top of the column. To mark the flow field and provide a means of measuring the local fluid velocity, a dye-spot injection system was provided. The column was 10 ft high by 1/2 in. wide by 1/4 in. deep. The cosine restriction was placed 16 in. from the top of the column. The glass beads were smooth and spherical and had a mean diameter of 0.0102 cm. Liquids entered the top of the column through a manifold allowing three points of entry (left, center, and right, or any combination of these). A positive-displacement pump with variable-speed drive was used to control liquid flow rates. The pump transferred viscous oil from a reservoir to an accumulator, which displaced the test liquid into

Jan 1, 1966

By Shiou-Chuan Sun

SHIOU-CHUAN SUN (author's reply).-Thanks are extended to Professor Hassialis for his recognition of the usefulness of a new tool, the cataphoretic cell, as an adjunct to the bubble machine and the abstraction test. His questions concerning adsorption, dielectric constant, floatability, activation, and depression are interesting and worthy of discussion. I According to Mueller,28 it is questionable that any of the present formulas gives absolute values of zeta potentials which are completely accurate. The problem is further complicated by the question" of whether the "dielectric constant" has any meaning at all for such a microscopically thin layer. With these in mind, the results in this paper should be considered in the relative sense as a first approximation and not as absolute quantities. Adsorption Referring to item a of Fig. 8, the dielectric constant and the viscosity of the xanthate solutions are the same for galena, sphalerite and quartz. If dielectric constant and viscosity (but not the adsorption) were the first-order variable of the cataphoretic system, as claimed by Professor Hassialis, then the magnitudes of zeta coefficient of galena, spha)erite and quartz would have been similar to each other. These are not. The big difference of zeta coefficient of these three minerals in the same xanthate solutions is not altogether unjustified to be attributed to their difference in adsorption of xanthate ions. This is supported by the results of chemical abstraction tests reported by Ince.14 Again, the big difference of zeta coefficient between wollastonite, calcite, and fluorite in the same laurylamine hydrochloride solutions (p. 118, Figs. 58, 59, and 60 of ref. r5) also indicates that the cataphoretic system is not governed chiefly by the dielectric constant. Beside the data shown in Fig. 8, other experimental evidences15 which support the idea of correlation between adsorption and zeta coefficient are: (I) there is a qualitative parallelism between the zeta coefficient curve and the chemical abstraction curve of sphalerite in solutions of various concentrations of sodium cyanide, (2) there is a qualitative parallelism between the zeta coefficient curve and the chemical abstraction curve of sphalerite in solutions of constant concentration of copper sulphate at different pH values, and (3) there is a qualitative parallelism between zeta coefficient curve and chemical abstraction curve of quartz in solutions with constant concentration of barium chloride at different pH values. The above mentioned experimental results are generally in agreement with Gouy's double layer theory,1-5 and support this idea that the concentration and the kind of ions adsorbed at the mineral surface and in the adjacent surrounding liquid chiefly govern the electrokinetic phenomena. Dielectric constant and viscosity of the liquid medium may be of somewhat lesser importance. It follows that the correlation between the coefficient and adsorption as claimed in this paper is justified. Dielectric Constant The term "dielectric constant " was first introduced into the electrokinetic equations by Perrin.30 In a footnote of his publication he states that Holmheltz has forgotten to include the dielectric constant. The conversion of the moment29 to the zeta potential involves an additional difficulty and confusion not involved for the moment, namely, assigning a value to the dielectric coefficient. This is conventionally assumed to be constant and equal to the dielectric constant of the bulk liquid. 21 The published literature 10, 12 indicates that the values of dielectric constant for dilute chemical solutions have been assumed as those of pure water.

Jan 1, 1947

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

By AIME AIME

CHARLIE WARNER, Chairman of the Petroleum Division, is no stranger to the problems of the oil industry or to those of the Petroleum Division, after more than 25 years of experience in locating and producing oil and more than 22 years of membership in the Institute. He was born at Jefferson, N. Y.. April 27, 1894, and educated in the public schools of New York State and at Cornell University where he studied geology and allied sciences from 1913 to 1917 and received a B.A. degree. Immediately upon completion of this training, he was employed by the Empire Gas & Fuel Co. as a field geologist in Oklahoma and Kansas. Two years later he became district geologist for the Emerald Oil Co. in Oklahoma and Kansas, and in 1920 he rejoined the Empire Gas & Fuel Co. in the capacity of district geologist in Oklahoma. In September of 1921 he began his association with the Houston Oil Co. of Texas. He was district manager for the company in the Mid-Continent area until 1932 when he was transferred to the head office at Houston, where he became superintendent of the land and lease department in 1934 and was elected a director of the company in 1941. In these capacities, and also as petroleum engineer for the company, he keeps in intimate touch with all phases of field activity and with the regulation of the industry by State and Federal agencies.

Jan 1, 1943

By Fred W. Menzl, Raymond E. Sutton

GABBS, Nev., in Nye County, is 140 miles southeast of Reno and about 31 miles north of the Southern Pacific railroad at Luning. The townsite lies at the eastern edge of Gabbs Valley, and plant and quarry operations are in the foothills of the Paradise Range at elevations from 5000 to 5900 ft. Hard-surfaced roads connect with main U. S. high- ways on the north and south. Historical Background: Brucite, a magnesium hydroxide mineral, was discovered in the Gabbs area in 1927 and magnesite, the magnesium carbonate, was found later on claims originally staked and worked for the tungsten mineral scheelite. The brucite is on a granodiorite contact and the magnesite is usually some distance away from the granodiorite

Jan 7, 1957

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By P. CHARTERIS A.

