Search Documents

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

By Thomas C. Wilder

The activities of both components and the partial and integral molar thermodynamic properties of mixing for the liquid Al-Ge system at 1200°K and for the gertnanium-rich Al-Ge liquidus have been determined from data for eighteen alloys of compositions in the range 0.0593 < 0.880 using the reuersible gal-vanic. cell in the temperature interval 9320 to 1258°K. The liqui-dus compositions above 93 2 °K loere also ve determined by observing the discontinuities in the C us T plots for the high-melting alloys. This system shows moderate negative deviation from ideality throughout, the values for y° being 0.212 and 0.189 for aluminum and germanium, respectively, at 1200°K. Pavtial molar Properties of aluminum on the germanium-rich solidus and at infinite dilution in Ge(s) oboue 932°K were estimated from the foregozng measurements and the equlibrium data of previous investzgators. RECENT compilations of data1" have shown an increasing demand for knowledge of the thermodynamic properties of mixing of metallic alloy systems. In the case of binary-liquid systems where one of the components is a semiconductor this information is useful because, primarily, properties of the second (dopant) component on the liquidus, solidus, and at infinite dilution may be determined more accurately than from calculations based on the phase diagram. In this investigation a reversible galvanic cell was used to determine the chemical potential of aluminum in the two-phase region, liquid + [Ge], on the germanium-rich side of the A1-Ge system in the temperature range 932" to 1193°K. In addition, similar measurements for homogeneous liquid A1-Ge alloys for the entire composition range were obtained for the temperature interval 932" to 1258°K. The cell used was: The experimental technique and the treatment of the data were essentially the same as described earlier394 and are elaborated upon only briefly here. Each cell consisted of a liquid aluminum anode and three A1-Ge alloy cathodes of different composition which were held in Morganite alumina crucibles. The alloys were made up from aluminum and germanium weighed to the nearest 0.1 mg to a total weight of 5 to 10 g. Aluminum was a gift of Aluminum Co. of America and had a purity of 99.995+ pct. Germanium of transistor grade was a gift of Bell Telephone Laboratories. The four electrodes were contained in a larger alumina crucible which also held the prepurified fused chloride electrolyte. Contact to the electrodes was made by tantalum wire leads sheathed in alumina. The tantalum leads were centered in the electrodes by suitable positioning of an alumina radiation shield which fitted on the top of the - alulnina crucible. Two chrome l-alumel thermocouples, sheathed in quartz wells, completed the internal cell arrangement. The entire assembly was enclosed in an alumina tube, fitted with a water-cooled copper head so the system could be evacuated and then flushed with purified argon. *

Jan 1, 1967

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962

R. G. BROWN, Bodie, Cal.: Mr. Rickard&apos;s paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard&apos;s divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B&apos; and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A&apos; was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A&apos;

Jan 1, 1897

By B. Chalmers, S. Wojciechowski

THE structure of the equiaxed zone of several A1-Cu samples mechanically stirred during unidirectional solidification was examined. The stirring was produced by rotary oscillation of the mold about its vertical axis.&apos; It was found that in Some samples the structure is not of the same type over the whole of the equiaxed zone; it consists of regions with two different etching responses. Fig. 1 shows this structure in a Al-1 wt pct ku sample. The lighter etching regions with a coarse structure form something like a network and the darker etching regions with a finer structure can be observed as the continuation of the coarse structure inside this network. The difference in size and shape of the dendrite branches (they are rounded in the coarser structure) is similar to that found by Williamson and Chalmers in ice crystals solidified in undercooled water: when the amount of undercooling was small, the ice crystals were more rounded and coarser than these solidified with a larger amount of undercooling.&apos; It seems justified to conclude that the observed structure resulted from solidification under different thermal conditions: the coarser structure solidified first out of the "purer" liquid and with a smaller amount of undercooling and the finer was formed later out of solute-enriched liquid under conditions of much more rapid heat extraction. A considerable change in the heat flow conditions at the later stages of solidification can be easily understood by taking into account that the coarser crystals form a continuous network and the amount of trapped liquid is relatively small; hence the contribution of latent heat is much smaller in the later stages of solidification. The difference in structure and etching characteristic reflects a difference in composition between these two regions. It was found that the darker etching re- gions are harder (30.4 to 31.3 HV5) than the lighter etching ones (25 to 26 HV5). A similar type of structure was found in a A1-4 wt pct Cu sample grown by Czochralski method. Fig. 2 shows the structure in the lower part of a sample grown slowly and then decanted by a rapid removing of the sample from the melt. In a few places trapped liquid solidified in the same manner as in the sample shown in Fig. 1.

