Search Documents

By Michal Rehor, Vladimir Cablik, Peter Fecko, Tomas Lang

"1. Introduction The North-Bohemian Basin area is known for its largest Czech brown coal deposit. About 50% brown coal reserves have been exploited in the North-Bohemian Basin by the mining company of Severoceske doly, a.s. (North Bohemian Mines, j.s.c.) today. The opencast mining of brown coal naturally led to vast landscape damages. Therefore reclamation work has acquired great significance. The specific feature of Severoceske doly, a.s. mining is the fact that the mining has been realized in two geologically absolutely different localities. This fact demands even rather different methods of reclamations. The main problem at Doly Bilina localities is the occurrence of overburden rocks from the series of rocks of coal seams. These rocks are texturally light but large amounts of coal (cca 5 %) and sulphur (cca below 3 %) which makes the soil reaction extremely acid. If they appear on the surface of the dump, they create a phytotoxic area, reclamation of which requires special methods. Rocks from Doly Nastup Tusimice localities are more suitable to reclamation use, but texturally extremely heavy rocks with large fraction of physical clays appear there that can generate a sterile soil area. Their reclamation requirements are completely different from those on Doly Bilina phytotoxic areas. That is the reason of the application of some non – traditional restoration methods. This report briefly summarises the experience in application of fertilizable soils, power plant stabilizer, power plant ash and aerial sowing of charlock. The results are documented by the monitoring of the physical, mineralogical and pedological parameters of rocks in testing areas.2. Properties of Overburden Rocks in Opencast Mines Bilina and Libous The reclamation work methodology in the North Bohemian Basin is above all determined by the properties of overburden rocks which occur in the top horizon of the reclaimed sites. The research of the rocks reclamation properties dealt with four current mining localities in the central part of the basin. It concerned the Bilina and Libous mines. This chapter states the stratigraphic status properties of these sites with respect to reclamation availability. The total status of the area of interest is shown in the figure No. 1."

Jan 1, 2008

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By Carl A. Kuehn

At Carlin, Nevada, non-indigenous hydrocarbons were introduced as a bitumen phase which was mobilized due to burial under the Roberts Mountains allochthon. similarly, some indigenous organic matter was locally mobilized. Fluid inclusion and paragenetic data of veinlets formed during this hydrocarbon stage, combined with quantitative modelling or organic maturation, indicate that host rocks had evolved past dry gas conditions of around 1550 and l.l+0.2 Kb in the presence of CH4-saturated, highly saline brine by no later than early to middle Cretaceous time. All hydrocarbons present would have been rendered immobile under these catagenic conditions. Crosscutting relationships at several scales suggest that hydrocarbon mobility may have ceased prior to the intrusion of a series of dikes in the mine which have subsequently been altered and mineralized. Apart from subsequent oxidation, the current distribution and high maturity of carbon-rich zones were established prior to gold introduction. No Evidence has been found supporting proposed hydrocarbon "remobilization" during or after gold mineralization and alteration. The high density of the CH4-bearing fluid requires formation at high pressures (near 1 Kb) and precludes their formation as a result of the "cracking-off" of CH4 from organic matter during a thermal event associated with a shallow hydrothermal system. The density and composition of the fluid inclusions restricted to the early hydrocarbon-stages of the Carlin paragenesis are not unique to the sediment-hosted gold deposit environment of north-central Nevada. Similar inclusions are found in authigenic quartz crystals from Paleozoic carbonaceous shales in central Pennsylvania which have experienced normal metagenesis of indigenous organic matter due to deep burial.

Jan 1, 1987

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By George Oprea, Tom Troczynski, Joe A. Rigby, Waiman Lo

The refractory lining of the tuyere line in Peirce Smith converters have usually much shorter life in service than the rest of the lining, above or below it. There are already recognized chemical, thermal and mechanical factors which contribute to the wear of the lining. Our study presents the experimental results on microstructural changes occurring on these tuyere line bricks in a nickelcopper converter. The experimental bricks, after use at the tuyere line, were investigated using SEM/EDS and XRD techniques, to identify the mineralogical changes due to interactions with the nickel-copper matte or fayalite type slag at the process temperatures. The microstructural changes were correlated with physical and mechanical properties of the brick before and after use and a wear mechanism was suggested. Although the matte does not theoretically react with the mineralogical components of the brick, a partial oxidation of the Ni-Cu sulphides was identified using a line analysis by SEM/EDS in the densified layer at the hot face, which allows for mineralogical changes at the matte-refractory interfaces, with a high probability of microcrack formation due to the thermal cycling during use. These microcracks were also identified to open through inter-granular fractures parallel to the hot face, which appeared to be the main cause of lost lining during use. The reactions between the fayalite slag and refractory brick could eventually play a role in chemical dissolution of the brick only in the superficial layer at the hot face, as no slag components were identified deep into the brick.

