Search Documents

By D. L. Creighton, S. A. Hoenig

The field-emission microscope has been adapted for the study of microcrack growth during the early stages of fracture in metal wires. Cracks as small as 6 1 in length can be detected and their growth can be followed to specimen failure. The system is quite useful in searching for microcracks since only sharp-edged surface defects will emit electrons under the experimental conditions. THE conditions leading to brittle fracture were discussed a number of years ago by Griffith1 and the term Griffith Cracks is often used for the small surface cracks which are responsible for brittle fracture. Griffith's theory has been modified by stroh2 and more recent results on metals are discussed by Allen,3 pp. 123-40. At present the phenomenon is not completely understood but there is general agreement that at least in certain materials the sequence leading to brittle fracture involves several stages. The initial microcracks are present because of cooling or working stresses, Hahn et al.,3 p. 95. When a stress is applied to the specimen the cracks grow slowly until the release of stored elastic energy is large enough to accelerate the crack and provide the necessary surface energy for crack growth. At this point the growth rate appears to increase rapidly to some new equilibrium velocity, and failure occurs. Since the microcracks are usually about the size of a single metallic grain (Ref. 3, p. 99) it is not easy to find them and it is very difficult to follow their growth under stress. This paper will report on the use of a cylindrical field-emission microscope for observation of the formation and growth of microcracks. I) THE FIELD-EMISSION MICROSCOPE The field-emission microscope (FEM) has a high magnification and resolution and is almost uniquely suited for observations of microcracks. Since the FEM is relatively new as a metallurgical instrument, a short description will be given here. Normally metals at room temperature do not emit electrons; however in the presence of a strong electric-field gradient, electrons can tunnel out through the reduced potential barrier. Since this tunneling is a function of the local field gradient and the local work function, the emitted electrons can be used to produce a highly magnified image of the surface by allowing them to strike a phosphor screen. Because the electron emission is dependent upon the local field gradient, smooth surfaces emit few electrons except at very high fields. On the other hand cracks, extrusions, or other surface defects, having sharp edges, emit strongly since the field gradient is very high in the vicinity of these defects. This indicates that the FEM should be most useful for detection of microcracks on otherwise smooth surfaces. A field-emission microscope was first used by Muller4 in 1936 for observation of metal surfaces, and recent reviews have been given by Muller5 and Gomer.6 The instrument has been used for metallurgical studies in the area of surface diffusion,= recrystallization,7 and grain growth 8 (Ref. 8 is directed specifically at metallurgists). In the work of Muller4,5 and Gomer 6 the specimen was in the form of a sharp metal point at the center of a phosphor-coated glais sphere. The impact of the emitted electrons on the phosphor produced a highly magnified image of the specimens. Such a system is not practical for applying a controlled stress to the specimen and a cylindrical geometry has been used in this investigation. This allowed the application of a controlled tensile stress to the wire specimen. Normally a cylindrical FEM geometry produces magnification only in the radial direction. This is the case because a smooth wire at the center of a cylinder produces a purely radial electrical field. However, if there is a break in the smooth surface of the inner cylinder, the field near the break becomes three-dimensional and the area of the break is highly magnified. The reason for this is clear if it is recalled that the field gradient depends on the relative radii of the inner and outer cylinders; if a crack forms, its edge radii are of atomic dimensions and a very high field gradient is formed near these crack edges. Since the electrons receive most of their acceleration near the crack edge and are always traveling perpendicular to the field lines, they tend to spread out and produce the magnified image observed in the cylindrical field-emission microscope. 11) BRITTLE-FRACTURE STUDIES A) Experimental Apparatus. The geometrical arrangement chosen was that used earlier by Gifford

