Search Documents

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By Stephen G. Wright

Jan 1, 1985

By R. M. Bird

FEW persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co.

Jan 1, 1926

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By B. Bernstrom

A 22-ft diam, 7-ft long, wet autogenous grinding mill was installed in the new Cretaceous plant of the Jones & Laughlin Steel Corp. to prepare crude iron ore for concentration in spirals and flotation cells. The paper describes the flowsheet and gives a description of the operating and metallurgical results that have been obtained. These results include capacity, horsepower, operating problems and a comparison of pilot plant results with those obtained in commercial operation. The Cretaceous plant at the Hill Annex mine of the Jones & Laughlin Steel Corp. was designed with a wet autogenous mill for grinding low grade iron ore so that it could be concentrated by spirals and flotation cells. The plant, on the west end of the Minnesota's Mesabi Range, went into operation in June 1961, and preliminary operating and metallurgical information describing the performance of this mill can now be given. The crude is lean ore from the Cretaceous iron foundation. This formation is a beach deposit of Cretaceous age that overlies the Precambrian direct shipping and concentrating ores. This rock in nature is not extremely hard but is quite resilient, resisting blasting in mining and size reduction in milling. It contains hematite as water-rounded particles and other fragments of the underlying iron formation and adjacent rocks cemented together by a high alumina-silica ferruginous matrix. It is interspersed with hard dense hematite agglomerates and also contains granite pebbles and boulders that were not cleaned off during removal of the surface. It has a 3.48 sp gr and in the stockpile the material consists of frag-

Jan 1, 1962

By Walter E. Hopper

(Wilkes-Barre Meeting, June, 1911.) I. LOCATION AND EXTENT. THE Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five rail-road-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. II. HISTORY AND DEVELOPMENT. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser " Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905, four wells were drilling. Great trouble was experienced with

Apr 1, 1911

By Gerald J. Anderson

The Marquette District of Central Northern Michigan is the oldest of the Lake Superior iron districts with a mining history dating from 1852 up to the present. The total production of all types of ore through 1965 was 338,120, 146 long tons. Emphasis up to the 1950's was on mining the direct shipping ores; however, demands for higher-grade and better-structured ores in the last decade has resulted in a complete shift in emphasis to beneficiating the lowgrade Negaunee Iron-formation to produce high-grade iron ore pellets. The Precambrian sediments of the Marquette Range have been correlated with the Animikie Series of the Thunder Bay District, Ontario, and are contained in a westward plunging synclinorium that is approximately 3 3 miles in length and 3 to 6 miles in width. -The rock unit of major economic importance is the Negaunee Iron-formation that reaches a thickness of 2500 feet near the City of Negaunee. The primary iron content of the Negaunee Iron-formation averages 26 per cent, whereas the altered iron-formation approximates 31 per cent. The Negaunee Iron-formation has been divided into three principal types: diagenetic, oxidized, and metamorphic. The ores produced to date fall into four categories: high-grade soft ores, high-grade hard ores, siliceous ores, and concentrates and agglomerates (pellets). The soft ores generally are found in synclines and in fault-trough structures, bounded by mafic dikes along at least one side, and are mainly found in the basal portion of the Negaunee. In contrast, the hard ores occur in the uppermost portion of the Negaunee and are controlled by structural features such as folds, faults, and dikes. Iron-formation that has undergone diagenetic and metamorphic alteration makes up the main beneficiating ore types. Studies on the Negaunee Iron-formation have played an important role in the formulation of many of the theories on the origin of the Precambrian iron-formations.

Jan 1, 1968

By E. C. Bain

THE more familiar compositions of iron-carbon-chromium1 and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallographic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By Franz Fohr

On July 27, 1919, there passed away a simple, unassuming gentle-man, who, throughout his life, allowed his intense modesty to keep him-self in the background and during his later years effaced himself so thoroughly that but few of his acquaintances knew aught of him. Yet he was one of our accomplished metallurgists, who did good work in the practice of his profession and lived an upright life. Now that he is no longer with us Franz Fohr cannot plead to be overlooked, and those who fondly remember him will be gratified by his receiving his due. Franz Fohr was born, Sept. 7, 1838, in Mannheim, Germany. Of his ancestry, education, and early career we know scarcely anything. We do not even know just when he came to America, or. what led him hither. The first record of his professional work in this country, found among his papers, shows that from July, 1870, to Jan. 1, 1872, he was superin-tendent of the Newark Smelting & Refining Works, then owned by Ed-ward Balbach & Son. At that time the Balbach works at Newark, established in 1850, and the Selby works at San Francisco, established about 1866, were the only important silver-lead refineries in the United States. Mr. Fohr may have been associated with the Balbachs for some time before he became superintendent of their plant or he may have come from Germany but a short time previously. At all events, it is certain that he was at that time an experienced and accomplished metallurgist. After leaving Newark and going to San Francisco, he soon formed a connection with Thomas H. Selby & Co. Early in 1874-this firm sent him to New York to procure information respecting the manufacture of white lead. His engagement in New York terminated on-Jan. 31, 1875. During 1875, Mr Fohr spent some time at Silver Islet and in the Lake Superior copper region, but of his work there no record remains. In the latter part of 1875, or early in 1876, he associated himself as metallur-gist with the Boston Silver Co., operating at Saint John's, Summit County, in which William L. Candler, of Boston, was the moving spirit. That company was developing its mine in 1875. At the end of that year it "had about 800 tons of ore on hand, about three-fourths of which is dress-ing ore, to be concentrated in its very systematic establishment and to be smelted into pig lead." Evidently Mr. Fohr was engaged for the latter purpose. Henry A. Vezin, erudite and painstaking, was the mechanical engineer for the company. In the fall of 1876, Anton Eilers took his family for the first time so far West as Denver and Mr. Fohr went with them. I do not think that Mr. Eilers had any connection with the Boston Silver Co., save possibly in a consulting capacity, but he visited Saint John's and the enduring friendship among Eilers, Fohr, and Vezin, which terminated only with their deaths, dated from that time.