Jan 1, 2009

By H. Bai, B. G. Thomas

"A three-dimensional finite difference model has been developed to study the liquid steel-argon bubble two-phase turbulent flow in continuous casting tundish nozzles. Experiments have been performed on a 0.4-scale water model to verify the computational model by comparing its prediction with velocity measurements using PIV (Particle Image Velocimetry) technology. The computational model was developed using CFX and then employed to investigate the effects of various casting process variables. A fast, simple inverse model to quantify relationships between those process variables was developed, based on interpolation of the numerical model results, using Bernoulli's Equation and advanced multivariable curve fitting methods. Predictions using this model compare well with plant measurements. The model has been applied to present trends and observations on the relationship between casting speed, tundish depth, slide gate opening, and argon gas injection rate. The results can also be used to predict .the theoretical steel flow rate through the nozzle, so that clogging conditions can be identified in the plant.IntroductionTundish nozzle geometry is one of the few variables that are both very influential on the casting process and relatively inexpensive to change. Designing an effective nozzle requires quantitative knowledge of the relationship between nozzle geometry and other process variables on the influential characteristics of the flow exiting the nozzle. This relationship depends on the flow pattern within the nozzle components. Most previous modeling studies of flow in the nozzle have focused on single-phase flow [1-4]. Argon injection into nozzle is an efficient and widely employed method to reduce nozzle clogging, even though the real working mechanism(s) are still not fully understood [5]. Argon injection may greatly affect the flow pattern in the nozzle, and subsequently in the mold. Therefore, two-phase flow modeling is needed to improve understanding of fluid flow in the nozzle."

Jan 1, 2000

By Carla Lupi

In this work, nickel-cobalt electrodeposition under galvanostatic conditions was investigated. Ni-Co alloy was electrowon from an acid sulphate bath containing 40 g/L Ni and2-8 g/L Co.. The effect of electrolyte composition, current density, temperature, solution pH and presence of buffers such as H3BO3 and (NH4)2SO4 on Co content of the binary alloy has been investigated. In particular, current densities ranging from 180 to 400 A/m2 and temperatures ranging from 27 to 60°C were tested. The composition of Ni-Co alloys may be diversified through the selection of process parameters. The experiments show that the highest cobalt content of the alloy is reached by using a buffer free electrolyte without solution pH control. Though, in these conditions, the most homogeneous, fine and regular deposit morphology is obtained, energy requirements are the highest in tests lasting just two hours.

Jan 1, 2003

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By R. Chiarizia

Third phase formation, i.e., the splitting of the organic phase in two layers, is a common feature observed, under conditions of high loading, for many solvent extraction systems of both analytical and industrial interest. Although this phenomenon has been investigated in a large number of works, a structural and physico-chemical description is still lacking. In this work, small-angle neutron scattering (SANS) data for the tri-n-butylphosphate (TBP)-n-octane,Th(NO3)4-HNO3 solvent extraction system have been interpreted using the Baxter model for hard-spheres with surface adhesion. The increase in scattering intensity in the low Q range, observed when increasing amounts of HNO3 and/or Th(NO3)4 are introduced into the organic phase, has been interpreted as arising from interactions between small reverse micelles containing three TBP molecules plus solutes in their polar core. This intermicellar attraction, under appropriate conditions, leads to third phase formation.

Jan 1, 2003

By K.H. Song, H.T. Son, H.S. Kim, W.Y. Kim

In order to evaluate the grain refining and mechanical properties due to severe plastic deformation (SPD), this wrok was carried out. Convential rolling (CR) and cross roll rolling (CRR) as a SPD method were introduced, and NI-20Cr alloy as an experimental material was chosen. The materials were cold rolledto 90% in thickness reduction ans subsequently annealed at 700oC for 30 min to obtain the fully recrystallized microstructure. For annealed materials after cold rolling, electron back-scattered diffraction (EBSD) analysis was carried out to investigate the grain boundary characteristic distributions (GBCDs). CRR process was more effective to develope the grain refinement relative to CR process, as a result, grain size was refined from 70 um in initial material to 4.2 um (CR) and 2.4 um (CRR), respectively. These grain refinements directly affect the mechanical properties improvement, in which microhardness and yield and tensile strengths were significantly increased than those of initial meterial.

