Search Documents

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally.' Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan,3 show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision; using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by, the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.5 However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: [3fB = 9.20•'./V•Vn- (n-1) • (n+2) /8[1]] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts' as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of, a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsymmetric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat I than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system, of one degree of freedom can be applied: [1E/m[2] fP = 27] Here f, is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: [t~ = 2/f = 7r\/m/E[3]] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson' 1831) [aP = 4 D2.pL•g•h +7rD•y sin a[4]] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, pL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of-the liquid in cm, y the surface tension in dynes per cm and a the supporting angle' or the one required to insure equilibrium, a being smaller than the contact angle ?. Although demonstrated by Poisson, it has not

Jan 1, 1952

By B. C. Allen

The interface energies of chronzium, molybdenunz. hugsten, and their solid-solution alloys Cv-35Re, MO-33Re, and UJ-25Re were studied at 0.6 to 1.0 of the absolllte liquidus ter)zpe,vature using fiz&apos;e )izethods. Liquid surface tension, yv , was deter mined clsing the pendant-drop and drop-weight methods. Results are, respectizlely, 1700, 2370, and 2480 +100 dynes per ct for the rhernium -containing alloys and essentially the same as tlwse reported for liquid chro)riln, trolybdenum, and tungsten. Average solid slrjace energy, rsv< xias ))zeasured using tlre fiber-extetlsion method. The ratio of ysS, the acerage high-angle grain-boundary energy, to ySV cclas jolnd fronz grain-bolzdary grooue angles fort)zed at the surface in an inert atrfizosphere. Absolllte iute?:face energies were deterawined using ?nultip/rase equilibria involzing suitable liquids of known surface tension (tin, silver). Interpretation of the experimented results in view of pvobable tenzperatzcre, orientation, and purity effects giz,e the follouling approximations in ergs per sq ctn: ysv (i2lo. Mo-33Re) - 2100, ySS (Mo, Mo-33Re) - 800, rr (defornzation twins in MO-33Re at 1200"C) - 800. ysV (Cr. Cr-35Re) - 2400. YSS (CY, Cr-35Re) - 1000. Probably Ylv- YSV- 2500 for tungsten and W-25Re, giving yss (It&apos;, W-25Re) - 900. The interface energies of solid and liqid ch?&apos;omiu?.z, nolybdenu?rr, and tungsten are not geatly aff&apos;ected by rhenium and therefore are not a ttlajor factor in the ductili zing rhenium effect in Croup VI-A metals. THE interface energies of the refractory Group VI-A metals, chromium, molybdenum, and tungsten, are not well-established. The objective of this investigation was to study the liquid surface tension, solid surface energy, and grain-boundary energy of these metals and compare them to those found for the bcc solid-solution alloys, Cr-35e,&apos; 0-33e,&apos; and -25e. Five techniques were used to measure interface energies in high-purity polycrystal rod, wire, and sheet at 0.6 to 1.0 of the absolute liquidus temperature. The alloys were chosen to see if there was any connection between interface-energy behavior and the ductilizing rhenium effecL4j5 EXPERIMENTAL WORK Materials. A description of the materials used is presented in Table I. Chromium rod was prepared by arc melting iodide process crystals supplied by Chromallo Cor., hot extruding, and warm swaging to 0.63-cm-diam rod.6 The sheet was prepared by rolling as-extruded rod to 95 pct reduction in area from a hydrogen furnace at 800" to 900°C and surface grinding off 0.02 cm from each face. Cr-35Re rod was prepared by arc melting sintered rhenium powder and iodide chromium crystals, warm rod rolling to 50 pct reduction in area in cans, and swaging to 60 pct reduction in area at 1100" to 1200°C. Some of the rod was warm-rolled to sheet and then surface-ground. Portions of swaged chromium and Cr-35Re were further reduced by swaging and drawing to 0.013-cm-diam wire by the General Electric Co. Mo-33Re and W-25Re rod, sheet, and wire were provided by Chase Brass and Copper Co. The molybdenum sheet consisted of two lots, both essentially the same except for the carbon content. Liquid Surface Tension. The liquid surface tension of Cr-35Re, Mo-33Re, and W-25Re was measured by a combination of pendant-drop and drop-weight methods using techniques already decribed." Following out-gassing, molten drops were formed on the ends of centerless-ground Mo-33Re and W-25Re rods by electron bombardment at 5 x 106 mm. Similar drops were formed on outgassed Cr-35Re rods by induction heating under 1 atm of 99.995 pct Ar. Solid Surface Energy. Solid surface energy was measured by conducting microcreep experiments on molybdenum, Mo-33Re, chromium, and Cr-35Re wires at 2350°, 2306, 1550°, and 180O°C, respectively. In preparation, gage marks -2.5 cm apart and -0.001 cm deep were circumferentially scribed on the wire with a razor blade. Weights of the wire material were then attached. Five to seven reasonably straight wires were hung in a container made out of the wire material. The free end was placed through a small hole in the removable top and secured by bending a small portion 90 deg. The containers not only tended to provide vapor-solid equilibrium for the wires but also protected them from gaseous impurities. They were nominally 2.5 cm in diam by 5 cm high and were made from extruded chromium rod, Cr-35Re arc casting, molybdenum bar stock, or welded Mo-33Re sheet. After deg re as ing, the assembly was outgassed at a relatively low temperature to 2 x 10"5 mm and then recrystallized 2 to 8 hr at the creep temperature in a rhenium-element resistance furnace. The static argon atmosphere was gettered by tantalum radiation shielding. Specimen temperature was measured optically to 25"C using calibration with known melting points and blackbody conditions. The wires generally developed a stable bamboo-type structure according to Fig, l(b), (c), and (d) and retained their gage marks [upper portion of Fig. l(d)]. One or two of the weights were clipped off to provide a low load for the creep anneal. To minimize the possibility of bending or breakage, the wires remained attached to the top of the annealing container which was held to keep the wires vertical. The distance between gage marks was