Jan 1, 1965

By James E. Howard

AT the request of the Council of the Institute, I have the honor to submit the following remarks upon the Program of Tests under which the current work of the Watertown Arsenal Testing Laboratory is carried on, which comprises, among other items, the tests of steel ingot metal and derivative shapes. The intended scope of the tests may be illustrated by extracts from the descriptive part of the program as submitted by the Laboratory under date of April 17, 1907, and subsequently approved by the Chief of Ordnance, U. S. A. Under Item 1, Ingot Metal-Open hearth, acid and basic; Bessemer, acid and basic; crucible; fluid compressed and uncompressed-descriptive remarks were made as follows ; " A thorough, fundamental inquiry into the physical properties of steel necessarily begins with the ingot metal. Investigations, having for their object the improvement of steels, should also begin with the ingot. A knowledge of the ingot structure is essential for judging of the subsequent behavior or appearance of the metal. Under ordinary conditions, so little information is obtained from the ingot in individual cases that practically none of importance is acquired. These remarks have particular reference to the state of physical and structural soundness of the steel. Questions of chemical composition, segregation, piping and the grosser cavities have frequently been given attention. Defects of continuity of structure, which manifest themselves in the working; of the metal, and at the final stages cause distrust in the finished forging, have generally been neglected. ? The range in physical properties in a given composition of metal, as shown in Tests of Metals, 1902 and 1903, is very great. Tests are there found which, when the results are

Mar 1, 1908

By J. L. Whitlock

An attached growth aerobic biological treatment process has been developed at Homestake Mining Co.'s Lead operation which not only oxidizes free and complexed cyanides, including the stable iron complexed cyanides, but also thiocyanate, and the oxidation byproduct ammonia. Through the employment of a mutant strain of bacteria which has been gradually and specifically acclimated to the waste, these potential pollutants are mineralized to relatively harmless sulfates, carbonates, and nitrates. The resultant effluent, through toxicological testing, has been shown compatible with the receiving stream, which serves as a cold water marginal trout fishery.

Jan 1, 1985

By R. W. Regehr, R. A. Burmeister

Epitaxial growth of GaAs 1-xPx on germanium substrates was achieved using an open tube vapor transport system. The compositional range of 0.3 < x < 0.4 was examined. The best results were obtained with (311) orientation of the germanium substrate. The physical and chemical properties of the resulting layers were investigated using several techniques. Spectrographic analyses of the layers indicate substantial incorporation of germanium into the GaAs t-X Px layer. Evidence is presented which indicates that this incorporation occurs via a vapor phase transport process rather than by solid phase dijfu-sion. Electrical measurements suggest that the germanium thus incorporated behaves predominantly as a deep donor in the compositional range of 0.33 < x * 0.40 and has a deleterious effect upon the luminescent properties of GaAs1-x Px. The increasing technological importance of GaAs1-xPx for use in light-emitting devices has led to an evaluation of several aspects of existing growth processes. The method most commonly used to prepare GaAs1-xPx for electroluminescent device applications is vapor phase epitaxial growth on GaAs substrates.&apos;-4 In a typical electroluminescent diode structure the active region of the diode is entirely within the epitaxial layer and thus the electrical properties of the substrate are relatively unimportant since it is effectively a simple series resistance (assuming hetero-junction effects to be negligible). The use of germanium rather than GaAs as the substrate material is of interest for several reasons. First, GaAs of reasonable structural quality has been epitaxially grown on germanium4-2 and it is reasonable to expect that GaAs1-xPx could subsequently be deposited on the GaAs layer. Second, germanium substrates are readily available with both lower dislocation densities and larger areas than GaAs. Finally, single crystals of germanium are more economical than GaAs single crystals. The principal objective of the present investigation was to test the feasibility of growing GaAs1-xPx epi-taxially on germanium substrates, and to evaluate the properties of such layers with regard to electroluminescent device requirements. The approach used was to a) demonstrate epitaxial growth of GaAs1-xPx on germanium, and b) characterize the relevant structural, electrical, and optical properties of the GaAs1-xPx layers. The possibility of germanium incorporation into the grown layers was of special interest since there was some indication of this in previous studies of GaAs growth on germanium.5&apos;11,12 Although a study of the electrical properties of germanium in GaAs1-xPx was not an intent of this investigation, several features of the electrical properties of the layers grown in the present study which appear to be due to germanium are described. EXPERIMENTAL PROCEDURE The open-tube vapor transport system used for the epitaxial growth of GaAs1-xPx is illustrated in Fig. 1. This system utilizes the GaC1-GaC13 transport reaction and is similar in most respects to the larger system described elsewhere.&apos; The germanium substrates were n-type, with a resistivity of 40 ohm-cm (Eagle-Picher Co.). These were cut to the orientations of {100), {111), and (3111, and were mechanically polished and chemically etched in CP-4 (5 min at 0°C) prior to growth. In some cases, a GaAs substrate was employed in addition to the germanium. The orientation of the latter was {loo}, and they were also mechanically polished and chemically etched prior to growth. The initial composition of the deposited layer was pure GaAs. After approximately 10 microns of GaAs was deposited on the germanium substrate, the phosphorus content of the layer was gradually increased over a distance of approximately 15 microns to the desired concentration and maintained at this value throughout the remainder of the growth. Typical operating parameters used during growth are given in Table I. Selenium was used as a n-type dopant in several runs to facilitate comparison of the electrical properties of the layers grown on germanium with those of layers grown on GaAs substrates, which are usually doped with selenium. The concentration of H2Se in the gas phase was adjusted to a value which would normally yield a carrier density of 1 to 5 x 101 7 at room temperature in layers grown on GaAs substrates. The terminal surfaces of the epitaxial layers were examined by optical microscopy for structural characteristics. Laue back-reflection photographs (Cu radi-ation) were also made on the terminal surface to verify the epitaxial nature of the deposit. After these steps