Jan 1, 2012

By T. A. Venugopalan

The &apos;Hall-Heroult&apos; Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By Y. A. Chang

The objective of the present study is to evaluate and compile the relevant phase equilibria and thermodynamic data reported in the literature for the ternary system Cu-Fe-S. It is hoped that the results presented here will be useful to practising engineers and scientists in industry who are attempting to improve continually the existing processes of copper extraction and refining. At the same time, the present work will undoubtedly reveal the lack of some basic data which are important for the improvement of our existing extractive processes. Lastly, this work will also show that the development of theoretical models for the alloy phases in the Cu-Fe-S system is essential before complete consistency between the phase equilibria and the thermodynamic data can be achieved.

Jan 1, 1976

By Qingyu Deng, Shiwei Ma, Guibao Qiu, Hua Wang

"The flow behavior of the blast furnace slag bearing titanium, like viscosity, play an importance role during the iron-making process with the vanadium-titanium magnetite, which is a very special minerals in Panzhihua, China. The dependency of the viscosity on the chemical composition like TiO2, Al2O3, MgO, binary basicity (CaO/SiO2), temperature, reaction time were studied. The experiments showed that the viscosity decreased with the increase of TiO2, MgO content and binary basicity, and it increased with the increase of Al2O3 content and temperature. The viscosity showed a slight decrease within 60mins’ reaction with graphite crucible, however, it increased rapidly afterwards with the formation of Ti(C, N).IntroductionThe ordinary iron ore has been an essential part of raw materials for vanadium-titanium magnetite smelting in Panzhihua to avoid a series of problems, such as slag thickening, adhesive bond of slag and hot metal, etc. The ratio of vanadium-titanium magnetite has been decreased gradually since 1970s, and has down to about 65% now. However, with the substantial appreciation of price of imported ordinary iron ore, Panzhihua Iron and Steel Group aims to increase the ratio of vanadium-titanium magnetite and decrease the dependence on ordinary iron ore in order to lower the cost of smelting process."

Jan 1, 2012

By James M. Lockwood

"Eureka Technology has developed and patented a technology for the recycling of EAFD. Through this process all constituents of the material become salable commodities or are returned to the steel making process. In transforming the EAFD ""waste"" stream into a ""process"" stream the Steelmaker eliminates potential liabilities and the uncertain future of current processes while further reinforcing its role as a recycler. This is a cost-effective and energy efficient technology that combines hydrometallurgic and electrolytic processes resulting in the recovery of salable metals. For instance, unlike pyrometallurgic processes, zinc is recovered in metallic form and no elements are volatilized. This on-site operation also eliminates expensive transportation costs. In summary this technology reduces the cost of dealing with EAFD by recycling material currently being landfilled.IntroductionWorld crude steel production reached a new record level in 2007 - 1.34 billion tons of which 31% was produced by EAF steel makers [1]. This resulted in the generation of over 6 million tons of EAFD. This steel byproduct contains significant amounts of lead, cadmium and other hazardous metals. In the United States the Environmental Protection Agency (EPA) has designated EAFD a hazardous waste (EPA waste code K061). With over 50% of steel production in the US coming from EAF steel making this byproduct represents the single largest source of solid hazardous waste generated."

Jan 1, 2008

By Salustio s. Guzman

The standard .free energies of formation of tin chlorides were estimated with reviewed and estimated basic thermodynamic data, and measured reversible potentials for the disproportionation of tin dichloride into metallic tin and tin tetrachloride. Values for cºp, Sº, Hº?-Hº 298, -(Gº - Hº298) /T,.Hºf, Gºf, and log Kp are given in tabular form, these estimations are compared with estimations reported in the literature.