Jan 1, 1967

By E. J. McCaustland

The behavior of steel after overstrain and at moderate temperatures is fairly well known. It has been made the subject of much investigation, and our knowledge is clear and definite on many points. The ultimate raising of the elastic limit, after moderate overstrain, and the consequent lowering of the ductility, seem to be well established. It is also well understood that the immediate effect of overstrain is to lower the elastic limit, possibly to zero, but that if not interfered with, this limit will subsequently rise higher than before. The " tests after moderate temperature," reported in this paper, were undertaken to verify the above statements for the particular steel under investigation, and also to determine, if possible, the total time required for complete recovery from this state of overstrain. The behavior of overstrained steel at temperatures at or below 32" F. is not so well known. Tests made by Prof. E. G. Coker, at McGill University,&apos; show that steel, overstrained and subjected to cold, will remain in a state of overstrain for an indefinite period. I am not aware of any other published results of tests along this particular line. The effect of time and temperature on the recovery of steel from overstrain was made in 1902-3 the subject of some investigation in the laboratories of the College of Civil Engineering of Cornell University. A general plan was outlined in connection with the regular courses of instruction in testing of materials; but the press of routine work and the demands of the schedules on the time of the students were so great as to presage long delay in the completion of the work. Not much had been accomplished up to 1904-05, when Messrs. E. C.

Jan 1, 1907

ALASKA Established November 19, 1947 Regular meetings fourth Monday of each month except June, July, and August Theodore A Loftus, Chairman John C Boswell, Vice-Chairman Patrick H O&apos;Neill, Secretary-Treasurer Box 1034, Fairbanks, Alaska District Vice-Chairmen Robert L Thorne, Juneau, Alaska Alfred J Lomen, Jr , Nome, Alaska Donald G. Wilcox, Anchorage, Alaska

