Search Documents

By S. P. Marsh, D. Banerjee

"Casting processes involve phenomena that occur on widely disparate length-scales. Simulation of macroscopic effects, such as heat transfer and convection, are generally addressed by solving the appropriate equations in discretized form on a finite-element mesh. Microscopic phenomena are described by micromodels that may be empirical or analytical in form. Coupling of phenomena in these two regimes is a critical issue in predicting microstructure and defect formation resulting from macroscopic process conditions. A formalism has been developed for expressing micromodels in a consistent manner using stereological parameters to quantify the geometric characteristics of the developing microstructure. This approach provides a robust and physically consistent method for coupling local micromodels with the macroscopic fields. The macroscopic state variables at each node serve as global constraints on the micromodels that are applied to a local unit volume. An outline of an equiaxed solidification model based on this approach is presented, along with preliminary simulation results. Coupling of convection and enthalpy effects between the micro and macro regimes is also discussed. IntroductionThe primary goal of casting simulations is to improve the reliability of cast parts while minimizing cost and development time. Effective simulations can speed up the mold design process and reduce the likelihood of defective parts by refining a particular casting process on a computer, reducing the dependence on cost- and time-intensive prototype castings. The challenge in developing effective simulations stems from the need to address physical processes that occur over a wide range of length-scales, from microscopic (atomic) and mesoscopic (microstructural) scales to macroscopic distances comparable to the size of the casting itself. Overviews of the various thermophysical phenomena and computational factors that are important in solidification modeling are provided in the literature by Rappaz [1] and Tseng et al. [2].Macroscopically, the solidification process is largely governed by the rate of heat flow from the alloy through the mold wall. Another important effect that occurs on the scale of the casting size is convective flow of the melt, which is driven by density-variations in the melt. Macroscopic calculations employ finite-element or finite-difference methods to solve the sets of equations that govern these effects, and the spatial resolution is determined by the grid spacings used for the calculations. Typical spatial resolutions are on the order of 10-2 to 10-3"" meters. This represents a compromise between the resolution required to simulate the continuum transport processes accurately, and the computational time required to model the entire solidification and cooling process."

Jan 1, 1994

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By Fuming Wang, Lifu Hu, Changrong Li, Ruipeng Pang

The solidification structure of 430 ferritic stainless steel has been calculated in the solidification process by using 3D-CAFE model under the condition of water cooling. The calculated results consistent with those obtained from experiment. Under watercooling condition, the solidification structure consists of chilled layer, columnar grain zone, transition zone and equiaxed grain zone

Jan 1, 2015

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By James A. Sommers

Hydrolysis of NbC15 is used to recover oxide values for ceramic and metals production. Reaction of NbC15 with water is rapid, exothermic and vigorous, yielding a gelatinous slurry. In contrast, dissolution of NbC15 in 12 N HCl is endothermic, resulting in a clear yellow solution. Such solutions can be de-hydrochlorinated by controlled contact with air, to precipitate a tantalum¬rich solids, depleting the liquid of its tantalum content. In this way, cheap, useful Nb-Ta partial separation is achieved. The separation is based upon differential oxide-chloride stability. Nb2O5 with <200 ppm Ta/Nb has obtained from starting levels of 2000 ppm. Observations are made on the different types of hydrolysis.

Jan 1, 1992

By Marcela C. Santini, Luiz A. Teixeira

"Surface conditioning (also referred as etching) of plastics prior to metallization is generally conducted with sulfuric I chromic acid solutions. Although these baths perform well technically, the presence of Cr (VI) imposes serious operating problems of an environmental nature. The present work reports ·the results of a study of surface conditioning o(ABS using solutions based. on sulfuric acid, with hydrogen peroxide and/or nitric acid, replacing chromic acid, as oxidants. Process performance was evaluated by SEM and by the uniformity and adherence of electroless nickel coatings applied on selected conditioned samples. The results showed that the evaluated types of solutions could be optimized to perform as well as the chromic-based baths, with a much superior environmental quality.IntroductionMetallization of plastics is normally undertaken for either decorative or functional purposes. Through metallization, the specific properties of plastics such as light weight, design flexibility, and low-cost of manufacturing are enhanced by the addition of properties usually associated with metals. These include reflectiveness, abrasion resistance, electrical conductivity, and a variety of decorative effects (1).The available processes that can be used for metallization of plastics are vacuum metallization or vapoµr deposition; indirect metallization and plating (1). Plating can be sub-divided into electroless plating and electroplating. In electroless plating, metal ions in aqueous solution are deposited on the .activated plastic surface by oxi-reduction reactions without the aid of an external electric potential, forming a thin metallic layer. This electroless deposited film has two functions: (a) it provides an electrically conductive substrate that allows further coating by electroplating; and (b) provides a secure bond between the plastic substrate and the electroplated layer (1,2). In case the electroless metallic part requires an additional layer for finishing purposes, or just an increase in thickness, the part can be additionally electroplated with a· variety of metals - in most cases those are copper, nickel or chromium (3)."