Jan 1, 1968

By S. Maemura

Miike Colliery of Mitsui Coal Mining Company, the biggest and oldest coal mine in Japan, is producing a quarter of the national coal production, about 5.2 million tons of clean coal annually and almost a half of which is now being mined under the "slicing Mining System". The slicing system is a mining method to mine a thick coal seam dividing it into two faces, upper and lower. Its history started nearly 20 years ago. However, the all-around modernization of this system has made little progress up to recent years, while mining methods for single longwall faces has made a remarkable progress together with the improvements in mining machineries, self advancing supports and so on. The reason was that the tremendous difference in adaptabilities of mechanized face equipments existing between the upper and lower faces has made it very difficult to increase the total production capacity of slicing system. After our persistent study for seventeen years, we have recently realized successfully the quite satisfactory slicing system, applying the combination of shield type self advancing supports and double ranging drum cutter at both faces. We are now fully convinced of that the high efficient, quite safe and improved slicing system has been basically established for the present. This paper intends to brief the transition on the combination of self advancing supports and mining machines, its results and further to detail the development of shield type self advancing support for upper face and artificial roof material which shall be the key point to be successful in full mechanization of slicing faces.

Jan 1, 1976

By M. J. Mullikin, J. B. Conway

Several different equation forms were studied to determine the extent to which each particular equation type yielded an accurate representation of a given set of first-stage creep data. Specially developed least-squares computer programs were employed to obtain unique solutions for the creep-equation constants. In studies of creep data for lead at 14.5"C, nickel at 70OCC, and arc-cast tungsten at 2400°C consistently good representations were afforded by a third-degvee polynomial in t113. Other effective correlations were obtained with the Andrade, Cottrell-Aytekin, and de Lacombe equations along with a third-degree polynomial in t112. A newly proposed creep equation involving a hyperbolic-sine term in t1&apos;3 was also found to yield very satisfactory results. This appears to be the first use of such a functional relationship in the analysis of transient creep behavior. In general, the deformation behavior of a material subjected to a tensile load is described in a strain-time plot. Experiments have shown that, following the instantaneous elongation which results on loading, the instantaneous slope (i.e., creep rate) of the strain-time curve decreases gradually with time and approaches what appears to be a constant value. Equations, therefore, which are proposed to provide an analytical representation of such first-stage or transient creep behavior must be consistent with these observations. In other words, at time zero, these equations must yield a finite deformation value corresponding to the elongation on loading. Furthermore, the first derivative of these equations must exhibit a fairly high although finite value at time zero, and then values which decrease with time. It is also preferable, in general, that the derivative eventually assume a constant value at high time values. Although many studies of first-stage creep behavior have been made and numerous equation forms have been proposed for expressing this type of deformation behavior, it is still not possible to state with any assurance which functional relationship will be adequate for a given set of measurements. Parabolic relationships have been employed most extensively although logarithmic expressions have been shown to be applicable in some instances. Combined forms1 have been studied in considerable detail and have on occasion been found to be very effective. One such expression is that of iXndradea and involves a modified parabolic expression: where 1 is the instantaneous length, lo is the length immediately following load application, t is the time, and p and k are constants. Another combined form has been proposed by weaver3 as follows: where E is the instantaneous strain, is is the linear creep rate, t is the time, and a and b are constants.

