Search Documents

Sanes are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. The purpose of this investigation was to study and develop a process to separate chromite sand and silica sand from reclaimed sands for a steel foundry. Physical separations were utilized to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches were examined. Experimental results are presented. A method was developed to separate chromite sand from silica sand after mechanical or thermal reclamation. The reclaimed sands are passed through a rare earth magnetic separator to separate chromite sand and magnetic impurities from non-magnetic silica sand. Chromite sand can be recovered from magnetic silica sand or magnetic impurities very effectively using a wet concentrating table. The applicabilities of the separation methods are discussed.

Jan 1, 1995

By P .. R. Ammann

A two-stage pyrometallurgical process has been developed for the recovery of copper (and other non-ferrous metals) from copper smelter slags. All types of slags, including highly oxidized, converter-type slags, are cleaned in an electric furnace which employs mechanical mixers to promote magnetite reduction and copper extraction at high rates. In a 10-ton pilot furnace, it has been demonstrated that slags can be cleaned to 0.2-0.3 per cent copper with economically acceptable usage of raw materials and energy; copper is recovered as a high-grade matte. Pilot plant data have been scaled up to a commercial furnace and engineering designs have been made for a furnace to treat 60 tons per hour of slag from a Noranda Reactor and the associated converters. Plans are being formulated for the construction of a prototype slag cleaning furnace.

Jan 1, 1976

By Robert Hanson, Mayur K. Patel

"Pneumatic conveying pipelines are used throughout a variety of industries, from food processing/packing to power generation plants, as an efficient means of transporting materials between storage and processing points. In general, different phases of pneumatic conveying exist when material is conveyed from point A to point B in a pipeline. This depends on the operating pressure and the material conveyed. Lean phase conveying exists when pipelines are operated at high airflow rates, relatively low pressures, inducing sufficient turbulence for particles to become entrained in the air stream. Thus, particles are conveyed along the pipelines at velocities in the range of IS-2Sm/s. Generally, the initial capital costs for lean phase system is low, however the running costs are high. The opposite is true for dense phase, high-pressure systems. In considering either conveying system, it is important that the rate of erosion of the pipeline be considered when designing such a system, since it is the rate of erosion that dictates the lifetime of components. In general, the high level of erosion occurs for lean phase flows, where high impact velocity contribute substantially to the rate of erosion as well as other processes such as particle breaking, if the particles are friable. This would lead to poor quality of material, not normally desirable. On a positive note, the process of erosion is used in other applications, which benefits from this process, e.g. abrasive guns.The failure, by puncture, of pneumatic conveyor bends in industry causes several major problems. Two of these are: (a) escape of the conveyed product causing health and dust hazard and (b) repairing and cleaning up after punctures necessitates shutting down conveyors, which will affect the operation ofthe plant, thus reducing profitability.The paper reports on modelling strategy used in the development of a modelling framework and the initial validation phases of the models incorporated within. The modelling framework encompasses Computational Fluid Dynamics (CFD) related engineering tools, based on Eulerian (gas) and Lagrangian (particle) approaches, to represent the two distinct conveyed phases, to represent the erosion process which is used to ascertain the lifetime of conveyor bends."

Jan 1, 2001

By T. Shoji

"The human history is characterized by social development based on mineral and energy resources, and many conflicts to take the resources by power. This is shown by not only world wars but also many local conflicts as well as international supremacy.IntroductionThe world population after B. C. 10000, which is summarized in several papers, is approximated by four straight lines on a semilogarithmic diagram as shown in Figure 1 [l]. The annual rates of increasing are 0.0041, 0.071, 0.53, and 1.85 % from the old and young periods. The boundaries among four periods are approximately B. C. 4600, AD. 1670, and 1930. The start of the second period seems to correspond to the beginning of agriculture and cattle breeding. Precisely speaking, the usage of natural energy resources such as woods and domestic animals already began, but is inferred to have become common after the age. The third and fourth periods are characterized by the common usage of coal and oil, respectivety. Not only energy resources but also mineral resources including gold, copper, iron and others are also important for the human history.Mineral and energy resources have supported the development of the .human civilization, and have caused many conflicts because of this reason. Every day newspapers report conflicts, such as Chechnya, East Timor and Ache. We can easily point out the facts that the conflicts closely relate to mineral and energy resources. Groznyj, Capital of Chechnya, is located on the western margin of Caspian oil field. Many mineral deposits occur in Kavkaz Mountains running south of Chechnya. Subsea oil fields occur in Timor Gap located between East Timor and Australia. Ache is also one of oil fields in Indonesia. It is very difficult to state present conflicts independently of a political view of point. For this reason let us try to historically review the relation between mineral and energy resources and international domination and conflicts [2] based on many papers [3]."

