Search Documents

By J. E. Hipp

Three electrostatic field sensing proximity warning devices were tested using full-scale cranes and power line systems, a scaled model facility, environmental testing facilities, and theoretical/numerical analysis. The design objective of each device is to assist in safe crane operation near overhead power lines. Several design deficiencies (varying from device to device) were observed, including inadequate overlap in sensitivity ranges, utilization of vacuum tubes and electro-mechanical parts, temperature sensitivity and inaudible alarms. In addition, the testing showed major device limitations including sensitivity to boom orientations and length, polarization dependent responses, and unreliable operation in the presence of multiple power line circuits. The multiple power line circuit problem is intrinsic to electrostatic sensing devices. The remaining deficiencies and limitations are correctable within a state-of-the-art design. This investigation is not intended to evaluate the safety aspects or policy of utilizing proximity warning devices. Rather, the purpose is to determine the performance characteristics of such devices in relation to the criteria specified in proposed MSHA regulation 77.805-4 (i. e., the devices must alarm at a distance of 10 feet from the power line).

Jan 1, 1980

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

Professor Skeats said: I wish at the ,outset to express my appreciation of the h0!-l0ur conferred on me by my election as President of this Institute for the ensuing year. The selection of a geologist for this position by a body of mining engineers andmetallurgists may be taken as an indication of the recognition that the subject is one which may play a useful part in the great metal industry. Among the records of primitive man the finding of implements of bronze and of iron indicated one of the important, advances made in human civilization, and shows that...

Jan 1, 1924

By P. C. Schutte

Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system, and the profession that applies theory, principles, data and methods to design in order to optimize human well-being and overall system performance. Despite the fact that the application of ergonomics principles can make a major contribution to the management of significant occupational safety and health risks, ergonomics is currently applied on a limited scale in the South African mining industry. The objective of this paper is to provide a perspective of ergonomics, the main aim being to create a point of departure for the development of strategic objectives to enhance existing health and safety initiatives through the application of sound ergonomics principles. Two of the major consequences of poor ergonomics, namely work-related musculoskeletal disorders and worker fatigue, and possible means of introducing ergonomics into the South African mining industry, are discussed.

Jan 1, 2005

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

By Y. van der Grijp

The applicability of a stochastic approach to the simulation of gold distribution to assess the uncertainty of the associated mineralization is examined. A practical workflow for similar problems is proposed. Two different techniques are explored in this research: a Direct Sampling multi-point simulation algorithm is used for generating realizations of lithologies hosting the gold mineralization, and sequential Gaussian simulation is applied to generate multiple realizations of gold distributions within the host lithologies. A range of parameters in the Direct Sampling algorithm is investigated to arrive at good reproducibility of the patterns found in the training image. These findings are aimed at assisting in the choice of appropriate parameters when undertaking the simulation step. The resulting realizations are analysed in order to assess the combined uncertainty associated with the lithology and gold mineralization.

Jan 1, 2015

By L Avalos, F Melo Miranda, J Misle, M Ingwersen

"Los Pelambres, majority owned by the Chilean company Antofagasta Minerals, is one of the leading producers of copper and molybdenum in the country. It is located high in Andes Mountains, over 3000 metres above sea level, 316 km from the nation's capital, Santiago.The maintenance service supplied to Los Pelambres over the past 13 years has evolved to the point that FLSmidth now provides an integrated service crucial to the management of their customer's assets. The contract initially involved specialty mechanical, electrical and instrumentation maintenance and has developed to encompass maintenance planning and plant control systems.The integrated partnership has delivered excellent results in the areas of improved availability, reliability and return on investment. The operation is now amongst the industry leaders in plant availability.The integrated maintenance service has delivered: An increase in plant availability from 93%, in the first year, to 96.5% today, generating approximately $50 million additional income per year, Quality work procedures, Process and equipment improvements, Major shutdown planning involving more than 700 personnel, 6000 parts and over 2 000 discrete activities.The ongoing success of the partnership requires a high level of understanding between both companies. A commitment to maintain a long term sustainable relationship, based on a ""win - win"" culture, is the key to this success. In this regard Los Pelambres has been a pioneer in establishing and developing such relationships.This case study will share the lessons learnt, the measures taken to improve performance and the best practices adopted during the 13 year evolution of the maintenance service partnership.CITATION:Misle, J, Melo Miranda, F, Avalos, L and Ingwersen, M, 2013. Integrated maintenance services at the Los Pelambres Mine in Chile - The lessons learnt and best practices developed from a long-term sustainable relationship, in Proceedings MetPlant 2013 , pp 296-331 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By João Paulo Ferreira Santos