Jan 1, 2000

By Peter M. DiGiacomo

In situ leaching technology requires information about how injected fluids flow in the rock in relation to the localization of the valuable minerals to be leached. In oxidative leaching of sulfide copper ores, flow channels can be determined by the observation of residual iron oxides. In contrast oxide copper ores do not leave a detectable residue after leaching. Method is developed that allows a selective labeling of the leach residue with fluorescent compounds. The fluorescent zones can be detected in corings after the leaching operation.

Jan 1, 1981

By Dengfu Chen, Yunwei Huang, Mujun Long, Kui Lv, Pei Xu, Lin Bai

The surface temperature of continuous casting slab in the secondary cooling zone is a key parameter of production control. However, the accuracy of radiation temperature measurement of high temperature casting slab is greatly affected by the environmental factors, such as water vapor, spray, water film and other participational medias during continuous casting process. In this paper, the radiation characteristics of water vapor and its influences to radiation temperature measurement of continuous casting slab were investigated. Based on the database HITRAN 2004 and the measuring principle of monochrome thermometer & colorimetric thermometer, the measuring errors under different operating infrared spectral wavelength were compared. Results showed that spectral region with wavelength nearby 1.0μm or 1.6μm would be the optimum for high temperature infrared thermometer used under the conditions with moist steam, water spray and water film at the secondary cooling zone in steel continuous casting.

Jan 1, 2016

By Xi-Shan Li, Qian Li, Yong-bin Yang, Tao Jiang, Jie Ge

Compared with other pretreatments of sulfur & arsenic-bearing gold, double-layered pellet roasting has an advantage that sulfur dioxide and arsenic trioxide volatilizing from this refractory gold ores can be solidified into the coating without emission during the roasting. However, the separation of coating from roasted double-layered pellet should be focused on in the novel pretreatment. Based on the difference of physicochemical characteristics between roasted solidified coating and pellet core, several separation methods including grinding, drop impact and water quenching method had been systematically studied in this paper. The results showed that magnetic and gravity concentration could not obtain a satisfactory separation effect. The optimum separation rate of grinding was only 38.94% at grind time 12min, but it increased to 85.05% by drop impact under drop height 0.75m, drop times 20 and impact angle 45°, and that of water quenching taking advantage of slaking reaction of lime could approach 75.32%.

Jan 1, 2015

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By Xiaohui Li, Lianyun Liu, Hongmin Zhu, Chunfang Zi, Kai Huang, Hongjie Li

