Search Documents

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By Daniel Helm

The first industrial application of direct solvent extraction of nickel from hypersaline sulfate feed solutions has highlighted the need to investigate the influence of chloride on the extraction behaviour nickel in the presence of calcium using Versatic 10 and the solubility characteristics of gypsum. Temperature-solubility curves for gypsum in various aqueous electrolytes were prepared. The solubility of gypsum is increased significantly by the presence of sulfate ions, while chloride ions decrease it for a given temperature. The anion effects of chloride and sulfate on the extraction of calcium and nickel by Versatic 10 corresponded well with the complexing ability of the anions. It was shown that the presence of chloride shifts the extraction isotherms for both metals significantly to the left, while decreasing the selectivity of Versatic 10 for nickel over calcium. The loading of nickel onto Versatic 10 in this system was shown to be at a maximum within 3 seconds, while calcium extraction took between 4 ? 5 seconds to load to a maximum. Chloride ions had no influence on loading kinetics of nickel, but depressed the rate of calcium loading. It was shown that in the presence of an excess of nickel, calcium loading is effectively eliminated, and that calcium is scrubbed from Versatic 10 within 2.5 seconds of contact with nickel electrolyte.

Jan 1, 2003

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By I. A. Ibrahim

Ilmenite, in its natural form, is an inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite. so that it can be leached with dilute hydrochloric acid, can be enhanced by chemical reduction in solution using a suitable metal as a reducing agent. The present paper aims at the evaluation of an Egyptian ilmenite ore for the production of synthetic rutile by direct leaching with hydrochloric acid in presence of iron powder. In this process, the titanium and iron contents are dissolved; meanwhile, the dissolved titanium is hydrolyzed and re-precipitated leaving mainly iron in solution. Leaching conditions were optimized to obtain less iron in the final solid product. Addition of sufficient amount of iron powder during leaching reduces the dissolved Fe3+ to Fe2+ and reduces the dissolved Ti4+ to Ti3+. The creation of Ti3+ in solution is assumed to have a role in dissolving the ferric iron and hence increasing the reactivity of the ilmenite ore. Synthetic rutile of about 90% TiO2 and 0.77% Fe2O3 was obtained from ore with a grain size 100% passing 200 mesh and a 5-hour leach time with 20% HCl at boiling temperature (110°C) and 0.11 g iron powder / g ore.

Jan 1, 2003

By J. Ipinza

The slime formation with several metallic impurities from acidic electrolytes of copper has been studied. On fresh Pb-Ca-Sn anode surface firstly the formation of PbSO4 takes place, then, it is transformed in the conducting PbO2, which covers the anode surface. It has been experimentally established the formation of a manganese dioxide double layer at the anode; this double layer was always composed of a thick external layer of non-adhering and easily removable scales, and of a thin internal layer, which adheres relatively well to the surface of the electrode. It was found that manganese dioxides present in the slime were of different nature: a non-adhering layer produced by electrolysis (-MnO2) on the PbO2 surface and a pure chemical precipitation in the solution (-MnO2). When iron is present in the electrolyte on this last layer of manganese, lead sulfate was found. In the case of arsenic and antimony in the electrolyte the slime generated was found to be lead sulfate and amorphous compounds of those ions. The lower slime generation in Chilean EW plants could be due to the lower contents of iron and manganese in the electrolytes. It was found that this slime formation rate not only is due to the electrolyte composition but also to the poor control of operational parameters at EW plants.

Jan 1, 2003

By David T. Bunney

In .December of 1987, International Mill Service, Inc. signed an exclusive licensing agreement with Tetronics Research & Development Co. Limited of Faringdon, Oxfordshire., England to commercialize plasma technology which had been demonstrated in an EAF dust processing application. The intent of the process is to reduce and volatize the zinc, lead and cadmium oxides inherent in EAF dust and collect these elements as metals in an ISP (Imperial Smelting Process) zinc splash condenser, and to render the resultant slag an inert, non-hazardous material. With these objectives in mind, IMS started commissioning facilities in 1989 at Florida Steel in Jackson, Tennessee and Nucor-Yamato Steel in Armorel, Arkansas. This paper will address the commercial development and progress of the technology at these two installations. Process Description In the EAF steelmaking process typically the off gas stream is cleaned by some form of baghouse. The particulate collected is known as Electric Arc Furnace dust and has been designated by the U.S. EPA as hazardous waste number K061, once it leaves the collection system. This designation was given to the material due to the high toxic concentrations of lead and cadmium (nickel and chromium for stainless EAF dusts) inherent in the dust. IMS' method of operation is to locate the facilities on the client mill's property adjacent to the baghouse. The dust is transported directly to IMS via a closed conveyance system. This method enables the technology to be an additional processing step in the steelmaking process. Once the dust has been transported to the IMS facility, it is fed, metered and mixed mechanically in the feed conveyance system with a carbon reductant (typically coke breeze). The carbon reductant is approximately 10% of the dust feed rate. This mixture passes through the feed system and enters the furnace