Jan 1, 1952

[Executive HERBERT G. MOULTON, Chairman WILLIAM WRAITH, Vice-Chairman ,PAUL D. MERICA W. M. PEIRCE H. Y. WALKER Finance H. T. HAMILTON, Chairman ERLE V. DAVELER HENRY KRUMB Admissions FELIX E. WORMSER, Chairman GEORGE D. BARRON, Vice-Chairman CHESTER A. FULTON PHILIP KRAFT EDWARD MEAGHER Alternates P. B. BUCKY LLOYD C. GIBSON F. T. SISCO]

Jan 1, 1940

By A. S. Yue, A. G. Guy

A study was made of the effects of a prolonged flux of zinc atoms through the a solid solution of zinc in copper. The experimental arrangement consisted essentially of a copper disk about 0.01 in. thick, at one of whose surfaces a gaseous atmosphere containing zinc atoms was maintained, and at the other surface a gaseous atmosphere with a minimum of zinc atoms was maintained. During prolonged theothersurfaceexposure at high temperatures the zinc content of the copper disk gradually built up to the steady-state concentration distribution and then remained at this value. The concentration-distribution curves for various conditions were determined by chemical analyses. The results showed that the condition of steady-state diffusion was achieved. The diffusion coefficients calculated from the experimental data, although not of high precision, agreed with the values obtained by other workers using unsteady-state methods. Relatively slight porosity developed in the specimens in the course of diffusion. A LTHOUGH most diffusion studies have been made under unsteady-state conditions, it is known&apos; that the steady-state method is often superior with respect to the directness and accuracy of interpretation of the data. Steady-state diffusion of gases through metal diaphragms is well known. Also, Harris&apos; and Smith" have used the steady-state method in studying the diffusion of carbon in aus-tenite. The accepted mechanism in this system involves the motion of the interstitial carbon atoms in the rigid framework of the lattice of iron atoms. Thus, there is little difficulty in visualizing the steady flow of the small carbon atoms through the austenite. The situation in substitutional diffusion is quite different. Here the atoms are comparable in size, and it is not evident how a steady flow of one of the atoms through the solid solution might be achieved. At the time the present research was started, it was known that a previous exploratory attempt to produce steady-state diffusion in a substitutional alloy, the Au-Ag system,&apos; had been unsuccessful and had indicated that perhaps there were basic difficulties that could not be ovei-come. Therefore, the present research began as a study of the effect of a prolonged flux of metal atoms through a substitutional solid solution. Eventua.lly, it was possible to produce actual steady-state diffusion in the system chosen for study, the a Cu-Zn alloys. Experimental Procedure The aim in the experiments was to maintain a high zinc content, about 30 pet, at one surface of a copper sheet, and to maintain a low zinc content, near 0 pet, at the opposite surface. The zinc would then diffuse into and through the copper, first building up to the steady-state concentration distribution and then maintaining this distribution. The three types of specimens that were used are shown in Fig. 1. In type A specimens the copper disk through which diffusion occurred was welded to the top of a cylindrical molybdenum tube, the bottom of which also was sealed by welding. At the diffusion temperature the brass chips in the molybdenum container were the source of the zinc vapor which maintained the lower surface of the copper disk at 30 pet Zn. The upper surface was maintained at 0 pet Zn by the vacuum in which type A, and also type B, specimens were diffused. Since the molybdenum container was impervious to zinc vapor, it was intended that the only path of escape for the vapor from the brass chips would be through the thin copper diffusion disk. However, it was found that small leaks often developed at the welded joints during the diffusion treatment, and in most specimens some of the zinc was lost in this manner. Although even small losses of this kind were a serious handicap in attempting to determine the flux through the disk, they did not prevent the maintenance of satisfactory boundary conditions for the attainment of the steady-state condition. Type B specimens differed from type A in having a weight of about 300 g supported on the copper disk by 15 to 20 short quartz rods. This change was made when it was observed that the copper disk was being bowed upward by the difference in the pressures acting on its two surfaces. Since the grain-boundary cracking which occurred in the bowed specimens could be attributed largely to the accompanying creep,3 it was desirable to minimize this effect. The counterweight was effective in significantly decreasing both bowing of the disk and cracking at grain boundaries. Type C specimens differed considerably from the others in that the low-zinc atmosphere at one sur-