"The dissolution kinetics of steelmaking slag in pure water was studied, and the relative influential factors were investigated. The dissolution behavior of slag particles in water was well described by Noyes–Whitney equation, and for this kind of sparingly soluble rigid mineral this simple model was extensively applicable to describe their dissolution process. Experimental data were also obtained to confirm the significant promotion effect on the growth of some algae.1 . IntroductionIt has been found that the population of phytoplankton distributed in the ocean was significantly related to the concentration of some elements [1]. For example, silicon and iron were very low in the high-nitrate low-chlorophyll (HNLC) areas, which was the main factor limiting phytoplankton and other biomass growth in these open ocean surface water [7]. The silicon and iron-rich test also confirmed that the supply of these elements had the direct effect on the growth of phytoplankton processes at HNLC areas [2-8]. So in order to promote the growth of phytoplankton in these ocean areas, providing some of these elements into these ocean areas is a natural idea for choice. Steelmaking slag is a good resource for consideration because it usually contains silicon, iron, phosphorus and other elements that are necessary for the growth of phytoplankton [8-10].Haraguchi has proposed the following idea that [5-6], if steelmaking slag can be spread to the open ocean, the trace components like silicate, iron and phosphate as the indispensable nutrients for the growth of phytoplankton, will be leached into the sea water, not only promoting the growth of phytoplankton, but also making good use of these huge amount of steelmaking slag produced every year. Based on this idea, they have carried out studies in recent years and they found that silicon and iron in the slag could be extracted into seawater effectively and play a positive role in the growth process of many algae. About the dissolution of the steelmaking slag, the Japanese scholars' research work mainly focused on the thermodynamic analysis of its dissolution possibility, and in the process of dissolution they tried to adjust the pH value of the seawater by continuously adding hydrochloric acid, which was deviated from the natural conditions of dissolution, and so the laws drawn under these special conditions can not give the identical guide to the practical application. Therefore, it is quite necessary to investigate the dissolution behavior of the steelmaking slag in the seawater at the normal pH range without adjustment to simulate the dissolution possibility under the natural conditions. In the present study, the silicon extraction behavior from the steelmaking slag was investigated and the dissolution kinetics in this process was also discussed in detail. Further studies were also performed here to evaluate the promotion of steelmaking slag on the growth of algae."

Jan 1, 2011

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995

By A. D. Zunkel

Increasing amounts of electric arc furnace dust (EAFD) are being generated worldwide as more steel is produced from electric furnace melting of galvanized steel scrap. In most countries, the management of this material is a costly technical, economic, and legal problem for minimill steelmakers. Many technologies and processes are being developed and implemented worldwide to manage this material to recover contained zinc, lead, and iron values and render it nonhazardous. These processes are pyrometallurgical, hydrometallurgical, or hybrid in nature. Some produce zinc oxide, some zinc metal, some lead metal, and some lead cement. Some are successful, some have failed, many are dormant. or abandoned, and others continue to be developed and emerge. This paper updates the current status of 20-30 processes in various stages of commercial application and development used worldwide to manage EAFD and recover its nonferrous, particularly zinc and lead, and ferrous values.

Jan 1, 2000

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Levent Özmen

Colemanite is a mineral containing varying amount of boron that is found in abundance in Turkey. It has a good possibility to be used as a flux in iron and steel industry. In this study a review of the use of colemanite, as a flux agent in steel production has been carried out and various related aspects such as its influence in metal-slag reactions, solubility of lime and magnesia in the slag are discussed along its performance in several points of views including its technical and environmental usage characteristics. Positive and negative factors of using this material as a flux are also underlined.

Jan 1, 2006

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By W. Gong

Their outstanding thermal stability and high energy product make Sm(Co,Fe,Cu,Zr),-type alloys attractive for advanced applications. The near net-shape production of Sm(Co,Fe,Cu,Zr), bonded magnets make them potentially superior to any magnets made by sintering. Although pioneering work done by Shimoda et al. and other investigators provide insights on the proper compositions and process control of this alloy system, additional work is still necessary to improve our understanding of alloy behavior at various processing stages and to increase the production yield during powder processing. In this paper we report on the development of anisotropic Sm(Co,Fe,Cu,Zr), alloy powders for the bonded magnet application. Our focus is on the development of a moderate coercivity powder requiring a relatively low magnetizing field to charge the magnets to their optimum Br, Hci and BHmax. The magnetic properties are related to the evolution of the microstructure at various processing stages and the average particle size and size distribution of powders.

Jan 1, 1997

By D. Quattrini

The aim of the present work is to present the gas chromatography (GC) as an alternative method of analysis in the thermal decomposition of calcium carbonate. Therefore, a furnace/GC on-line system was employed to study the kinetics of the reaction, measuring the CO2 produced in the decomposition. One of the advantages of the GC method is the possibility to perform an in-situ characterization and quantification of the gaseous products to obtain kinetic parameters, besides the method is simple and shows a good reproducibility. The decomposition of calcium carbonate was carried out in isothermal conditions at temperatures from 655 to 715°C with nitrogen as purge gas. Several gas velocities were used to determine the adequate flow that minimizes the effect of external mass diffusion as rate controlling step. It was made a preliminary analysis of the sample size influence on the reaction rate. The activation energy of the reaction was determined by Flynn method. The value obtained was in a good agreement with other authors. On the other hand, gravimetric measurements were employed for compare GC results.

Jan 1, 2006