Search Documents

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

In 1846 a bill was pending in Congress to reduce, or eliminate, the tariff on coal; the debate caused the same writer to visit the mines on the north side of the James River and to write a letter about them to the same paper.' Omitting the political arguments, his account follows: "July 13, 1846. "Early in the morning we rose, washed, combed, and ate a first-rate breakfast, and then went to the Tuckahoe, mined by Messrs. Sneed and Dietrock. Coal was first discovered here sixty years ago, and mined by Colonel Thomas Randolph, the proprietor of the land. They were worked by him for his smith-shops. Since which time they have been worked periodically, up to the war of 1812, when they were abandoned; and recommenced in 1837 under the management of Dr. W. T.- Scott. Subsequently a Company was formed called Tuckahoe Coal Mining Company, which purchased the whole track at a cost of $30,000. They commenced the sinking of a shaft and went as far as 412 feet, and then pitched the fat all into the fire by hauling off altogether in despair. In 1843 Major Sneed went to work at it, and succeeded. I may here remark that Major Sneed has been the pioneer in this business on the North side of the River, and has sunk more shafts than any other man who has pursued this vocation in Eastern Virginia. The difficulties and expense in sinking these shafts are sometimes immense. The coal on the outcrop or surface is not always a guide to where it may be found imbedded many hundred feet under earth and rock. "The Tuckahoe Pits are on the Eastern end of the coal field, within twelve hundred yards of the Canal, and about twelve miles from Richmond. They employ fifty hands and raise some three hundred thousand bushels of coal per year. It is highly bituminous and excellent for the manufacture of iron. The Tredegar and Belle Isle Rolling Mills are supplied with it. It must be good and of the right kind', or they would not use it. These pits are the only. ones on this side troubled-with gas-of course ventillation is necessary. There is not as much water in this Pit as I have found generally in many others, although they have extended their operations to a considerable distance under ground. I have observed in examining the coal mines, that, where they are sunk over four or five hundred feet, they are annoyed by gas, and where there is a less depth they are troubled with water. It is evident, therefore, that water, in the region of these coal fields, does not run through the earth to any extent, even five hundred feet deep, and the farther you go below that the greater the increase of gas. "We next visited William Cottrell's Pits, situated one mile and a half north of this. He employs some thirty hands, and raises from 4 to 500 bushels per day. "T. & R. Crouch's Pits are one hundred yards north of Cottrell's. This firm employ from 80 to 90 hands, and raise from 8 to 900 bushels per day. They are now

Jan 1, 1942

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By R. E. Salvoti

IN underground coal mining, the increasing trend towards mechanical methods is ever apparent. Figures for 1939 showed that 28 per cent of the total bituminous coal production was mined mechanically 1940 statistic will reveal an even higher figure. Factors causing this trend are varied, but the important are the following;

Jan 1, 1941

By Thomas F. McLoughlin, David K. Hylbert

A new method of satellite imagery analysis has been developed during underground mine roof research. Landsat positive film transparencies were projected onto topographic base maps to scale and lineaments enhanced with a Ronchi grating (method A). Thirty-five millimeter slides of video-enhanced scenes were also projected onto base maps (method B). Both methods permit direct plotting of lineaments to scale and direct correlation with surface and subsurface data wing transparent overlays.

Jan 1, 1981

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

As already announced, the Arizona Meeting of the Institute is to be held from the 18th to the 25th of September. There will be a special train from New York City to Arizona and return, to take members and guests of the Institute to the meeting. The Committee in charge consists of Walter Douglas, Chairman, Cleveland E. Dodge, John C. Greenway, Arthur S. Dwight and Julius Kruttschnitt, Jr., and while the plans of this Committee are not complete, it may be announced that the train will be run with the requisite number of Pullman, dining and baggage cars to accommodate those who desire to go, which will accompany the party during the entire week of the Arizona Meeting as per the following program, including, of course, the visit to the Grand Canyon. As soon as details have been worked out, a circular will be issued giv¬ing full information concerning the trip.

