Search Documents

By Shadia J. Ikhmayies

"Nanocrystalline fluorine-doped tin oxide, SnO2:F, thin films were prepared by the spray pyrolysis (SP) technique on glass substrates. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray dispersive spectroscopy EDAX and transmittance measurements. X-ray diffraction patterns revealed the nanocrystalline nature of the films where the grain size was estimated based on the Sherrer formula. SEM micrographs showed that the films are uniform and totally covered with the material and they confirmed the nanocrystalline nature of the films. The absorbance was deduced from the transmittance measurements, and its first derivative was used to estimate the optical bandgap energy. Bandgaps larger than the bandgap of the bulk SnO2iF were obtained, indicating the presence of quantum dots. The hyperbolic band model was used to estimate the radii of the nanocrystallites. A comparison between the results of the different methods was performed.IntroductionTin oxide, SnO2, thin films are n-type semiconducting, transparent materials, which have numerous important applications in optical-electronic device technology. The optical transparency of SnO2, together with its chemical and mechanical stability, makes SnO2 films suitable for many other applications, such as transparent conductive coatings, gas sensors and heteroj unction solar cells [1]. In particular, SnO2 thin films have drawn much interest because of their potential application and integration with microsensor devices. Considerable attention has recently been focused on the development of solid state gas sensors based on thin films with a crystallite size smaller than the Debye length of the material, which show increased gas sensitivity and short response times [2]. In many of these applications, a doped SnO2 film is used as an active layer. Among the various dopants, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [1]."

Jan 1, 2012

By W. G. Davenport

H20 is present in many flash furnace inputs. Examples are: (a) moisture in concentrate and flux (b) humidity in blast (c) moisture in hydrocarbon fuel, particularly coal, Appendix IV. H20 may also leak into the furnace from damaged water-cooling jackets. H2O, especially that it be included H2O, exerts a strong cooling effect on the flash furnace. It is important our calculations. As will be seen from the calculations, gaseous and liquid H2O both increase flash furnace industrial oxygen and oil requirements. This is because gaseous H2O (humidity in blast) must be heated from its input temperature to the flash furnace off gas temperature. Liquid H2O must be evaporated and heated.

Jan 1, 2001

By John J. Friel

Digital imaging systems are particularly useful in microscopy, because they make it possible to extract information not readily accessible by manual methods and to display that information clearly. Computer-aided imaging systems analyze, process and compare images, and of these, image analysis is most useful in materials science. Image analysis quantifies the microstructure by making measurements on the entire field or by measuring the size and shape of features individually. Even true surface area can be calculated. Modem image analyzers make thousands of measurements in seconds, leaving the investigator to interpret the data and relate them to process and material properties. Image processing, which may be necessary to prepare an image for analysis, includes everything from simple contrast transforms and kernel filters to complicated processes such as grain boundary reconstruction using artificial intelligence. An example of image comparison is point-by-point screening of X-ray maps of different elements to extract phases. In all of these operations, the computer makes a large number of measurements in seconds and returns information that could not be realistically obtained by manual methods.

Jan 1, 1992

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By William Gregg

Recent environmental and workplace safety legislation has Imposed more stringent limits on the amount and type of particulate emitted Into the air. In the past, the mass of particles contained In a volume of air was the governing criteria. Now the size and precise chemical nature of the particulate must be known and controlled In addition to it's ?mass. Processors of metallic materials have to implement stricter control practices and more efficient control equipment to meet the new regulations. Pulse-Jet dust collector systems are being used to control particulate emissions from various process gas streams. Pulse-jets :are also being used for maintaining a healthy environment In the workplace. this paper will discuss the impact of these regulations, the control techniques used to comply with such regulations, and the equipment needed for compliance.

Jan 1, 1992

By Juan B. Cabezas

"The favorable characteristics and workability of plastics as a replacement of wood, lead, stainless steel, asphalt and other materials are described. Various types of plastic have proven to be the most favorable choice for handling a variety of acidic, alkaline and organic solutions, as well as pulps, chemical wastes, slurries or tailings for impoundments. The material origin of various plastics, methods of manufacturing and specifications applied to leaching solutions are discussed, including availability and costs. Examples of select plastics are considered for use as alternatives of other materials under severe environmental requirements.IntroductionHydrometallurgical processes applied to gold recovery, as well as other metals, require the use of strong solutions of alkaline, acidic or organic nature, and may also include a variety of materials with extraneous characteristics and complications for handling in storage.The technology of leaching has been in use for more than 100 years, but the applications of leaching processes in metallurgy have become more commonly used in the last 15 years. Suitable materials for the construction of containers, launders, piping, and various accessories, to be used in the handling of leach solutions or slurries, have become a serious problem. Various metals such as brass, lead, stainless steel, etc., and non metallics including wood, clays, glass, rubber, ooncrete, tars or miscellaneous compounds have been tried in the past with serious limitations in workability and resistance to wear and corrosion. For example, the use of metallic, wooden or glass piping systems would require extraordinary shop maintenance to keep such systems in operation"