Jan 1, 1992

By P. Koskinen

Outokumpu Oy has 30 years' experience in nickel production. It is mainly based on the technology developed within the company. The production chain starts from the mines reaching to the high-grade cathode nickel and the stainless steel manufacturing. As a multi-metal producer Outokumpu has the advantage to exploit from nickel raw materials also other valuable metals and intermediate products which can be processed at the company's various plants. The main source of nickel concentrate is nowadays the Enonkoski Mine started up in early 1986. It is the most modern mine in Finland being provided with the latest Finnish high-tech systems. Nickel concentrates are smelted at the Harjavalta Works using Outokumpu's internationally well-known flash smelting method. Also nickel containing residues and secondaries' are used as raw materials. The high-grade nickel matte from the smelter is then refined at the nickel refinery in a hydrometallurgical process, which was also developed by the company's own research staff. These processes have been continually improved and capacities gradually enlarged to 18 000 mtpy of cathode nickel. Besides plating, melting and superalloying purposes part of the nickel ends in stainless steel at the Tornio Works. The production was started in 1976 and has reached an established position on the European market.

Jan 1, 1988

By Jean-Pierre Birat, Ana-Maria Iosif, Denis Ablitzer, Olivier Mirgaux

"Integrating environmental considerations into the product traditional process design is now the major challenge for steel industry. Life Cycle Assessment (LCA) is nowadays considered as an appropriate method for assessing environmental impact and selecting new technologies to reduce CO2 emissions for steel industry.In this paper we propose a new methodological concept which combines LCA thinking with process simulation software in order to carry out the life cycle inventory of classical steelmaking process.Using Aspen PlusTM software, a physicochemical model has been developed for the integrated steelmaking route. This model gives the possibility to carry out life cycle inventories for different operational practices in order to optimise the use of energy, to calculate CO2 and other emissions and to control the mass and the heat balances of processes.It is also shown that such approach can be used to design and assess new technologies for steelmaking without large industrial application.IntroductionDuring recent years, it was recognised that CO2 emissions are the major factor of the global warming effect. In order to meet Kyoto requirements, the steel industry is embracing the challenge of sustainable development by improving its competitiveness and economic success while reducing its environmental impacts. Integrating environmental considerations into the traditional product design process, for powerful eco-efficiency, is now one of the major priorities for steelmakers.The European Steel Industry has measured up to this challenge by creating ULCOS (Ultra Low CO2 Steelmaking) consortium that has taken up the mission to develop breakthrough steelmaking process with the potential to reduce CO2 emissions (Eurofer, 2005). In order to develop technologies to reduce emissions, it is necessary to assess the environmental impact of the classical steelmaking route (coke plant, sinter plant, blast furnace, basic oxygen furnace, continuous casting and hot rolling)."

Jan 1, 2009

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By Kenneth L. Driggs

The 1988 shift in primary smelting facilities from low grade matte (35%) reverberatory furnaces to high grade matte (63%) flash smelting heavily impacted a very stable and successful converter operation. Low matte grade converter campaigns averaged 36,000 short tons of copper and revert production/consumption was in balance. The conversion to high matte grades necessitated oxygen enrichment of converter blast and revisions in operating practices. After two years of operational development, campaign life has risen to over 40,000 short tons and revert production/consumption is again in balance.

Jan 1, 1991

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By Masayuki Kudoh, Kiyotaka Matsuura

"Molten aluminum and nickel cast onto a steel block exothermically react and produce molten nickel monoaluminide, NiAI, which is simultaneously joined to the steel. The heat of the exothermic reaction is transferred to the steel block, and steel near the surface of the block is melted. The depth of the melted steel increases with both the initial temperature of the steel block and the thickness of the produced NiAI. Iron from the melted steel dissolves in the molten NiAI, and an intermetallic compound of NiAI-Fe pseudo-binary system is produced. During solidification of the intermetallic compound, it is strongly joined to the steel. The Ni.Al-Fe intermetallic compound has an excellent resistance to oxidation and corrosion.IntroductionAn intermetallic compound of nickel monoaluminide, NiAl, offers many advantages over conventional superalloys, such as higher melting temperature, lower density, greater specific modulus and higher thermal conductivity [1]. NiAl also exhibits excellent high-temperature oxidation resistance when doped with zirconium or hafnium, and excellent high-temperature corrosion resistance when doped with chromium or yttrium, that are superior to existing high temperature alloys or coating materials [1-4]. On the other hand, NiAI is significantly brittle at temperatures below 600 K [5-7], which is the most sigriificant disadvantage of NiAI. A possible way to overcome the disadvantage and to utilize NiAl as an environmental-resisting high-temperature structural material may be joining of NiAl to a ductile material."