Jan 1, 1985

By Yang Jian-guang, Deng Zi-xiang, Zhang Xu-liang, Li Jun-yuan

"Hyperaccumulator biomass harvested after heavy-metal phytoremediation must be considered as hazardous waste that should be contained or treated appropriately before disposal or reuse. As a potential method to detoxify the biomass and to convert this material to a suitable bio-energy resource, the hydrothermal upgrading process was applied to remove heavy metals and upgrading crude bio-oil from Pteris vittata stems and leaves harvest. Parameters such as material granularity, temperature, Liquid/Solid (L/S, ml/g), pressure, duration and catalysts were examined for their effect on the removal efficiency of heavy metals and upgrading efficiency of crude bio-oil. Maximum heavy metal removal efficiency of>99% and crude bio-oil upgrading efficiency of 83% were attained with an 200 mesh (75 µm) granularity, LIS 40:1and23 MPa at 380°C in the presence ofO.l mol L-1 K2C03 for 30 min. GC-MS analysis results show that the resulting bio-oil mainly consists of benzene 11 %, ketone 42%, alcohols 14%, alkene 15% and ester 11 %, etc., and the relative molecular weight distribution lies in 94-282, carbon number distribution lies in 6-18, calorific value is 32MJkg-1.IntroductionPhytoremediation of soil or water with hyperaccumulator has been extensively explored in recent years [1-4]. Living plants can clean up soils or waterways. This approach exploits the ability of various plant species to thrive in high metal environments where large amounts of toxic elements are accumulated, such as heavy metals, and is particularly appropriate when slow remediation of relatively low metal concentrations is acceptable. Advantages compared with existing remediation methods include the minimal site destruction and destabilization, low environmental impact, and favourable aesthetics; advantages compared with biosorption include continuous in situ regeneration of the biomass, and the ability of living plant cells to supplement passive sorption of metals with metabolic mechanisms of metal uptake and detoxification [5-8]."

Jan 1, 2014

By Songsong Wang

Recently, replacing Pierce-Smith converting process with the oxygen bottom-blowing continuous converting technology has become a new research focus. Based on the principle of Gibbs free energy minimization, the thermodynamic model of oxygen bottom-blowing continuous converting multiphase equilibrium system has been established. The elements distribution behavior is calculated at the same burden composition and operation parameters as the industrial production. The results show that the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in crude copper are 0.06, 0.0030, 0.070, 0.38, 0.39, 0.020, 0.017, 0.034, 0.010, respectively, and the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in slag are 0.53, 0.81, 0.020, 0.23, 2.5, 0.0048, 0.0010, 0.0030, 1.49, respectively. The calculated results agree well with the actual industrial production data, indicating that the model can be well applied in the oxygen bottom-blowing continuous converting practice.

By Sven Eck, Andreas Ludwig, Menghuai Wu

"Phase separation is a frequently occurring phenomenon during solidification accompanied by melt convection, sedimentation or, in the case of two unmixable liquids, a Marangoni driven motion. In order to describe these phase separation phenomena a two-phase volume-averaging model was employed for globular equiaxed solidification of binary alloys and decomposition and solidification of hypermonotectic alloys. The model considers nucleation and growth of equiaxed grains or second phase droplets, motion and sedimentation of grains or droplets, feeding flow and solute transport by diffusion and convection. It allows the prediction of macro segregations and the distributions of grain size or droplet size. Evaluations were made by comparing the numerical predictions with experimental results. For example it is shown that the numerically predicted grain size distribution in a plate casting (Al-4wt%Cu) agrees reasonably well with the experimental analyses.IntroductionModeling of metallurgical processes is a rapidly expanding field and the research activities in the last decades cover a wide range of areas including melt pre-treatment, solidification and subsequent manufacturing routes. Among those activities solidification stands in the central position, because the primary structure of the materials, and even many defects such as porosity, (macro or micro) segregation and inclusions form during solidification. Those primarily formed structures or defects once existing are difficult to be removed or modified by the subsequent material processing.Solidification is a multi-disciplinary field involving thermodynamics, fluid dynamics and solid mechanics, heat and mass transfer, and other disciplinesr1 -31• One of the most challenging problems in solidification modeling is the complex interactions between physical phenomena occurring on different length scales ranging from atomic rearrangement over single crystal-melt interactions to heat extraction, momentum and species transport at the system level. Modeling an industry process on atomic scale is umealistic, even on grain scale (e.g. phase field method) it would need another 40 years to be able to model the exact grain morphology in a casting space envelope of 10x10x10 cm3 [ 4]. Therefore, the realistic models for industry process are based on the solution of the macro transport equations (mass, momentum, enthalpy and species) on system scale. The microscopic phenomena such as thermodynamics, nucleation law, crystal growth kinetics and interactions at the liquid-solid interface are considered with simplified models, which are coupled with the macroscopic transport equations."

Jan 1, 2004