Jan 1, 2000

By Chen Song

In the experiments of purifying the solution of chlorine leaching from nickel concentrate with N235, the effects of organic phase composition on purifying efficiency have been studied. From the results obtained, the optimal organic phase composition is found to be 25%N235+12%isomerous alcohol +63%sulfonic kerosene (VIV) and the saturated content of cobalt in organic phase is7.95 g*dm3. And then the serial experiment is carried out. The results show that at the given organic phase composition, the purified solution contains p(Ni) >200 gm dm3, p(Ni)l p(Co) >50000 and the contents of Cu, Fe, Mn, Zn meet the technical criterion of standard nickel electrolyte. The cobalt chloride solution contains p(Co) >I10 g L-1, p(Co) lp(Ni)>50000 and the enrichment of cobalt has been achieved.

Jan 1, 2006

By Clemens Schmetterer, Patrick J. Masset

"The surface tension represents an important property for the modelling of high temperature processes. In this study the surface tension of two Al2O3 – CaO – SiO2 model slags and the influence of the admixture of 5 up to 30 wt.% FeO were studied. The surface tension measurements were carried out using the sessile drop technique on BN substrates under Ar atmosphere (10-6 atm O2) up to 1500 °C.IntroductionThe aim of VIRTUHCON1 is the virtualization of high temperature conversion processes, a task that requires thorough understanding of these processes. In many of these conversion processes slag plays an important role to control the properties of the product, to protect the reactor lining or simply as waste. Slag surface tension is one of the materials properties that is needed for the description of such processes, since it influences the interactions between the components in the reactor, e.g. at the slag – Fe interface in the blast furnace.Surface and interfacial tensions have thus received considerable attention in research, but the number of investigations in this particular pseudo-quaternary system is surprisingly low. Furthermore, the literature data are subject to different measurement conditions and techniques which complicates the data analysis and comparison.The slag atlas [1] offers a compilation of the available literature until 1986 (shown in Table I), but literature search has not revealed more recent studies of this system until now. For example, Elliott and Mounier [2] determined the surface tension of ACSF slags using the double tube maximum bubble pressure technique at 1200 °C. They kept their slags in contact with Cu-S-F mattes, and the slag therefore contained a certain amount of sulphur which acts as a surfactant and lowers the surface tension. The compositions of their slags were scattered over a wide composition range and they did not use a common ACS base mixture for their tests, either. The surface tension values vary between 417 and 446 mN/m, but due to the reasons just mentioned no trend in the measurements can be observed and the influence of FeO admixture on the surface tension cannot be deduced. Further information including the temperature dependence is available from Pavlov et al. [3], Ishchanov and Shushkov [4] and Murav’eva and Kaplun [5]; the diagram on page 446 in Ref. [1] has been drawn from these sources. Both positive and negative temperature coefficients are reported in these works. SiO2 is the only pure constituent that has a positive temperature coefficient [6], but a correlation of the temperature coefficient with the SiO2 content was not found to be conclusive."

Jan 1, 2011

By R. S. Celmer

The distributions of cobalt, molybdenum, copper, and selenium between nickel matte and silica-saturated iron silicate slag have been determined in the region of the metallic saturation boundary, at 1523 K. Results are given as a function of the composition of the coexisting Fe-Ni alloy and the activity of iron in the system. Under strongly reducing conditions, these minor elements display a marked preferential accumulation in the sulphide phase. It is shown that the dissolution of cobalt and molybdenum in slag follows an oxidative mechanism, and distribution equilibria are correlated with the oxygen potential. From these data, the thermodynamic properties of cobalt in nickel matte are computed. Further, comparisons of minor element partitions are made between the nickel and copper matte smelting cases under metal saturation conditions.