Jan 1, 1970

By John Birkinbine

In the preparation of the paper upon " The Operation of Warwick Furnace, Pennsylvania, from August 27, 1880, to September 1,1885," presented at the Pittsburgh meeting, I purposely refrained from offering theories to explain the peculiarities of furnace operation, on the ground that it was better for those actively engaged in blast-furnace management to present records of operations, than for one more directly interested in blast-furnace engineering and construction to venture upon the sea of speculation as to causes. The manager of an iron-works naturally feels that he knows as much about his particular furnace or furnaces as any one else, and as Mr. Cook, after his close attention to and study of the Warwick furnace, was at that time unwilling to present theories, I felt a disinclination to assume more acumen than the manager.

Jan 1, 1887

By J. A. Kitchener, J. P. Anfruns

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 µm diam., by single rising bubbles of diam. 0.5 to 1.1mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By I. Milton LeBaron

Operation of the phosphate flotation plant at the Peace valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1947

By I. Milton LeBaron

Operation of the phosphate flotation plant at the Peace valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1947

By J. S. Dodge, I. M. Krieger

The laminarturbulent transition was studied for monodisperse rigid polymer latices as functions of particle diameter and concentration at several tube diameters. Breaks in the graph of friction factor US Reynolds number were used to characterize the transition; rates of shear were sufficiently high so that Newtonian behavior at the high shear limiting viscosity could be assumed. No abnormal behavior was noted at concentrations below 30 volume percent. At higher concentrations, suppression of turbulence was observed with critical Reynolds numbers rising to as high as 5,500 at 50 volume percent. No definite effect on the transition was noted due to variation of particle size or tube diameter. The type of surfactant used to stabilize the latex was found to have an important influence on the critical Reynolds number. INTRODUCTION For some polymer solutions and solid-in-liquid suspensions, the transition from laminar behavior to turbulence in pipeline flow has been reported to take place at unusually low1-5 and in some cases at higher than normal6,7 critical Reynolds numbers. Extreme values of critical Reynolds numbers (NRe*) have been found to range from 1 to 6,000, as opposed to the values of 2,000 to 3,500 which are obtained for ordinary liquids. Observations have also been reported of drag reduction in fully developed turbulent flow, i.e., a decreased value of the friction factor in the Reynolds number-friction factor plot6*10-14 in colloidal and polymeric fluids. In some cases, turbulence suppression (unusually large values of Nre*) was noted to occur preceding the drag reduction,6 while a normal transition was noted in other cases of drag reduction.14 To relate the occurrence of turbulence suppression and drag reduction to the molecular or particulate structure of the fluid, it is desirable to characterize the structural variables with some precision. For most colloidal dispersions and polymeric fluids, this is very difficult; particle sizes, shapes and stiffnesses may vary over wide ranges in the same sample. Recently, however, a colloidal fluid has become available which consists of rigid spherical particles of highly uniform diameter dispersed in a simple Newtonian liquid. These are monodisperse polymer latices, prepared by carefully controlled emulsion polymerization reactions. The purpose of this research was to study the transition to turbulence in these well-characterized colloidal fluids as a function of concentration, particle diameter and tube diameter. Typical flow curves of latices of high solids content are shown in Fig. 1. While these curves were obtained with monodisperse latices, the general shape of the curve is also typical of a polydisperse latex. It is observed that a shear-thinning region occurs for low to moderate rates of shear. At sufficiently high shearing rates a limiting Newtonian viscosity is reached. The viscosity µ diminishes with decreasing volume fraction 4 at all shear rates. For 4 less than 0.25, latices are Newtonian at all rates of shear.15 An increase in average particle size (at a given extends the Newtonian viscosity region to lower rates of shear. A third factor which influences the