Jan 1, 1967

By E. S. Moore

THE Kolar gold field has been for a long time the most important gold-producing area of India. It is situated in the State of Mysore, southern India, and not far from the City of Bangalore. The productive field is about 3 miles long and in it a gold-bearing quartz vein varying in width from 1 in. to over 10 ft. is worked. The vein carries high values to great depths and many of the mines have paid large dividends. GEOLOGICAL FORMATIONS IN THE MOLAR REGION The rocks of the Molar region are pre-Cambrian in age and bear a close resemblance to some of the pre-Cambrian formations of America. The oldest rocks seen are basic lavas, now mostly altered to hornblende-schists, with which is associated some banded iron-formation; these rocks are similar to the Keewatin schists and iron-formation in the Lake Superior region. The schist is cut by the gold-bearing quartz vein. In certain parts of the area there is also a conglomerate containing pebbles of granite, jasper,, and schist. The matrix resembles a horn-blende-schist and is intruded by small granite dikes, which in some cases have been pinched off by squeezing of the rock. This has led Dr. W. H. Smeeth, Chief Inspector of Mines of Mysore, to whom the writer is greatly indebted for information regarding this area and for his hospi-tality while visiting the field, to regard this conglomerate as a breccia due to crushing of granite dikes in the schist. Dr. J. W. Evans has regarded the conglomerate as probably a squeezed glacial boulder clay. From analogy with pre-Cambrian conglomerates in America, the writer regards it as a metamorphosed rock similar to our basal Huronian conglomerate. However, the main bearing which it has upon the problem under discussion is the apparent fact that it is younger than the schist

Jan 3, 1918

By Howard Eavenson

PRIOR to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and was usually used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia-which was then regarded as the standard coking and gas coal of the coun, try, and the best coal available anywhere for these purposes. With the advent of the by-product oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for cokemaking, gas and other metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than the best of the coal from the Pittsburgh seam, or than any northern coal, and in by-product ovens produce coke that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these seams is shipped in great quantities without beneficiation and is lower in ash and sulfur than the best washed product from any seam mined in the north.

Jan 1, 1932

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette&apos; recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.&apos;."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy&apos;s law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.&apos; Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

GENTLEMEN Herewith are transmitted reports from the Treasurer and of the principal standing committees of the Institute. To these special reports members are referred for details as to the year&apos;s work. Despite the unfavorable business conditions obtaining throughout the year, the Institute was able to carry on its various activities without curtailment and without drawing on the surplus accumulated through previous years. In fact, small additions were made to the Life, Member¬ship and various other funds. It is highly desirable that such additions should continue to be made, especially to the Life Membership fund, for reasons reported last year. At present, money must be used from current receipts in order to enable the Institute to fulfill its obligations to those who on joining the organization commuted their dues by a single payment. In addition, with the passage of years the number increases of those who have paid dues forty years or more and who, by reason of age or dis¬ability, are unable longer to practise their profession. These men have supported the Institute through their active professional life and it would be a pity to lose them as members through resignation or for failure to keep up their dues. In accordance with the By-laws the Board has authority to advance such members, on application, to the Honor Roll of Senior Members and to relieve them from further payment of dues. It has been the policy of the Board to do this liberally, but to keep up this, as well as to meet other obligations, it is necessary for money to be provided. It has been estimated by the Treasurer that nearly $50,000 additional should be placed in the Life Membership fund as soon as possi¬ble to meet these obligations without using current income and to that end it is necessary, not only to avoid running behind currently but to earn, if possible, some surplus each year. The small amount transferred to the Life Membership fund from surplus this year was, as a matter of fact, made possible by certain members paying personally bills that were properly chargeable to the Treasury. Such generosity is common among those active in Institute work and probably no year would have closed with a surplus except for it.

Jan 1, 1923

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200&apos;K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:&apos;4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3&apos;7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By Magnus Troilius

INTRODUCTION BY C. P. SANDBERG. SINCE the discussion On steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results Obtained by different chemists. To any One having the least acquaintance with chemistry., it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application&apos; of chemistry to steel-rail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it Occurred to me, two. years ago, that I could not do better than start a laboratory of my. own, and engage One of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus Obtain without delay thoroughly accurate determinations. Moreover, in Order to carry on the, operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as was found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the&apos; reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

Prof. Frank H. Probert, dean of the College of Mining of the University of California, visited the mining areas in the devastated regions as a member of the Bureau of Mines committee, which is studying the problems presented in the rehabilitation of mines there. He says that the absolute destruction of the coal mines in the Pas de Calais section makes it-necessary to use either the Westphalia or the Saar valley coal. The Saar mines, however, produce a poor quality of coking coal: therefore, it will not be possible to operate blast furnaces very efficiently unless provision is made for the introduction of better coal. He believes

Jan 6, 1919

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts&apos; method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts&apos; method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts&apos; law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts&apos; law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts&apos; law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts&apos; law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969