Jan 1, 1959

Executive DONALD B. GILLIES, Chairman WILLIAM WRAITH, Vice-Chairman ERLE V. DAVELER PAUL D. MERICA W. H. PEIRCE Finance H. G. MOULTON, Chairman H. T. HAMILTON HENRY KRUMB Admissions CHESTER A. FULTON, Chairman GEORGE D. BARRON, Vice-Chairman A. B. JESSUP PHILIP KRAFT EDWARD MEAGHER Alternates P.B. BUCKY SAMUEL HASKELL F. T. SISCO

Jan 1, 1939

BASIC open-hearth slags have no obviously unique features when compared with slags from other metallurgical operations. Open-hearth slags form and exist at temperatures ranging from 2500 to 3100 F (1370 to 1700 C). In the course of an open-hearth heat, the liquid slag changes slowly and continuously in chemical analysis-the changes reflecting changes in temperature, changes in metal analysis, solution of charged materials, solution of feed additions, and solution of refractories. Throughout the process, the slag performs specific primary functions that are responsible for a large measure of the technical and economic importance of basic open-hearth steelmaking. It is intended in this chapter to present the chemical reactions by which the primary functions of basic open-hearth slags are carried out, to describe the physical and chemical principles governing the extent to which these reactions proceed and can be regulated, and finally to indicate the limitations imposed on other features of the process by the fulfillment of the primary functions. Basic open-hearth slags perform three primary functions. First and foremost, the slag provides a means of removing phosphorus from the liquid metal. The ability to remove phosphorus is largely responsible for the widespread use of the basic open-hearth process. Second, the slag serves as a controlling factor in transferring the oxygen required for the other oxidizing reactions. Third, the slag provides a means of eliminating some sulfur from the open-hearth bath. While the extent of sulfur removal is not comparable to that of phosphorus, the ability to remove some sulfur contributes much to the value of the process. The effectiveness with which the slag fulfills its functions varies with temperature and composition. Since operating temperatures are fixed largely by the specified nature of the product and the equipment, .the speed and extent to which the functions of the slag are carried out depend largely on its composition. The necessity for regulating slag composition to accomplish the re-

Jan 1, 1964

By Paul A. Farrar, Harold Margolin

The Ti-Al-V system has been delineated from 50 to 100 wt pct Ti and front 600 to 1400°C by X-ray and ntetallographic techniques. Isothermal sections were delineated at 600, 700, 800, 900, 1000, 1100, 1200, 1300, and 1400°C. X-ray and metallographic evidence indicated the presence of two phases and in addition to those reported by previous investigators of the ternary system&apos;-3. T HE titanium-rich region of the Ti-Al-V system as originally proposed by Rausch et UZ, and Jordan and Duwez3 was based on the binary Ti-Al diagram as proposed by Bumps et uZ. As additional phases have been shown to exist5-&apos; in the region previously thought to be all a, the titanium-rich region of the Ti-Al-V system is open to serious question. Therefore, in order to determine the effect of the indicated changes in the Binary Ti-Al system on the ternary Ti-Al-V system the present investigation was initiated. EXPERIMENTAL PROCEDURE The experimental procedures in this investigation are the standard techniques used in the study of titanium-alloy systems which have been described in detail previously.1° Consequently, only details pertinent to the present work are discussed. The alloys employed for the delineation of this system were prepared from titanium obtained from the Bureau of Mines (73 BHN) 99.99 pct Al and 99.7 pct V, by the consumable arc-melting technique. The titanium was premelted into buttons of 25 g because spattering during the first melt caused uncontrollable loss of alloying constituents. Typical analyses of the material used have been reported elsewhere Attempts to hot roll the alloys prior to heat treatment were made on the first series of alloys prepared, but as the area of extensive hot workability was fairly restricted, see Table I, this practice was discontinued. The times of isothermal annealing are given in Table 11. A preliminary heat treatment of 96 hr at 1000°C was used prior to heat treatment at lower temperatures. The standard techniques used for polishing specimens involved belt-grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch. In the low-alloy region it was found that the oRo etch, developed by Ence and Margolin,o gave better contrast between phases. Where this procedure did not differentiate between phases clearly, the method of stain etching developed by Ence and was used. It has been previously reported15 that filing of titanium alloys is not desirable for producing X-ray powders, since the powder becomes contaminated by the file material. Therefore, for those samples not brittle enough to Crush, the procedure described below was used. The specimen was wrapped in molybdenum sheet and placed in a vacuum system and evacuated to 0.03 p. Palladium-pur if ied hydrogen was then admitted to the system until a partial pressure of 5o Cm of H was reached. The specimen was heated in the system to the temperature of original heat treatment and was slowly cooled over a period of 3 hr to 400°C while the partial pressure of hydrogen was maintained. The sample was removed from the system after it had completely cooled and was crushed to a powder of 230 to 270 mesh. The powder, wrapped in molybdenum sheet, was dehydrogenated at the temperature of original heat treatment until a partial pressure of 0.03 p was maintained in the system for at least 1/2 hr. The tube containing the powders was quenched in iced brine while still connected to the vacuum system. After dehydrogenation, the powder, except for the