Jan 1, 1988

By Mingming Zhang, Ramana G. Reddy

"Carbon dioxide (CO2) is one of the most common by-products produced during light metals production. It is considered to be the cause of greenhouse effects. Efficient reduction of CO2 can help minimize the rate of global warming and improving energy sufficiency. In this paper, a novel light metal production process was developed using ionic liquid electrolytes. This process has significant advantages compared to the traditional high temperature processes such as zero CO2 and CF4 emission, low energy consumption due to the low temperature operation and nonconsumable electrodes. Two types of anode materials (graphite, extruded carbon) were tested in electrolysis experiment. The results showed that both anode materials were stable (negligible weight loss). However, the extruded carbon was found to be superior to graphite in terms of current density and current efficiency. The calculated energy consumption for aluminum production was less than 10 kWh/kg at current densities up to 300 A/m2.IntroductionGlobal demand for ultra-light, ultra-strong, recyclable metals is growing as the world switches to low-emission vehicles, energy-saving devices and sustainable products. Aluminum demand is forecast to climb by 30 percent; magnesium demand by 200 percent, while for the emerging industrial light metal, titanium, the demand is expected to be at least double in the next decade. However smelting of light metals is the most energy intensive among all the steps of light metals production. For example, on an average it takes about 15.7 kWh of electricity to produce one kilogram of aluminum from alumina [1, 2, 3]. Advancements in energy efficiency have been steady, but slow, and most U.S. aluminum smelting production operates at 95% current efficiency. Besides high energy consumption, another major concern of the light metals smelting process is the emissions of greenhouse gases (GHG). Electrolysis green house gas emissions in the Hall-Héroult process can be split into three groups: 1) reduction reaction emissions, carbon dioxide (CO2) and carbon monoxide (CO); 2) process upset perfluorocarbons emissions; and 3) hydrogen fluoride (HF) formed from the moisture (H2O) present in the raw materials [2, 3]. Hydrogen fluoride gas can be captured and returned to the cells by the alumina dry scrubbing system used in modern facilities. A total of 5.31 kilograms of CO2 is generated from the reduction process for each kilogram of aluminum produced in the average U.S. primary facility. The perfluorocarbon emissions are related to the “anode effect.” If the concentration of alumina in the bath becomes too low, other reactions between the carbon anode and the bath occur and tetrafluoromethane (CF4) and hexafluoroethane (C2F6) are generated. These gases have high global warming potentials (GWP), which is a ratio developed to compare the ability of each greenhouse gas to trap heat in the atmosphere relative to carbon dioxide"

Jan 1, 2008

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By Serdar Aksu, Fiona M. Doyle

"CMP will be an essential process in the production of integrated circuits containing copper interconnects. This study aims to improve our mechanistic understanding of the role that organic chelating agents might play in the reactive slurries used in copper CMP. Copper dissolution behavior in EDTA arid glycine was first examined by producing potential-pH diagrams for the copper-water-EDTA and copper-water-glycine 'systems. The results of potentiodynamic polarization experiments were then considered in light of these diagrams. . In-situ polarization experiments were conducted to gain insight into the electrochemistry of copper during dynamic polishing in slurries prepared from EDT A and glycine.IntroductionCopper has recently started to replace aluminum as the interconnect metal in integrated circuits. Copper interconnection offers faster and more reliable integrated circuits due to its higher electrical conductivity and superior electromigration resistance (1). The damascene method is used to form multilevel interconnects in the manufacture of integrated circuit devices with copper metallization (2, 3). Copper is deposited by CVD or electroplating into vias and trenches etched in the interlayer dielectric (IDL), over a diffusion barrier usually made from titanium, tantalum or their nitrides. Chemical mechanical planarization (CMP) then prepares the wafer for the next deposition step, by removing excess copper and planarizing the surface. During CMP, the wafer is rotated and pressed against a rotating platen covered with a polishing pad. Chemically active slurries containing submicron size abrasive particles (Si02, Al20 3, ceria, diamond, etc.) are applied. Both the mechanical action of the abrasive particles and the chemical action of slurry constituents remove material from the wafer surface. Planarization results because material is removed faster from protruding regions on the surface than from recessed regions. Since CMP can globally planarize .the entire wafer, it has become one of the key technologies for producing integrated circuits with copper metallization."