By W. W. Harvey, F. O. Dudas

Toward hot hydrochloric acid, the usual order of reactivities of the common copper sulfide and associated minerals is reversed, and the rates of H2S formation vary as [ ]. The iron component of chalcopyrite and bornite reports to the solution as ferrous chloride, while pyrite remains essentially unreacted. If a pressure of H2S is maintained in the reactor, copper solubilization is suppressed, and the primary copper sulfides are converted to finely divided secondary sulfides (principally covellite). The HCl leach reside then consists mainly of covellite, pyrite and acid-insoluble gangue. Copper can be selectively leached from this upgraded concentrate to yield a clean, strong copper sulfate solution for direct electrowinning. Preliminary analysis indicates competitive economics with respect to established hydrometallurgical processes. Other concentrate treatments based on an initial HC1 leach are proposed and relative advantages compared. The common denominator of the major process routes considered is the requirement to regenerate HC1 from an FeC12 solution. Five distinct concentrate compositions were employed in the experimental study, which included some attention to the fates of selected minor constituents of the copper concentrate, especially gold, silver, molybdenum, arsenic and selenium. Significant mineralogical features of reactants and products are described.

Jan 1, 1978

By R. W. Smith, R. W. M. Lai

Although several recent papers have shown that equilibrium contact angle in dodecylamine solution-quartz systems can often be directly correlated with flotation behavior, it appears that under conditions of relatively high amine strength and pH such a correlation can&apos;t be made. Under these conditions, when there are precipitated amine dipoles present, it appears that a dynamic contact angle formed immediately after introduction of fresh gas bubbles into the system is also of importance. The dynamic angle decreases in magnitude as a function of time. Apparently the decrease is the result of changes in interfacial tensions (liquid-gas and solid-gas) as a function of time. Dynamic angles of the type described can&apos;t be observed in trimethyldodecylammonium chloride solution-quartz systems. Several recent papers1-3 have shown quite conclusively that contact angle data can often be correlated directly with flotation behavior in cationic surfactant solution-quartz systems. At the same time, Iwasaki, Cooke, and Colombo4 have shown data for a dodecylammonium chloride solution-goethite system where, in the vicinity of pH 12 and a collector concentration of 10" M, 100% flotation occurs when equilibrium contact angle appears to be zero. A clue to this discrepancy can be found in the work by smith2 who reported the occurrence of dynamic, time dependent, contact angles in a quartz-dodecyl-amine solution system at relatively high pH values and at surfactant concentrations greater than or equal to 10-4 M. It was found that under these conditions, if a fresh bubble was brought into contact with a properly conditioned and polished quartz surface, a large angle was obtained. The large angle, however, instantly started to diminish in magnitude, sometimes to a smaller stable angle and sometimes to its complete disappearance. Also, if the bubble was preconditioned for some minutes (or sometimes even seconds) in the same amine solution, the smaller or sometimes zero stable angle was obtained when the bubble was brought in contact with the quartz surface. One is immediately led to the thought that perhaps it is these dynamic angles when they exist, not stable angles, that are of primary importance in flotation. The present investigation attempts to further study the relationship between contact angle and flotation