THE following scanty notes on the Roumanian oil-region may serve as an introduction to more detailed future study and description. The Roumauian oil-belt, follows the outer edge of the sweep of the Carpathian Mountains, and may, in a broad sense, be regarded as a prolongation of the Galician belt. It is distributed over a tract of country from 300 to 400 miles in length, with a width of from 15 to 20 miles, and is believed to cover an area of at least 20,000 hectares (59,420 acres). The Government claims that 16,000 to 17,000 hectares of its land is petroliferous. The primary deposits of petroleum are considered to be in the Padeogene (Oligocene) and the Neogene (the salines of the Miocene) formations. Most of the other repositories, especially those of Muntenie, are only secondary, the petroleum there having been introduced by the orogeneric movements which raised the Carpathian Mountains. The oil-field has been divided by the Roumanian survey into two regions, the Flysch and the Sub-Carpathian, as is shown in the accompanying sketch-map, Fig. 1.(p. 518). So far as is yet, known, practically all the seepages and .productive pits and wells are situated oil anticlinals. Those which outcrop in the Flysch region. (called Paleogene anticlinals), as indicated in the sketch-map, Fig. 1, are : Solontz, Middle Oligocene; Moineshti, Moineshti and Tagu-Ocna-beds of the Eocene.

Jul 1, 1906

By W. Henry Weimer

A successful surface coal operation requires the combined efforts of engineering and operating personnel. In the planning for a mine, machines should be selected to do the best work in getting the coal uncovered, loaded, and transported to the preparation plant. The best system and extent of cleaning will be determined by the market. After the fundamentals of operation have been established, the operating personnel should see they are carried out. There is no simple solution to some of the every day problems facing the operating officials. Here the production engineer with the technical approach, time studies, control methods, past experience, and available records can help in detecting causes of inefficient phases of the operations. With these studies, a careful analysis can be made in setting up the expected standards to be followed. Management can then compare the job under study with the standards and make corrections to solve the problems. 5.2-1. Annual or Daily Coal Production. Once the production cycle has been established, it is paramount that coal sales keep the productivity of the mine as high as possible. A successful company does this by what they call "the control approach." The daily tonnage report is one of the things that is a potent control tool in attaining the goals to be achieved. If production is falling short of the goal, the daily tonnage report will reveal what has to be done in the remaining days of the month or year to achieve the expected schedule. When goals are reached or exceeded, then budgeted tonnages and costs will be reached or exceeded and thus assure attainment of a profit. Failing to keep to the scheduled pace shows up quickly and prominently, facilitating any necessary action to get things back to the projected plans. The sales target is usually set a little higher than the operating production. The sales tonnage is scheduled and sales are made accordingly, slightly

Jan 1, 1968

By S. F. Emmons

"The obscurity which still veils from us the true nature of veins will become more acid more cleared up when they can be considered in connection with the geological structure of the regions in which they occur." 1 THESE words, according to Lossen, the biographer of the late Dr. A. von Groddeck, of Clausthal, were the last received by him from that eminent man, perhaps the most far-sighted and carefully progressive of recent writers on ore-deposits. They seem to me to form a fitting text for what I am about to say ; since I find that many of the conclusions at which I have arrived by my own study of the structural relations of ore-deposits,or, in other words, of the structural and dynamic geology of the regions in which they occur in this country, have been similarly determined by hint within recent years in Europe, and especially in his home field of work, the Harz. I shall not enter upon a detailed account of how far other workers may have arrived at similar conclusions with myself, since these questions of priority are of little interest, except to those immediately concerned; but will briefly present the methods by which, in my work in this country, I have arrived at certain generalizations, and will point out the practical bearing which they may have upon the work of mining engineers. In my first thorough and systematic examination of an important group of ore-deposits, viz., that of Leadville, Colo., I was enabled, through the generous facilities afforded me by the then Director of the Geological Survey, Clarence King, to

Jan 1, 1913

By R. H. Raring, F. E. Martin

A high speed gas quenching dilatometer useful in studying phase transformations in low alloy steels is described. Changes in specimen length are measured by means of an electrical micrometer tube. The maximum instantaneous cooling rate is approximately 5000°F per sec; the maximum average cooling rate from 1650' to 950°F is approximately 2900°F per sec. Data for steels of 0.11 pct and 0.67 pct C content are included. KNOWLEDGE of phase transformations as they occur in an alloy under conditions of continuous cooling affords valuable insight into its properties. The transformation characteristics during continuous cooling of steels of high hardenability, which decompose entirely to martensite at fairly slow cool-

Jan 1, 1957

By Henry M. Howe

The natural effect of large ingot-size should be to increase segregation. I have previously pointed1 to the excessive segregation in many large ingots as tending to confirm this, but I have shown that in case of ingots less than 16 in. square this expected effect of ingot-size is liable to masked by that of Note.—The "maximum enrichment" of each ingot, i.e., the excess of the richest spot over the average of the whole ingot, is first calculated in percentage of that average. The average of the maximum enrichment of the several ingots of a given group is the abscissa in Fig. 1. The number beside each spot tells the number of cases which that spot represents. FIG. 1.—Influence of Ingot-Size on Maximum EnrichNent in Steel Ingots. other variables. Under these conditions we should expect that, if large ingot-size really does tend to increase segregation, this effect would be shown by taking the average of large numbers of cases, so that the effects of these other variables might off-set and cancel each other.

Jan 1, 1910