Jan 1, 1962

Executive J V W. REYNDERS, Chairman WILLIAM H. BASSETT E DEGOLYER H C BELLINGER RICHARD PETERS. JR. Finance H. A. GUESS GEORGE OTIS SMITH, Chairman F. JULIUS FONS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A MOSMAN El K MASTERS J. A. SINGMASTIIR Alternates F. G. BREYER C W HAMILTON F. E PIERCE

Jan 1, 1923

By M. E. de Morton

Recovery and early recrystallization of heavily deformed, 99.98 pct Cr was investigated by studying metallographic structure. X-ray line sharpening, electrical resistivity, plastic properties, internal friction, and shear modulus. Appreciable recovery of resistivity, internal friction, and shear modulus together with some hardening and relief of internal strains occurred before the visible growth of a textured substructure above 350°C (recrystallization in situ). The complex behavior of shear modulus, internal friction, and its strain amplitude dependence during annealing are discussed qualitatively in terms of the relative mobility of dislocations. BY plastically deforming fully recrystallized 99.98 pct Cr above the brittle to ductile transition temperature, at -350°C. as in wire drawing, chromium can be made very ductile at room temperature. However, this ductility is lost on annealing at high temperatures when recrystallization takes place.&apos; The present investigation was made to determine the general pattern of the changes in a number of physical and mechanical properties during recovery and recrystallization of heavily deformed chromium as part of an effort to elucidate the reasons for lack of ductility in the fully recrystallized condition. PREPARATION OF MATERIAL Wire specimens 0.027 in. in diam were prepared from arc-melted, electrolytic chromium by extruding, hot swaging and finally wire drawing at 300" to 350°C, i.e. above the brittle-to-ductile transition temperature. The total reduction in area of the wire was 98 pct and the last 3 pct of reduction was made at 100" to 150°C before cooling to room temperature. The impurity content of the material is shown in Table I. Internal friction and modulus measurements were made on a single specimen after annealing in situ at successively higher temperatures. For all other measurements, a fresh specimen was used for each temperature and annealing of these specimens was done in evacuated (0.001 mm Hg) and sealed silica tubes for 1 hr at the various temperatures up to 700°C. EXPERIMENTAL METHODS AND RESULTS The occurrence of a. transition in some physical properties of chromium at - 40°C2 imposed limitations on the temperature region where some of the measurements could be made. The reason for this transition in chromium is at present unknown but is probably associated with an antiferromagnetic state observed below - 40°C.* Heavy deformation produces an anomalous decrease in resistivity when measured at temperatures below -40°C4 though a normal increase is observed above this temperature. On the other hand internal friction in heavily deformed chromium5 over the temperature range 40" to 50°C is invariant with temperature. Above and below this range internal friction is strongly temperature dependent, increasing with increasing temperature. A temperature in this range was therefore convenient for both resistivity and internal friction measurements and for consistency the measurements of the mechanical properties were also made at about this temperature. No structural change has, however, been observed in careful X-ray measurements6 between -195" and 50°C, i.e. departure from cubic symmetry was not greater than 3:10,000; X-ray line sharpening measurements were therefore more conveniently made at room temperature.