Jan 7, 1916

By John B. Hastings

Chief among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr' is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. "The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerons, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the

Jan 1, 1906

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By Francis B. Foley

In examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found a piece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstattian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: Carbon Nickel Chromium Per Cent. Per Cent. PeR Cent. Metal from skin........................... 0.34 1.26 0.63 Widmannstattian zone.................... 0.21 1.18 0.63 Metal from center......................... 0.34 1.32 0.67 Such a condition might result from decarburization followed by recarburization of the skin. This section came from one of the branch runners to the bottom of the mold, not from the main runner, and it is difficult to conceive of decarburization occurring in this portion of a runner. If the metal were stripped while quite hot, some oxidation would take place but the recarburization is unaccounted for. It could not occur by segregation after solidification—the tendency then is for diffusion and homogeneity. The following seems to fit the conditions and is offered as an explanation. The outside layer of normal structure 0.065 in. (1.6 mm.) thick was chilled on the walls of the runner brick when the molten metal first entered the runner. As the molten metal flows by, the outside of the stream

Jan 1, 1920

By Davis Baker

The direct-metal cars or ladles of the Maryland Steel Company have a capacity of 18 tons when filled within 12 inches of the top. On account of this large capacity, the formation of skulls in these ladles is by no means as rapid as in smaller ladles; but a skull once formed is a very unwieldy piece of metal to handle, and especially to remove from the ladle. We have found it cheaper to clean ladles often rather than make very heavy skulls. We aim to keep the ring of chilled metal that forms on the surface of the iron chipped off, so that the skull shall form principally at the bottom until it becomes so thick as to render the ladle unfit for service. Sometimes it happens that a ladle may be held for several hours filled with molten metal. This invariably leaves a large amount of chilled metal in the ladle. Frequently the skull will weigh several tons, and will be of the full size of the ladle inside, with a top crust, having perhaps a hole 12 inches square, through which the molten metal was poured. In order to remove skulls that cannot be easily chipped out with a bar, we use what may be called a skull-extractor, consisting of a hydraulic cylinder mounted in the center of a heavy cast-iron plate, standing vertically on a suitable foundation. Figs. 1 and 2 show the construction and operation of this apparatus, Fig. 1 being a view of the extractor with pistons extended to full stroke, and Fig. 2 a view with ladle in position and pistons about to commence the stroke. in both figures, A is the hydraulic cylinder, B the vertical cast-iron plate, and C the foundation. The water-pressure, admitted through the pipe, P, is 750 pounds per square inch, and the inside diameter of A is 14 inches. There are two pistons: D, fitting the bore of the cylinder, and E, 84 inches in diameter, moving inside of D. Both pistons move together when

Jan 1, 1893

By AIME AIME

MINING geology was granted two sessions, Wednesday morning and afternoon, Feb. 17. The morning session, at which H. Foster Bain presided. first considered Paul M. Tyler's paper, "Economic Notes on Steel-making Alloys." The elements used in these important alloys are chromium, manganese, molybdenum, nickel, phosphorus, silicon, titanium, tungsten and vanadium. Edward Sarnpson and C. K. Leith asked whether chromite concentrates could be used, Mr. Tyler replying that they could if not too high in iron. G. W. Pawel said that they were used at Niagara Falls, nlixecl with coarse ore. In reply to a question asked by A. O. Hayes, Mr. Tyler said that molybdenum had not affected the price of tungsten. After this discussion, E. S. Moore's paper on nickel was considered. H. Foster Bain thought that nickel is well controlled and in good hands, technically and politically. The popular stainless steel in America is the 18:8 Cr-Ni metal. In Germany a Cr-Mn steel has possibilities. It is easy to make, cheaper. has better workability, will stand 85 per cent reduction between heats.