Neste trabalho foram obtidos nanocompósitos híbridos constituídos por nanotubos de carbono de paredes múltiplas (MWCNT) e por nanofibras eletrofiadas de nylon 6 em uma matriz epoxídica. Os MWCNT foram funcionalizados com grupamentos carboxílicos e dispersos através de ultrassom na resina epoxídica. A composição resultante foi disposta de maneira alternada com mantas de nanofibras de nylon 6 para formar estruturas compósitas na forma de sanduiches, as quais foram termicamente curadas. Medidas de resistividade elétrica das estruturas obtidas mostraram que uma percolação elétrica entre 0,05% e 0,5% (v/v) de MWCNT foi alcançada. Do ponto de vista mecânico, a incorporação de MWCNT na matriz epoxídica resultou em aumentos de módulo de elasticidade (26%) e na resistência a ruptura (19%), porém, devido a presença de aglomerados de nanocargas, a deformação na ruptura e a resistência ao impacto foram severamente reduzidas para 71% e 33%, respectivamente. Por outro lado, a adição de nanofibras de nylon 6 para formar um híbrido, mostrou-se, bastante promissora ao levar a aumentos de 8% na resistência ao impacto sem ocasionar perdas de módulo elástico, na resistência à ruptura e na deformação na ruptura.

Aug 8, 2018

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By Franciszek Letowski

"Recovery of precious metals associated with a sulphidic matrix has an important economic effect on complex sulphide ore treatment. Because a significant portion of the silver and gold associated with pyrite are rejected to tailings during the selective flotation of pyritic Zn-Pb-Cu ore, other ore processing routes have been investigated.Direct leaching of the ore with ferric sulphate solution followed by separation of different components of the solid suspension by flotation was applied. Such a process allows for: production of zinc sulphate solution; transformation of galena PbS to insoluble lead sulphate PbS04 and its accumulation in a non-floatable fraction together with precipitated geothite FeOOH and other insoluble gangue minerals; separation of sulphur and non-decomposed sulphides in the floatable fraction.Laboratory research carried out on the ore samples from an Alaskan pyritic deposit from the Delta region indicates that gold and silver are mostly concentrated in the floatable fraction.Total recovery of zinc from the ore attains 96.5% to 98.5% after ferric sulphate leaching. About 85% of copper was extracted from the ore during the ferric sulphate and subsequent ferric chloride leaching, and about 6% of the copper remained in the non-floatable fraction and mixed fraction during the leaching-flotation step. Extraction of lead from the nonfloatable fraction during leaching with calcium chloride solution attained 98% to 99%. Extraction of silver from the floatable fraction during leaching with ferric chloride solution reached 98%. Extraction of gold from the floatable fraction during cyanide or thiourea leaching reached 71% to 89%. The results of the laboratory research are presented."

Jan 1, 1987

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

Enhancing the Flotability of Gold-Bearing Ores by a Mixture of Collectors

Sep 13, 2010

In considering the preparation of any paper concerning bearing metals, one feels a certain amount of diffidence in venturing into a field which has been capably explored at great length and in great detail during recent years. Many excellent articles have appeared in technical literature, dealing with the general theory of bearings and of bearing metals, the properties of white metals of the tin-base and lead-base types, and of the recently developed lead-bronzes.The justification for this further excursion into the field lies in the fact that it treats a branch of the bearing metal family which has so far received very little attention, and that of a somewhat sketchy nature, in published papers.The author's object is to give some outline of the history, development, present status and possibilities of the cadmium-base bearing metal alloys, particularly those in which copper is the main alloying element.GENERAL CONSIDERATIONS.It is desirable that attention should first of all be given to the general theory, constitution, and necessary attributes of bearing metals, in order that some of the problems met with during the development work may be better appreciated.Despite some evidence to the contrary, it is fairly generally maintained that an alloy for bearing metal use should be of a heterogeneous nature. It should consist of particles of a hard constituent uniformly distributed through a softer matrix.The basic idea is that the hard constituent should actually bear the load and resist wear, while the matrix imparts the necessary ductility and allows the bearing to align itself on the shaft in service.

Jan 1, 1934