Jan 12, 1919

Jan 1, 1951

Jan 1, 1951

By Arthur F. Colombo, Donald W. Frommer

With the opening of the Tilden mine near Ishpeming, MI, a new era in iron ore beneficiation was begun. A description of a U. S. Bureau of Mines investigation is summarized to illustrate the selective flocculation-deslime-flotation process developed by the Bureau and used at the Tilden concentrator, which is also briefly described. The operating parameters for the selective flocculation-cationic flotation of an oxidized taconite from the Mesabi range are discussed. A water reclamation system using lime and a cationic flocculant was applied to reclaim the effluents from a 900-pound-per-hour flotation pilot plant. About 80 percent of water requirements were recovered, and the calcium content of the reclaimed water was found to be more important than clarity in influencing the selective flocculation and flotation processes. Although reclaimed waters with about 10 ppm calcium registered turbidities of approximately 5,000 ppm SiO2 equivalents, the concentrates produced using these waters contained 64 percent Fe and 55.0 percent SiO2 and had accompanying iron recoveries of 75 percent. Lower grade concentrates resulted from using reclaimed water with higher calcium contents and lower turbidities.

Jan 1, 1976

By J. D. Runkie, A. G. Lyle, G. A. Gillies

Tar evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis GRAPHS In Fig I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas In this instance the four curves are named, respectively the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve In these tests barite was the mineral concentrated, therefore a barite concentrate was produced Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions Percentage Rejection-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows Suppose a concentrate contains 5 per cent of an undesired mineral This indicates

Jan 1, 1942

By C. R. Wohrman

A melt of pure electrolytic iron with about 0.4 per cent. sulfur and 7 per cent. manganese was prepared in connection with a study of inclusions in iron. The alloy darkened rapidly when etched with a 10 per cent, alcoholic solution of nitric acid, and microscopic examination revealed the presence of a semimartensitic, semi-Widmanstättian structure (Figs. 1 and 2) closely resembling the structures found by Benedicks in his artificially prepared "meteoric iron."' The structures found by Benedicks were readily explained by the presence in his alloy of the two well-known iron-nickel solid solutions, taenite and kamacite, and of their eutectoid (?) aggregate, plessite. By analogy, one would infer the existence of similar phases in the iron-manganese alloy just described, such an inference being strengthened by the similarity displayed in many ways by nickel and manganese in their effects on iron. Iron-manganese Alloys are Regarded as Homogeneous Heterogeneity of iron-manganese alloys has not been recognized heretofore, judging from the data of standard metallographic books and those of original papers. In fact, iron and manganese are quite generally regarded as completely miscible in the solid state. Dr. Rosenhain,2 for example, writes: Alloys of group (a), of which those of gold-silver, iron-manganese, and copper-nickel are examples, when allowed to crystallize sufficiently slowly to attain their condition of final equilibrium, present a microstructure exactly similar to that of a pure metal—the homogeneous character of the molten solution is in that case so completely maintained that the microscope cannot detect the presence of any second constituent. Guillet and Portevin3 refer to the iron-manganese system as an example of the "case of metals completely miscible in the solid state."

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By Lawrence K. Nordell

This paper reviews practices used In the selection and sizing of belt conveyors and stacker systems commonly used in crushing and grinding plant facilities. Historical and modern methods of sizing this equipment are presented. The new methods Include: 1) probability theory applications for establishing component reliability, 2) "Monte Carlo" simulation techniques used in evaluating alternative system designs and in establishing service factors and corresponding availability Indices of each system, 3) quantifying the system and component operating characteristics using computer assisted modeling tools simulating rigid body and elasto-mechanic behavior for starting and stopping large and/or complex belt conveyors.