Jan 1, 1997

By M. A. S. Siraa

A program of work was undertaken at the Kennecott Smelter and Refinery to model the complex. This effort contributed a total of eight models of the plant: flash smelting furnace, flash converting furnace, slag concentrator, anode furnace, offgas scrubbing system, acid plant, hydrometallurgical dust treatment plant, and the precious metals plant. Some of these models have been used in a variety of investigations ranging from offgas capacities for a steam generation analysis to an examination of impurities. The culmination of this enterprise has resulted in an on-line control scheme for the flash smelting and flash converting furnaces. These two process control schemes incorporate their respective steady-state heat and mass balances that are executed in response to feed changes while a feedback loop calculates when product grade and temperatures deviate from setpoints. This system has been put into place to improve furnace control and on- line time.

Jan 1, 1999

By P. V. Ananthapadmanabhan

Feedstock powders of metals, alloys and ceramics for thermal spray applications have to meet several specifications. Particle shape, size and distribution, powder flow characteristics and density are the important factors that need to be controlled, in order to ensure high spray efficiency and better coating properties. Thermal plasma technology can be effectively utilized to produce metal, alloy and ceramic powders for spray applications. The present paper describes plasma spheroidisation of commercially available aluminium powder and nickel-aluminium powder blend in a plasma reactor. Results show that the processed powder particles bear spherical morphology with excellent flow characteristics, which make them ideal for thermal spray applications.

Jan 1, 1997

By Carla Lupi, Mauro Pasquali

"Photographic technology is based on light sensitivity of silver halides that, because of silver properties, are capable of forming photographic images. Photographic laboratories and hospital departments because of digital photographic systems less use this technology today. Nevertheless recovery of silver is still advantageous because environmental problems related to Ag ions danger to biological system. Many processes have been studied to treat silver containing photographic bath: cementation, chemical precipitation and electrowinning. In this work, after preliminary voltammetric tests, a batch electrometallurgical process has been studied to completely deplete the silver containing photographic fixing baths. The effect, of silver concentration in the electrolyte, varying over the range 0,2-1 g/L, bath stirring and current density ranging from 10 to 500 A/m2 on process yield and deposit quality, has been investigated. Introduction Photographic wastes, electronic scrap and spent catalysts constitute the main sources of materials for silver recycling. Among those silver secondary sources, the photographic discharged material could be still important and useful, even if photographic laboratories and hospital departments, because of digital photographic systems, less use photographic technology. Several processes have been developped in order to recover silver used in the field of photography from both photographic solutions and scrap film paper[1-5]. Fixing solutions are very complex baths but, because of silver position in the electromotive series, electrolysis could represent an advantageous method for silver recovery. Electrolysis produces high purity silver without generating new pollutants, while the fixer can be reused: obviously it is necessary to purge off a portion of this solution in order to avoid the excessive build up of other deleterious compounds into solution. A tested recovery method was constituted by the dissolution of silver from X-ray films with concentrated nitric acid. Internal electrolysis and external electrolysis methods were carried out using a steel electrode as cathode and a copper electrode as anode [6]. Silver recovery from photographic chemical solutions has been also performed in a special cell [7]: the solution is supplied to the bottom of a non-agitated cell having a vertically elongated form and including a central anode enclosed by a cathode. An other study discloses the use of an electrolytic cell comprising at least one anodic compartment and one cathodic compartment: the solution is treated in the cathodic compartment and then recycled in the anodic one [8]. A more recent work proposes the use of zirconium cathode for the recovery of silver from photographic fixing solution [9]: studies carried out by cyclic voltammetry showed that about 98% of total Ag can be recovered with an electrical efficiency close to 92%."