Jan 1, 2000

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By C. T. Yavuz

Higher environmental standards have made the removal of arsenic from water an important problem for environmental engineering. Iron oxide is a particularly interesting sorbent to consider for this application. Its magnetic properties allow relatively routine dispersal and recovery of the adsorbent into and from groundwater or industrial processing facilities; in addition, iron oxide has strong and specific interactions with both As(III) and As(V). Finally, this material can be produced with nanoscale dimensions which enhance both its capacity and removal. The objective of this study was to evaluate the potential arsenic adsorption by nanoscale iron oxides, specifically magnetite (Fe3O4) nanoparticles. We focused on the effect of magnetite particle size on the adsorption and desorption behavior of As(III) and As(V). The results show that the nanoparticle size has a dramatic effect on the adsorption and desorption of arsenic. As particle size is decreased from 300 nm to 12 nm the adsorption capacities for both As(III) and As(V) increase nearly 1000 times. Interestingly, this increase is more than expected from simple considerations of surface area and suggest that nanoscale iron oxide materials sorb arsenic through different means than bulk systems. The desorption process however, exhibits some hysteresis with the effect becoming more pronounced with small nanoparticles. This hysteresis most likely results from a higher arsenic affinity for magnetite nanoparticles. This work suggests that magnetite nanocrystals and magnetic separations offer a promising method for arsenic removal.

Jan 1, 2006

By Neil E. Izatt, Ronald L. Bruening, Steven R. Izatt

"IBC has developed environmentally friendly Molecular Recognition Technology (MRT) processes to selectively extract, recover, and purify a wide range of metals from a variety of process streams. The incorporation of MRT into process flow sheets can improve the economics of the processes. MRT separations are effective even at low (mg/L to \i%JV) metal levels. MRT processes are sustainable, being economically viable, energy efficient, and environmentally friendly as well as having a low carbon footprint. Examples of MRT processes will be presented and discussed involving platinum group metals, gold, rhenium, and other metals of interest to the mining community.IntroductionA significant portion of the earth's precious metal resources has been moved during the past century from underground to above ground [1]. This movement has important economic, health, environmental, ecological, and sustainability implications for the earth and its population. There is concern that recycling of certain precious and specialty metals from end-of-life (EOL) electronic wastes (e-wastes), catalyst wastes, mining waste streams, and other waste products such as rechargeable batteries is not adequate to maintain supplies of these metals sufficient for future needs [2-4]. Improved metal recycling rates and more efficient metal recovery from the enumerated wastes would significantly reduce the amount of virgin metals that must be mined to support our lifestyle [5]. More efficient separation procedures in ore processing flow sheets and more effective recovery of metals from low-grade waste streams would reduce metal loss in the mining industry."

Jan 1, 2012

By Evan Jamieson

The conditions under which various iron(III) oxy-hydroxides phases precipitate from iron(III) chloride and sulfate solutions at ambient temperatures (<60°C) are reviewed. Many of these precipitates are slow settling and gelatinous but ultimately transform into other more stable or crystalline phases. The phase that forms depends upon the rate of precipitation and pH. A comparison has been made of the iron(III) oxides formed upon the neutralisation of various iron(III) solutions with caustic, slaked lime or slaked magnesia which provide different rates of neutralisation and slowly dissolving solids with localised high pH. Mössbauer spectra of ferrihydrites precipitated under these different conditions are compared and interpreted. Particular attention is paid to the settling rate and settled volume which is likely to relate to industrial thickener and filter performance. It is shown that in pure chloride solutions, poorly settling ferrihydrite is usually produced at 20oC regardless of the choice of base. However in sulfate solutions fast settling precipitates are produced using lime and magnesia but not with caustic. In mixed chloride/sulfate solutions, optimum settling rates occur when the molar ratio of [SO4]2to Fe3+ is about 1:1 and when the sulfate concentration is <0.20 M. It is proposed that ?dense amorphous basic iron sulfate? or well-ordered ferrihydrite is formed on slowly dissolving lime or magnesia surfaces. Implications for industrial liquors are considered.

Jan 1, 2003

By Hande Cavus, Ibrahim Yusufoglu, Cem Kahruman

"In this study, ammonium tetramolybdate (ATM) was obtained as the intermediate product of ammonium heptamolybdate tetrahydrate (AHM). The thermal decomposition mechanism of ATM was investigated under nonisothermal and isothermal conditions in air and inert gas atmospheres. Nonisothermal experiments were carried out by TGA/DTA/MS while TG was used for isothermal conditions. Characterization of the decomposition products were carried out by XRD and FT-IR. The thermal decomposition of ATM in air proceeds in a single step and forms M0O3 while [(ÍÇ4)2è]ïïï83Ìïè3 and molybdenum suboxide (Ìïè3.÷, ÷=0.025) were obtained in the first and the second steps of thermal decomposition in He, respectively. Activation energies, frequency factors and kinetic model equations were determined for thermal decomposition reactions. Fractional conversion-time diagrams were compared with diagrams drawn according to kinetic model equation.IntroductionM0O3 is usually used as catalyst in industry [1]. AHM is the basic source to produce molybdenum containing catalysts used in petrochemistry [2]. The oxides of Li, V, W, Te, Bi and Sn are doped in M0O3 to produce catalysts, which find commercial applications in the industry. The properties of M0O3 are affected by dissolution, settling, calcination, drying and thermal decomposition processes [1]. There are several studies in the literature about the thermal decomposition of AHM and the characterization of the decomposition products in different gas atmospheres and at various heating rates [3-19]."

Jan 1, 2012