Search Documents

All previous attempts to cut rock in boring by means of revolving steel cutters have failed, chiefly in consequence of the mis-shapen teeth grinding the rock and themselves simultaneously, until, after a very few revolutions, the points of the cutters were so worn that it was impossible to force them into the strata. The diamond drilling plant being cumbrous, complicated, and costly, and seeing that fully 70 per cent of the boring generally needed is in what is known as the" milder strata," it will be readily understood that much of the work done will not pay a dividend on the outlay, so great is the cost of removal, the wear and tear of the machinery, and the loss of diamonds. The Calyx Drill, however, invented by Mr. F. Harley Davis, has been constructed so as to overcome these difficulties, and will penetrate quickly and .at a low cost this 70 per cent. of the milder strata. The Drill has taken ten years' hard work and thought to bring it to its present state of perfection, and it will now drill with steel cutters the 70 per cent of the work performed by the diamond drills at a greater speed and at about one third the cost of the latter.The utility of the diamond drill for certain work is undeniable, but it cannot by any means be described as a machine of general popular usefulness that is to say, it is quite beyond the reach of the great masses of mankind.

By J. Douglas Causey

In 1984, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied the 13,730-acre Burnt Lodge (MT-065-278) Wilderness Study Area (WSA) in order to evaluate the mineral resources. The WSA is located in Phillips and Valley Counties, MT, about 55 miles south of Malta adjoining the Charles M. Russell National Wildlife Refuge. It is underlain by near horizontal sedimentary beds of the Hell Creek Formation, Fox Hills Sandstone, and Bearpaw Shale. No mines or prospects were found in the WSA. Bentonitic beds were examined, but are generally less than 1 ft thick and, except where exposed, are deeply buried. Kaolin-bearing sandstone in the Colgate Member of the Foxhills Sandstone was sampled and may have potential for use in structural clay products. However, remoteness and inaccessibility of the area make it unlikely that the material could be economically extracted even though some of the material is marginally useful.

Jan 1, 1985

By Alfred Traverse

The Brandon lignite is a small deposit of very low rank coal near the village of Forestdale in the town of Brandon, Vt. It occurs in association with other sediments, principally sands and silts. This lignitic coal has attracted considerable scientific interest since the middle of the 19th century because of the abundance of fossils in the sediment and the rarity of lignite in New England. A cooperative investigation has been developed by E. S. Barghoorn, W. Spackman, and the author in which different phases of the problem have been worked on in a coordinated research program. This paper presents results of an investigation of the very abundant fossil pollen and spores and some other microfossils of the deposit. The studies on which this manuscript is based were made in large part at Harvard University in partial fulfillment of the requirements for a Ph. D. degree.

Jan 1, 1955

Performance of Outotec FloatForce« Flotation Mechanism - A Study in Both Computational Fluid Dynamics and Industrial Scale Measurement

Sep 13, 2010

By Barry A. Hillman

The rapid evolution of computer and field sensor technology is now providing the ability to integrate mine and office operations. Digital maps and mine plans as well as CAD and GIS can be transferred to ruggedized field computers for development of real-time mine surveys and real-time GPS machine navigation and monitoring. Surveyors can insure that their surveys are accurate before returning to the office. Engineers and surveyors are also able to upload field computer-based surveys to mine planning software and directly to mine equipment including shovels, drills, and dozers providing the operator of the equipment with a real-time view of their work space. Production information can be transmitted through dispatch and/or centralized mine servers to update mine plans with mining progress and production data. Static mine models then become a dynamic element of operations, providing greater use of information that emphasizes the spatial aspects of the mine by providing real-time maps, productivity charts, and graphs. This information can be disseminated through various mine communication systems to provide operators and management with real-time feedback as well as daily and weekly reports. Integrated systems now being used in extensive trials are reporting productivity increases of 4 -7% or more thereby providing rapid payback to the mine.

Jan 1, 1998

THE art of mine surveying has made very great progress in recent years, and is still advancing, perhaps faster than any other branch of surveying. The scope of the mine surveyor's duties has greatly increased, his instruments and methods have improved, the responsibility of his position is greater, and the end is not yet in sight.It might be supposed that such a steadily growing subject would have an adequate literature, but this is by no means the case and outsiders commonly judge mine surveyors by their text-books. Hardly any condemnation can be too strong for most of these books. The English books truckle to the antiquated and crude methods apparently still in use in England, and thereby largely aid in perpetuating them; they commonly in illustrative examples give the distances in fathoms, feet, and inches; they spend page after page discoursing on instruments that should have been forgotten long ago; they try to antagonize theory and practice by detailing such calculations as that a certain vein will contain 2,003.907 pounds of galena per square fathom, and then reduce this amazing quantity to hundredweights, quarters, and pounds. Nothing can be more unscientific, or, for that matter, less businesslike, than unwarranted assumptions of accuracy; it is, perhaps, the greatest curse of applied science. Here we have a calculation to thethousandth part of a pound, when there is probably an unavoidable error of two hundred pounds. What shall we say of a man who explains how to measure the depths of shafts to the hundredth part of an inch by means of short brass rods screwed together...

