Search Documents

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for', all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By William L. Fink, Dana W. Smith

In parts I1 and II2 of this series, there were presented results of investigations on the age-hardening of an aluminum-copper and an aluminum-magnesium alloy. It was shown that the simple precipitation theory of hardening3 adequately explained the aging phenomena, including certain so-called "anomalous" behaviors which had caused other investigators to reject or modify the precipitation theory. However, these papers did not discuss the double aging peaks, which have been stressed in recent articles by Dr. M. Cohen4 and Dr. M. L. V. Gayler.6 The present paper is devoted to an explanation of this "anomaly." Fig. 1 is a generalized schematic representation of aging curves at different temperatures. Curve A corresponds to the aging at the lowest temperature, and D at the highest temperature. Certain previous investigators have explained curve A and the initial peaks

Jan 1, 1938

By William L. Fink, Dana W. Smith

In parts I1 and II2 of this series, there were presented results of investigations on the age-hardening of an aluminum-copper and an aluminum-magnesium alloy. It was shown that the simple precipitation theory of hardening3 adequately explained the aging phenomena, including certain so-called "anomalous" behaviors which had caused other investigators to reject or modify the precipitation theory. However, these papers did not discuss the double aging peaks, which have been stressed in recent articles by Dr. M. Cohen4 and Dr. M. L. V. Gayler.6 The present paper is devoted to an explanation of this "anomaly." Fig. 1 is a generalized schematic representation of aging curves at different temperatures. Curve A corresponds to the aging at the lowest temperature, and D at the highest temperature. Certain previous investigators have explained curve A and the initial peaks

Jan 1, 1938

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By AIME AIME

MODERN metallurgy is an art and a science. The art is process metallurgy-extracting metals from their ores, refining them, and alloying them with one another and with certain nonmetals to produce thereby a variety of metallic materials which, owing to a wide range of useful properties, are for many purposes more valuable to man than the individual metals themselves; process metallurgy also includes shaping or otherwise treating metals and alloys to form objects useful to a complex industrial world. The science is physical metallurgy-organized knowledge of the constitution and internal structure of metals and alloys, of the relation of their composition and structure to properties, and of the laws, theories, and hypotheses that purport to explain this relation.

Jan 1, 1942

By G. L. Fisher, R. Maddin

The rate of self-diffusion in silver single crystals during torsional strain was measured over a wide range of tenperatures and strain rates. The torsional strain was applied in a cyclic manner by reversing the divection of twist aftev a certain fraction of the total strain was reached. Surface roughening was substantially reduced in cyclically strained specimens compared with those strained entirely in one direction. Diffusion coefficients were determined using a special sectioning technique whereby slices could be removed parallel to the surface of a strained torsion specimen. The accuracy of the technique was first determined using roughened specinzens statically diffused to various penetration depths. Simultaneous strain-diffusion experiments were then performed over the temperature range 550' to 800 using strain rates of lo-' to 2.2 x 10' sec-'. The increase in silver self-diffusivity during torsional plastic strain was small. In only one case was the enhancement greater than twice the static value of the diffusion coefficzent. The enhancements increased slightly with decreasing tenzperature and increased with increasing strain rate. A dislocation pipe mechanism of enhancement was found to explain the present results satisfactorily. The magnitude of the enhancements and the tenzperatures at which they were observed suggests that a steady-state dislocation density of 10' to 109 dislocations cm-2 existed during the high-tempevature deformation. The diffusion coefficient in an fcc metal can be increased by 1) an excess concentration of point defects and 2) the rapid movement of diffusing atoms along grain boundaries and dislocations. Plastic deformation may be responsible for enhancements by both of these mechanisms. The results of simultaneous strain-diffusion experiments have caused a controversy over the magnitude of the effect of strain upon diffusion. Experiments reporting large enhancements have been criticized for the manner in which the diffusion coefficient was measured. Several of these experiments have been contradicted by other results obtained in a similar manner. No enhancement was reported by two investigators''' who performed their experiments at high temperatures where strain is expected to have little effect upon diffusion. A recent theoretical analysis3 indicates that strain enhancement by a vacancy mechanism will be small and exist only at low temperatures and rapid strain rates. It is doubtful whether any experiment has yet proven that strain enhancements can occur by an excess vacancy mechanism. In the present research, experiments were performed at extremes of temperature and strain rate in an attempt to measure enhancement of diffusion by strain. Self-diffusion of silver during torsional deformation was chosen since two separate investigations4j5 indicate that at least a small enhancement exists under these conditions. An accurate method of determining the diffusion coefficient, mechanical sectioning, was employed after a technique was devised to apply it to the roughened surface of a strained torsion specimen. First, the accuracy of the technique was determined for different penetrations (2fi). Then diffusion experiments were performed at temperatures between 550" and 800°C at strain rates of 10"" to 10"" per sec. I) EXPERIMENTAL PROCEDURE Preparation of Specimens. The experimental procedure detailing the growth of crystals, their treatment, and the annealing techniques during straining are contained in earlier publications.496 The dimensions and orientations of the torsion specimens are shown in Figs. 1 and 2. licatiin of Torsional Strain. The torsion procedure was changed from that used previously. The specimens were strained in cycles to reduce the gross distortion and surface roughening inherent in twisting to high strains in one direction. For all strains above 0.30, the total surface strain was obtained as follows: the specimen was twisted to 0.10 strain in a clockwise direction; the direction was reversed; the backlash in the torsion apparatus was taken up; and the specimen was twisted in a counterclockwise direction through the initial starting point to 0.20 surface shear strain in the opposite direction. The strain reversal took no more than 1 min to accomplish. The total accumulated surface shear strain was arbitrarily taken as the sum of the 0.10 strain in the clockwise direction plus 0.20 in the counterclockwise direction. Although cyclic torsional strain was beneficial, surface roughening and specimen distortion were not entirely eliminated. The variation in the diameter at various points on the specimen was often much greater than the depth of the diffusion zone. Since serious errors might result if specimens were sectioned in the usual manner, a technique of lathe sectioning was devised to allow sections to be taken parallel to planes of equal concentration.

Jan 1, 1967

Jan 1, 1950

Jan 8, 1951

Jan 2, 1953

Jan 3, 1950

Jan 6, 1950

Jan 4, 1953

Jan 10, 1951

Jan 5, 1950

Jan 5, 1953

Jan 11, 1950

Jan 1, 1953

Jan 3, 1951