Jan 1, 1962

By A. B. Young

T HE smelting industry in Utah is represented by four plants: The Midvale of the United States Smelting, Refining & Mini.ng Co., the Murray of the American Smelting and Refining Co., the Garfield of the same company and the Tooele of the Inter- na.tiona1 Smelting Co. The first two are lead smelters, the Garfield plant is a copper smelter while the last named embraces both a lead and copper smelter. A total daily smelting capacity of over 10,000 tons is represented, of which 4000 tons is lead smelting capacity. With the exception of Tooele, forty miles distant, all of these smelters are within twenty miles of Salt Lake City. Pyrometallurgical operations in this district are con- fined entirely to the production of unrefined bullion, which is shipped east to the various refineries of the respective companies. The smelting industry in this state had its beginning away back in the latter days of the Civil War, many years before the completion of the trans-continental railroad. Ox teams were still bringing their companies of better fixed Mormon emigrants across the plains to the valley of the Great Salt Lake and those in lesser circumstances were still pushing their hand- carts over the same roads to the temporary abode

Jan 1, 1925

[Admissions: B. M. Gottlieb, Chairman Edmond F. Egan K. Marshall Fagin John S. Fuller Edward E. Monteith T. A. Pollard Howard J. Ritts, Jr. Kenneth W. Robbins Harold E. Wright Advertising and Exhibits: Bernard F. Klein, Chairman Bob Diggs Brown R. E. Howard H. M. Krause, Jr. R. G. Parker Mrs. Evelyn R. Robertson]

Jan 1, 1961

With one shaft almost completed and another shaft being sunk, the scope of the Saskatchewan potash area is beginning to come into focus. Some 18 companies have reportedly leased more than four million acres to explore potash possibilities. PCA, farthest along, is located about 15 miles southeast of Saskatoon, and IMC has its project underway near Esterhazy in the eastern edge of the province. U. S. Borax and Chemical Corp. is also reported exploring the area. The field lies in the middle Devonian geological formation which was probed by oil companies along the 200-mile area across the province. Extensive examination began after World War II and deep drilling was started a few years later.