Jan 1, 1909

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors' reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

CONTENTS.IntroductionAcknowledgementsDescription of MineVentilation of MineOrganisation of Fire Fighting SquadsTraining of Fire Fighting SquadsRescue WorkFire Fighting and Rescue EquipmentFire AlarmsConclusionINTRODUCTION.This paper should be read in conjunction with that by R. P. Hooper, entitled &quot;Underground Mine Fire Prevention at the South Mine,&quot; Broken Hill. Contents of the paper have been arranged similarly for easy reference. The methods used in educating employees in the use of Proto apparatus remain basically the same, but many changes in the methods and equipment used in subjugating fires have been brought about by the practical experiences gained by officers of the company in extinguishing the outbreaks which occurred in the latter half of 1944.Three fires took place during this period, the first in July, on M.L. 11 in openings leading to timbered workings previously worked and subsequently abandoned by...

Jan 1, 1946

By Firth B. A

The classification performance of a Dutch State Mines (DSM) Rapped Sieve Bend has been investigated in a series of experiments. Coal slurries of a nominal 0.5 mm size were classified in the separation range of 0.10 to 0.14 mm at pulp densities from 6 to 21 per cent by mass of solids, and flow rates of 110 to 1375 litre min-1.The results obtained showed that the partition curve and water split io oversize was dependent on the solids flow rather than slurry flow rate or pulp density. For most of the operating conditions considered an accurate classification of the fine coal was obtained. The undersize efficiency was susceptible to solids flow rate, and was less than 70 per cent for solids flow rates greater than 16.7 tonne hour-1 metre-1 width of screen.

Jan 1, 1983

By Michel Massé

Eleonore Project- Agenda ? Purpose and Technical Overview ? SmartEXEC Control Capabilities ? SmartEXEC System Archetecture ? SmartEXEC System Advantage Eleonore Project- Purpose and Technical Overview ? Control air quality while maintaining target production levels at minimum energy operating cost ? Improve safety, work place conditions and operation flexibility ? Reduce energy consumption and green house gases footprint

Aug 1, 2013

By Donald H. McLaughlin

PRICES paid for goods and services in paper currencies are undoubtedly determined by many interrelated factors, but among them none is more specific in pushing prices toward higher and higher levels than the vast increase in debts and monetary obligations of our own and practically all major governments. There is nothing unorthodox in the situation in which the gold miners find themselves today. With wages and the prices of all materials required in the production of gold at the high levels characteristic of a period of prosperity, phony or otherwise, and with shortages of both men and machinery to contend with as well, the spread between the returns in paper dollars that must be accepted for gold in the United States and the cost of producing it is rather painfully small for most producers. Technical

Jan 1, 1948

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

By A. G. Mayton

Vehicle vibration exposure has been linked to chronic back pain and low back symptoms among agricultural tractor drivers. The objectives of this study by the National Institute for Occupational Safety and Health (NIOSH) were to assess driver whole body vibration (WBV) exposures and recommend interventions to reduce the risk of back related injuries, particularly relative to vehicle jarring/jolting (the transient mechanical shock components of WBV). The methodology included collecting, from two independent samples, ?eld data and health and work history data of farm equipment operators. Data were collected during mowing, raking, baling, chiseling, tilling, and road travel for different model tractors. Spraying using a sprayer and shrub removal with a skid steer loader were also included. Based on ISO 2631 (1985), the American Conference of Governmental Industrial Hygienists, threshold limit values, presents 0.5 m/s2 as the action level recommended by the Commission of European Communities for overall weighted total RMS acceleration (vector sum for axes x, y, and z) [ACGIH, 2006. Threshold limit values and biological exposure indices. Cincinnati, OH]. WBV measured at the operator/seat interface exceeded this action level. The roughest rides and highest vector sum accelerations occurred with small utility tractor mowers (3.3 and 2.8 m/s2) and a skid steer loader (1.7 m/s2). Major ?ndings from health and work history data showed 96% of participants reported having to bend or twist their necks, although 24% reported neck symptoms. Sixty four percent of participating operators reported experiencing back symptoms (e.g., pain, aching, stiffness, etc.). Recommendations included: specifying a seat that ??better?? isolates operators from jars/jolts with new tractor purchases; maintaining the seat/seat suspension and replacing worn or damaged cushions with NIOSH tested viscoelastic foam padding; using larger diameter tires with radial ply instead of bias ply construction, particularly on small utility tractor mowers, to aid in attenuating ride ??roughness??; using a swivel seat to reduce the stress on the neck from bending or twisting; and improving efforts to educate owner/operators of the adverse effects of WBV exposures. Since the data presented in this paper were collected from two independent samples, the authors were unable to draw any correlations or etiological inferences from the study. However, results were compared and contrasted with other studies which included similar vibration measurements in agriculture.

Jan 1, 2008