Jan 1, 2008

By Abhishek Asthana

The incineration of Municipal Solid Wastes (MSW) is an attractive process for reducing the volume of the wastes and recovering their energetic value, which, however, requires to be strictly controlled in order to limit its impact on the environment. In this context, we have undertaken the mathematical modeling of the different sections of a typical incineration plant. The combustion of the waste bed, usually carried out on a moving grate, is at the core of the process. This paper presents the 2-dimensional, steady-state model that we have developed for simulating the MSW combustion. The model describes gas flow through the porous waste particle bed, the gas-solid reactions, conductive and radiative heat transfers, drying of the feed, its pyrolysis and the emission of volatile species, combustion of the pyrolysis gases, the formation of char and its gasification by water vapor and carbon dioxide, and the consequent reduction of the bed volume. Pyrolysis kinetics distinguish between cellulosic and non-cellulosic materials and are experimentally derived from our laboratory measurements. The calculated results give a deep insight into the various involved phenomena, an example being the complete consumption of oxygen in a large zone of the bed and the related appearance of a char gasification zone. The influence of various operating parameters, like the temperature and flow rate of primary air, is presented and explained. Finally, the effect of stirring the waste bed on the moving grate is also analyzed.

Jan 1, 2006

By F. W. Warnaars

Chanarcillo is a historically well-known silver deposit which produced over 100 million ounces. High grade vein-type mineralization is confined to a prominent set of nearly vertical, NNW to NE fractures that intersected limestones, andesites and tuffs of Early Cretaceous age. A significant amount of disseminated silver mineralization extends laterally outward from the fractures for considerable distances in pyritic carbonaceous limestones, whereas more competent volcanic beds rarely contain lateral mineralization. Local exposures of skarns are mostly barren. Silver and minor base metal mineralization was probably formed peripheral to a granodioritic intrusion inferred to exist at shallow depth. Part of this intrusion is exposed nearby where it contains significant hydrothermal mineralization and alteration. This intrusion was dated at 83.8 m.y.

Jan 1, 1987

By René Bustamante

A GPSS/H simulation is beeing done for a traditional smelter of copper, which envolves a reberberatory furnace, a set of Peirce Smith converters (PSC) and a refining furnace. The objective is to try different plant layouts, being the handling of liquid material at high temperature one the mainly concern, this envolves a study of the ladles and cranes used. Some of the modifications that can be evaluated through the model is the role of oxygen potential when tonnage oxygen is used, number of cranes, PSCs in operation, etc.

Jan 1, 1992

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By A. A. Shook

The off gas from the #5 converter at BHP Copper's San Manuel smelter was analyzed continuously over a period of several weeks using an online sulfur dioxide analyzer. These data have shown that the oxygen utilization efficiency of this copper converter was somewhat lower than anticipated, and that oxygen efficiency declines significantly during the copper blow. A sharp reduction in sulfur dioxide generation was consistently observed at the end of the copper blow, which could be used by converter operators to prevent over-blowing and minimize rolling out of stack.

Jan 1, 1999

By J. Tang

The major problem with the Nd-Fe-B magnet is its low operating temperature, i.e., the coercivity decreases so rapidly with increasing temperature that the practical maximum operating temperature-is only 100 °C. Meanwhile, it has been reported that nitrogen addition can drastically increase the Curie temperature of both R2Fe17 and RTiFe11 (R = rare earths). A reasonable question is, then, can one see a similar effect in Nd-Fe-B system? Experiments have been conducted to examine how magnetic properties of Nd-Fe-B magnet are affected by the nitrogen addition. Our results show that part of Nd2Fe14B maintains its original crystal structure and no substantial change in To, due to such N2 treatment is found. However, part of the sample decomposes into a-Fe and, possibly, Nd nitride as a result of nitrogen treatment.

Jan 1, 1992

By D. J. Cassidy

This document discusses commercial strategies and applications of specialty processing plants for the recycling of nickel, copper, zinc and cobalt bearing by-products. For this discussion, I will focus on materials originating from the metal plating, electronic circuit board· and chemical industries. The review of select processes and the required service, sourcing, material handling, processing and marketing strategies necessary for a successful recycling program are highlighted. Materials discussed in this summary include filtercakes, filters, dusts, spent catalysts, spent solutions and solids. Both pyrometallurgical and hyrometallurgical applications to these materials are addressed. A comparison of targeted finished markets, including smelter feeds and value added products are also reviewed.

Jan 1, 2000

By Guray Kaya

Boron minerals are widely employed in various fields such as ceramic, glass, cement, metallurgy, etc. Although boron deposits of the world are limited, the production level of boron-based products is continuously increased. Turkiye possesses approximately 73 % of total world boron resources. Etibor Kirka Borax Company of Turkiye produces tincal concentrates and borax pentahydrates. During such productions considerable amounts of concentration and derivation wastes appear. Having considered the increased rate of production it is quite obvious that the level of relevant wastes will also be raised. With this study it was aimed to utilize these wastes in roof tile and brick bodies and to convert them into a form environmentally and human friendly. Newly produced products were undergone to several standard tests for the determination of their shrinkage, water absorption, strength values and coloring parameters. Additionally, micro structural studies were conducted.

Jan 1, 2006