Jan 5, 1958

By M. P. Tixier, A. Poupon, M. E. Loy

Simple qualitative methods are explained for identifying those shaly sands in a well that are most likely to contain oil. A need for more precise measurement of the variables that enter shaly sand analysis is indicated. Field examples are given to illustrate the methods. A theoretical discussion of the quantitative interpretation of shaly sands is given as a basis for discussion and as a guide for the future. While not generally capable of practical application at the present time because of the lack of sufficient accuracy of the electric log data, these methods may become more feasible in the future as the result of the improved logging methods now being introduced. INTRODUCTION Experience has shown that for porous formations containing only a negligible amount of clayey material, reliable information on the fluid saturation and porosity of the reservoir rocks can usually be derived from the electrical logs. The interpretation is based on empirical formulae relating the true resistivity of a porous formation to its lithologic character, to the resistivity of the interstitial water, and to the proportions of water and hydrocarbons in the pores.&apos; If the resistivity of the interstitial water is not known, its approximate value can be derived from the SP curve.2,3 The porosity can usually be determined to a good approximation from a MicroLog, or a MicroLaterolog.4,5 When the reservoir rocks contain an appreciable percentage of clayey material, an additional factor is introduced into the analysis. In a clean formation, the matrix is an electrical insulator, so that the ability of the formation to conduct current is due only to the conductivity of the electrolytes in the pores; in a shaly formation, the shale constitutes a part of the rock matrix able to conduct current, and influences the resistivity of the formation. On the other hand, the spontaneous emf&apos;s and the circulation of the SP currents are also responsive to the presence of the shaly material. All other factors being the same, the deflection of the SP curve opposite a shaly permeable formation is smaller than the deflection which would be observed if the formation were clean. The effects of the presence of shale on the resistivity and on the SP curves in a shaly formation are functions of the amount, of the specific resistivity, and of the geometrical distribution of the shaly material within the formation. The presence of shale therefore constitutes an important complication in electrical log interpretation. It is easy to realize, for example, that the presence of a large amount of clayey material in a sand may have such a predominant effect that the resistivity of the sand will not change very much, whether the pores are entirely filled with connate water, or contain a high saturation of hydrocarbons. Important research projects have been undertaken to investigate the influence of shales and to find a way to allow for this influence in the interpretation of a log. The problem of the SP in shaly sands was analyzed mathematically by H. G. Doll"&apos; for the case of sands with shale laminations. Formulae expressing the resistivity of shaly formations were proposed by Patnode and Wyllie8 and de Witte.9 Other quite interesting theoretical and experimental results have been published by various authors.l0,ll,12,l3,14 The purpose of the present paper is to discuss an approach to electrical log interpretation in shaly sands. This approach is based partly on some of the theoretical and experimental data available in the literature and partly on observations made on actual field logs. Comparatively simple methods for qualitative and semi-quantitative analysis are described. These methods depend principally upon information provided by the electrical logs.

Jan 1, 1955

By O. D. Sherby, J. L. Lytton, C. R. Barrett

Randomly oriented polycryslalline copper of 99.995 pcl was tested in tension at temperatures of 626o, 496o, and 406o. The gvain-size mnge investigated was from 0.03 to 0.7 mm. Grain sizes were produced by two techniques: 1) varying the amount of prior cold work and the amealing time at constant annealing temperature so as to obtain various vecrystallized grain sizes with minimum grain growth, and 4 holding the prior cold work constant while varying the annealing time or temperature so as to obtain varying grain sizes by grain growth. Polycrystalline samples (grain size of 0.03 mm) with a strong. [001](100) texture were also studied. The relationship between the steady-state creep rate, Es, and pain size was found to be the same indepentent of the technique used to prepare the various grain sizes. For specimens with grain diameters above about 0.1 mm ea zuas esse)ztiallj~ independent of grain size, while for smaller grain diameters Cs increased slightly with decreasing grain size. Strongly textured polycrystalline copper, which contained low-angle grain boundaries, exhibited steady-state creep rates that were slightly lower than those observed in randomly oriented copper, of the same gain size. The results are explained by conside?%ng- the contribution of grain boundary shearing to the total strain and the effect of grain size on the resulting creep substructure. EXPERIMENTAL observations concerning the influence of grain size on steady-state creep rates are varied and oftentimes conflicting. Numerous early investigators found that an increase in the grain size resulted in a decrease in the high-temperature steady-state creep rate, i,.&apos;-" Other workers have foundthat ef decreases with increasing grain size up to some optimum grain size and then increases with a further increase in grain size.&apos;- &apos;&apos; It has been suggested that es, decreases with an increase in grain size only because the range of grain sizes studied normally lies to the left of the grain size for optimum creep resistance. However, sherbyl2 and Feltham and his co-worker13, 14 have found that even for small grain sizes 2, does not always decrease with an increase in grain diameter but may be proportional to the square of the grain diameter. A possible explanation for the different creep rate-grain size relationships which have been observed is that in most experimental studies different grain sizes have been prepared by annealing at various temperatures. For metals in which the impurity concentration is high (greater than about 0.1 at. pct) this type of

Jan 1, 1968

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250&apos; to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,&apos; and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944