Jan 1, 1932

By A. R. Gregory, A. L. Podio, K. E. Gray

Dynamic elastic properties of dry and water-saturated Green River shale samples were computed from compressional- and shear-wave velocity measurements. P- and 5-wave velocity measurements were made in three mutually perpendicular directions with respect to the bedding planes. Measurements were also made in several different directions by varying the angle between the bedding planes and the direction of propagation of the wave for angles of 0, 30, 45, 60 and 909 The oriented samples were subjected to both confining pressure and axial loads, in excess of the confining stress, in the direction of propagation. In general, P- and S-wave velocities increased with increasing stress levels, with a corresponding increase in Young's modulus. Water saturation caused the P-wave velocity to increase and the S-wave velocity to decrease. Elastic moduli decreased upon saturation, except for Pois son's ratio, which increased, indicating some degree of weakening of the material. The samples showed a moderate degree of anisotropy; this was to be expected from the laminated nature and shallow occurrence of Green River shale. INTRODUCTION This paper presents some results of an experimental determination of the elastic coefficients of anisotropic materials (in particular, finely layered rocks and minerals such as Green River shale) from measurements of dilatational and shear-ultrasonic-wave velocities. Ultrasonic techniques have been used extensively in nondestructive testing. Several methods have been proposed by Mcskimmin, 1 and some of these have been used successfully to measure ultrasonic velocities in rocks. Hughes and Cross, 2 Wyllie et al., 3 and Birch 4,5 developed pulse first-arrival techniques for the measurement of dilatational and shear velocities. Williams and Lamb 6 used the method of cancellation of a traveling wave, which was later modified by Myers et al.' and perfected by McSkimmin. 8 Although this method is highly accurate, it has not been used as widely as the pulse-transmission methods recently reported by Jamieson and Hoskins 9 King,10 and Mattaboni and Schreiber. 11 It has been common practice to use some form of crystal transducers, either quartz or ceramic, that has been cut or polarized in different directions in order to generate either compressional or shear waves. However, accurate determination of shear wave velocities has been difficult due to problems that arise in obtaining a pure shear wave from cross-polarized crystals, which usually also generate a small amount of compressional energy. As reported by Gregory, 12 this energy can be seen as a long precursor preceding the sharp break of the shear first arrival. The need for generating pure shear waves led to interest in mode-conversion techniques, which are based upon conversion of the mode of vibration through wave reflection or refraction at a discontinuity. Arenberg13 showed that for certain materials and for certain angles of incidence it is possible to generate pure shear modes by reflection at a boundary. Jamieson and Hoskins 9 used a pyrex glass-air interface for generating pure shear waves, and King 10 used this method successfully for measuring shear-wave velocities in rocks. Gregory l4 arrived at a similar result by refraction of a wave at an aluminum-oil interface. A plane compressional wave, traveling in the oil phase, is incident on the aluminum at an angle larger than the critical angle for compressional waves, and thereby generates a purely transverse, plane-polarized wave in the aluminum. During the last few years methods have been developed that allow the simultaneous determination of shear and compressional velocities in solids.

Jan 1, 1969

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By Stuart M. Buck, J. H. Bramwell, Edward H. Williams

The Southwest Virginia Improvement Company began operations in the Bluestone Flat-Top coal-field, situated in Tazewell County, Virginia, in the fall of 1881. In May, 1883, the company had built 200 coke-ovens, and by March, 188-1, had 9000 feet of entries, exclusive of air-ways, in the Nelson or Rig coal-bed of this district (which here averages eleven feet in thickness), and had extracted 200,000 tons of coal, representing an area of about twenty acres. About this opening has grown the recently incorporated city of Pocahontas, and the completion of the New River branch of the Norfolk and Western Railroad to this point enabled the company to make large contracts for supplying coal and coke, so that it was deemed necessary, on account of the limited area developed, to work the mine day and night to fill orders. At 1.30 Thursday morning, March 13th, the inhabitants of Pocahontas were awakened by a violent shock, and within a few minutes all knew that the East mine had been the scene of an explosion of so general a nature that, of the 114 men at work, not one had escaped. The daily papers gave more or less distorted accounts of the number of victims, the scenes in and about, the mine, and the probable cause of the disaster. At the request of the company, the President of the American Institute of Mining Engineers appointed the undersigned a committee of three to investigate the matter, and the committee thus constituted presents the following report, accompanied by a copy of the testimony taken daring the investigation, for preservation in the archives of the Institute. Pocahontas was reached on Thursday, April 24th, and left on Friday, May 2d. During this interval the committee made repeated visits to the mine, especially to the points, of most importance, examining it carefully in every part; and summoned a number of witnesses, twenty-six of whom appeared and testified. The mine had been left in the same state as when the bodies were

Jan 1, 1885

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By Edwin Ludlow

I DEEPLY appreciate the honor which has been conferred upon me by my election to the presidency of this Institute, as I feel that it is the highest honor a mining engineer can receive, and I also feel that I am especially fortunate in being called to take the presidency in the year following Mr. Hoover, as I may be enabled in that way to carry on the work which he has initiated. The constructive work that Mr. Hoover has inaugurated has been of inestimable benefit in bringing not only this Institute but the entire engineering profession into a place in the public esteem to a degree which it had never before occupied.. This work Mr. Hoover will now carry on in the broader field of the Federated American Engineering Societies, of which he is president. Through that organization the engineers of this country, in all branches of the profession, will be welded into one compact body reaching from the Atlantic to the Pacific, making the united engineering profession a power for maintaining American . . ideals and standards throughout the land.,

Jan 1, 1921

By Robert B. Coleman

The recent surge in demand for uranium in the US, accompanied by a significant increase in price, has stimulated the search for and development of lower grade ore bodies. At the mill, this translates into much larger throughputs and-compounded by many recently enacted environmental considerations-has made the cost of milling a critical factor in today's uranium production economics. The three conventional milling methods employed in the extraction of uranium ores are reviewed in the following sections.

Jan 10, 1978