Jan 1, 1967

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By C. H. Mathewson, W. R. Hibbard, Robert Maddin

A satisfactory mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.&apos; Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.³ Experimental Procedure Half-inch rods of alpha brass (nominally 70 pet Cu, 30 pet Zn)* were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.4 In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pet nitric acid solution. The back-reflection Laue technique as described by Greninger6 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buer-ger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1949

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A satisfactory mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.&apos; Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.³ Experimental Procedure Half-inch rods of alpha brass (nominally 70 pet Cu, 30 pet Zn)* were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.4 In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pet nitric acid solution. The back-reflection Laue technique as described by Greninger6 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buer-ger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1949

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

By F. Pošepný

Part I.—General Facts and Theories. PAGE 1. Systems of Classification Employed Hitherto, . . 199 2. Standpoint and View of the Present Paper, . . . 206 3. The Xenogenites in General, ...207 4. The Subterranean Water-Oirculation, . . . 212 A. The Vadose Underground Circulation, . . . 213 Filling of Open Spaces Formed by Vadose Circulation, . . 217 B. The Deep Underground Circulation, . 220 Ascending Waters Encountered in Mines, , 222 Related Phenomena near the Surface, . 225 Mineral Springs at the Surface,. . 230 Chemical Constitution of Mineral Waters, . 232 Minute Metallic Admixtures in Mineral Waters, . . . 238 Alterations Produced by Mineral Springs, . 240 Structural Features of the Deposits of Mineral Springs, . . 244 5. Origin of Ore-Deposits in the Deep Region, . . . 247 Manner of Filling of Open Spaces in General, . . . 254 Part II.—Examples or Classes of Deposits. 1. Ore-Deposits in Spaces of Discission, .. 264 General Features and Illustrations, a. Ore-Veins in Stratified Rocks, .. 269 Clausthal, 269; Andreasberg, 270. b. Ore-veins in the Neighborhood of Eruptive Masses, 271 The Erzgebirge, 271; Przibram, 272. c. Ore-Veins Wholly Within Large Eruptive Formations, 274 Hungary, 274; Dacian Gold-field. 275; Verespatak, 276; Vulkoj, 276 ; Comstock lode, 278.

Jan 1, 1894

By Robert E. Campbell

Mining geophysics in 1969 marked a year of growth and consolidation in the application of ground and airborne geophysical methods and techniques with a 20% rise in expenditures for world-wide exploration. Growth was determined by questionnaire survey of industry, geophysical contractors, universities and government agencies conducted by the Society of Exploration Geophysicists. Relative position of metlhods is shown in the accompanying table on page 87. Methods and Techniques Electromagnetic airborne and ground methods showed the largest gains in the utilization of VLF-EM instrumentation. The VLF-EM instrument is a directional radio receiver which is tuned to distant radio transmitters in the 15 to 25 kilohertz band range. It measures vertical real and imaginary components of the magnetic field vector, and is used in geological mapping and surveying for various types of conductors in the ground. Ground VLF-EM instruments, Ronka EM-16 and Radem, are manufactured by Geonics, Ltd., Toronto, Ont., and Crone Geophysics. Ltd., Port Credit. Ont.

Jan 1, 1970

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

It is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4.5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik&apos;s tests will be discussed later Such torsion does not readily yield actual stress and strain values. Therefore a pre- liminary study was made of the effects of repeated direct stresses, that is, tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluniinum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension rest This alloy permitted, therefore rather accurate cont.rol at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this invest~gation appear sufliciently interesting to extend the method of attack in various directions It is intended to study (11 the effects of cycles up to a tew thousands and (2) the effects of strains of different magnitude in tension and compression respectively &apos;The latter variable also includes a. a special case the effects of compressive strains.

Jan 1, 1949

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized. sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country, F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933