Jan 1, 2000

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By Kang Wan, Lei Tang, Jianchao Li, Jieyu Zhang, Minqi Sheng, Jifang Xu

"The viscous flow phenomenon in slag close to the liquidus temperature was considered. A simple approach that liquidus temperatures of melt could be derived from viscosity data was employed. The potential of this method for estimating the liquidus temperatures of pure water and binary alloy was demonstrated. The liquidus temperatures of the CaO-Alz03 based slags obtained from the second derivative method depends upon the number of viscosity values available at different temperature intervals. The results indicated that plots start deviating from the straight-line behavior at temperature as expect, and the second derivatives show the break points at a certain temperature, which is the liquidus temperature. Comparisons among the present observations as well as the characteristic temperature of the selected slags, which measured by the hemisphere method and DSC, indicated that it is possible to get a reasonable idea of estimate the liquidus temperatures from activation energies for viscous flow.IntroductionThe liquidus temperature of slag, which has a significant effect on the kinetics of chemical reactions and the slag-metal separation, is extremely important for metallurgical operations. Experimental measurements of the liquidus temperatures of slags are difficult, since slags invariable supercool. In addition, behavior of a single constituent in a multi-component slag is different in different circumstances due to its interaction with other constituents. Hence, it is essential to study the liquidus temperature of each particular slag resulting from a special process. Usually, the compositions of the slags aimed to the single liquid region of the phase diagram. However, the phase diagram of many slag systems, which back often to the 1950's, involves considerable uncertainties. Many liquidus temperatures are given as dotted lines in Slag Atlas [1]. Disagreements between the phase diagram and the reality have been found [2]."

Jan 1, 2013

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By Paul E. Queneau

The QS (Queneau-Schuhmann) copper converter is a gently sloped, stepped, horizontal kiln-type tilting reactor in which desired bath oxygen activity, compositional and temperature gradients are created by countercurrent flow of matte and slag phases through a series of controlled bubble plume, mixer-settler configurations. Flow of gas and slag is normally concurrent. Copper sulfide concentrates are top-fed, employing oxygen flash burners. Oxygen and oxygen-carbonaceous fuel mixtures are bottom-blown into the smelting bath through judiciously located, independently regulated submerged injectors. Composition and mass flow rates of injector inputs are controlled to produce bubble plumes of desired character, without jetting through and out of the bath. The mixer-settler pattern can be reinforced if desired by employment of suspended shallow baffles. State-of-the-art instrumentation provides timely information required to govern key process variables. The outstanding capabilities of the QS converter for coppermaking have now been indicated by the current success of industrial QSL (Queneau-Schuhmann-Lurgi) leadmaking reactors. Modified converter designs are employed for leadmaking, nickelmaking and steelmaking.

Jan 1, 1993

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By Y. Fautrelle, F. Felten, O. Metais, Y. Du Terrail

"We deal with the prediction of electromagnetically-driven turbulent flows by means of a Large-Eddy- Simulation method (LES). The model is applied in the case of a liquid metal pool submitted to a polyphase linear electromagnetic stirrer. We investigate two cases: (i) the frequency of the magnetic field is equal to 50 Hz; in that case the effects of the pulsating part of the Lorentz forces may be neglected; (ii) the frequency of the magnetic field is low (f= 1 Hz), then the oscillating part of the electromagnetic forces is taken into account. The LES predictions agree well with the mean velocity measurements, as does the standard k-a model. However, as for the turbulent kinetic energy predictions, there is a large discrepancy between the two models. When the oscillating part of the Lorentz forces is taken into account, the computations show that the fluid flow is sensitive to the unsteady part of the forces. We find that the mean velocity is not affected by the fluctuating component of the force. As for the turbulence parameters, the presence of the pulsating part leads to a significant reduction of the turbulent kinetic energy, whilst the turbulence length scale decreases.IntroductionElectromagnetic stirring is commonly used in various metallurgical processes. In continuous casting for example, it may improve the structure of the solidified metal products. Fluid flows generated by electromagnetic stirrers have been extensively investigated (1 ). As for numerical predictions, many works have been published on the subject. In most of the previous works, onepoint closure models have been used. The most used model is the well-known k-i:: model. Those models yield fairly good results as for the mean velocity prediction. However, it has two main drawbacks:(i) the turbulence is not predicted accurately,(ii) it is not well fitted for unstationary flows as well as transitional turbulent motions, where theReynolds number is moderate."

Jan 1, 1999

By Susanne Pignolet-Brandom

Fourteen samples of crushed Duluth Complex rock were characterized by the QEM?SEM automated scanning electron microscope image analysis system to evaluate the application of the system to mining waste rock characterization. The system can reliably distinguish the iron sulfides, the copper-iron sulfides and the nickel-iron sulfides. Calcite was distinguished from all other minerals except fluorite. The volumetric abundances were verified by comparing elemental abundances calculated using the QEM"SEM volumetric percentages and appropriate mineral compositions with elemental abundances determined by standard laboratory procedure. The pH and sulfate concentrations of rinse water from laboratory leach experiments correlated well with the mineralogical data.

Jan 1, 1989