Jan 1, 1982

By Charles A. Chase

This paper, descriptive of a single mine, is presented in the belief that it may furnish useful suggestions to mine-managers encountering similar problems; and it includes the details which will enable them to estimate the value of the methods employed—especially where these depart from common practice. Tt should be added, however, that this mine is not typical of the San Juan district, but differs markedly from neighboring mines in physical conditions and metallurgical requirements. The Liberty Bell mine is situated in San Miguel county, Colo., on the west front of the San Juan mountains, 2 miles north of Telluride. The vein was discovered in 1876 by Wm. L. Cornett, who, with subsequeilt locators, took up claims along the apex. A few hundred feet of development-work was accomplished, and a few? tons of ore were smelted or milled; but profitable working proved impossible under existing

Jan 1, 1912

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain. The policy of leasing mineral deposits was enacted by Congress under the act of March 3, 1807, which provided that "the President of the United States shall be, and is hereby, authorized to lease any lead mine which has been or may hereafter be discovered in the Indiana Territory, for a term not exceeding five years," and in the same year the Government reserved 345,600 acres of land in northern Illinois, valuable for lead. In 1816 Congress provided that in all cases where a tract of public land containing a lead mine or salt spring was applied for by settlers on the public domain, no permission to work the mine or spring would be granted without the approbation of the President of the United States. By the act of March 1, 1847 (9 Stat. 146), the control of mineral lands was transferred, with all records, from the War Department to the Treasury Department, and by the act of March 3, 1849 (9 Stat. 395), supervisory powers over lead and other mines of the United States were transferred to the Secretary of the Interior. Following the discovery of gold in California in 1848, President Polk advocated the leasing of mineral lands acquired from Mexico under the treaty of 1848. However, owing to the lack of communication and transportation facilities and the consequent difficulty of checking on production and operations, leasing was found impracticable. Mining was permitted to be carried on in each district under rules made by the miners themselves and patterned after the Mexican mining system. To meet the situation, Congress enacted mining laws in 1866, 1870, and 1872, which provided for possession by location and for private ownership, after discovery, by patent of essentially all mineral deposits belonging to the United States, except coal. Many other acts were passed by Congress applying to specific regions and states, reserving salt, lead, or other minerals, some of which provided for the leasing of such deposits. However, very few if any leases were issued thereunder. Not until 1901 (31 Stat. 745) were the mining laws extended to include salt, and in 1910 they were revised to specify salines and associated products. At the turn of the century, it became more and more evident that the mining laws developed for metallic minerals were not practical for the development and conservation of oil and gas, coal, potash, phosphate, or oil shale. Following withdrawals by the Secretary of the Interior as authorized by the act of June 25, 1910, the Department of the Interior recommended leasing legislation; however, it was not until February 25, 1920, that the Mineral Leasing Act was passed by Congress. This act authorized leasing all public lands potentially valuable for oil, gas, coal, phosphate, sodium, or oil shale. The Organic Act, creating the Geological Survey in 1879, imposed upon its director the duty of classifying the public lands.' The early years of the Survey were devoted largely to the accumulation of fundamental data and, with only minor exceptions, land classification was not seriously undertaken until 1906. Since that year, it has been actively pursued with respect particularly to leasable minerals and water power values. On March 3, 1873 (17 Stat. 607) Congress authorized the sale of coal lands of limited acreage to individuals at $10 to $20 an acre, depending on the distance from a railroad, and in 1907 a new scale of prices was adopted by the Secretary of the Interior, based, more logically, on the quality and thickness of the coal deposits, their depth below the earth's surface, and their accessibility. At that time it was much cheaper and easier to obtain incidental title to coal rights under the homestead laws at $1.25 an acre. On March 3, 1909, the first separation act (35 Stat. 844) became a law. It authorized patents, with a reservation of the coal and mining rights involved to the United States, to persons who in good faith had entered public lands under the non-mineral land laws prior to withdrawal, classification, claim, or report that such lands were valuable for coal. It solved the problem only partially, and the practice thereupon adopted by the department of making coal withdrawals "from all forms of entry" instead of "from coal entry" expedited the more complete solution effected by later acts. By the act of June 22, 1910 (36.Stat. 583) withdrawn and classified coal lands were declared subject to entry under the homestead, desert land, and Carey acts, provided a waiver of the coal rights accompanied the application, and by the act of April 30, 1912 (37 Stat. 105) the same privilege was extended to State selections and isolated tracts. The act of August 24, 1912 (37 Stat. 496) extended the separation policy to lands withdrawn for oil and gas in Utah, and finally the act of July 17, 1914 (38 Stat. 509) extended it to all nonmineral filings on public lands theretofore or thereafter

Jan 1, 1955

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICHARD, Vice-Chairman D M LIDDELL Secretary, 7 Wall St.. New York. N. Y. C. A. BORN, Treasurer JOHN V. N. DORR LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON. Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 12, 1917

By John D. Siddle

Efficient energy utilization in the electrolytic zinc process, relative to other zinc processes, is one of the reasons for its wide adoption in recent years. Designers and operators of electrolytic zinc plants have pioneered process improvements, new equipment, and operating techniques to conserve energy. As energy costs advance still higher in the future, and competitive pressure against the less efficient producers increases, these or alternative energy-saving methods will be looked upon as a necessity for economic survival. Estimated energy savings which may be achieved by various equipment and techniques are included.

Jan 1, 1977