Search Documents

By I. B. Scorzelli

The aim of this paper is to make a detailed mineralogical characterization of a typical brazilian xenotime and zircon from the Pitinga Mine using SEMIEDS techniques, On the other hand, superficial pretreatments with HCI, HN03 and HF were done to evaluate the modifications on surface compositions and the morphology of the particles for flotation purposes, The studies showed that both xenotime and zircon present very small inclusions of thorite; zircon is strongly metamictizated given rise to malacon. The HF pretreatment deeply affected the morphology of the particles as well as the surface properties in relation to flotation.

Jan 1, 1996

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By Elliot Schwartz, Julian Szekely

"In this paper we describe an experiment that was recently performed on the IML-2 Space Shuttle mission in which the thermophysical properties of molten metals were measured using electromagnetic levitation. In the planning of these experiments calculations had to be performed to predict the levitation and stirring forces, heating rates, sample deformation, and internal flows within the sample. These predictive calculations were essential for both the planning of the experiments and for the re-planning of experimental runs during the actual Space Shuttle mission.Introduction""Materials Processing in the Computer Age"" involves the use of mathematical modeling to obtain a quantitative understanding of the phenomena that govern materials processing operations. Microgravity, or space shuttle experimentation represents a specific case in point here; the very high cost of the space shuttle flights, the very limited flight opportunities that are available, and the tight resources aboard a shuttle clearly mandate that these experiments be very precisely planned and that all possible opportunities for mathematical modeling be fully exploited.The purpose of this paper is to present the results of calculations performed for the planning of a space shuttle experiment involving electromagnetic levitation and wherever possible present a comparison of the computational predictions with both experimental measurements and asymptotic analyses. Finally we shall seek to discuss the practical implications of both the computational methodologies and the potential experimental findings."

Jan 1, 1994

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By Liyuan Chai, Bing Peng, Ji Peng, Di Yu

"Electric arc furnace (EAF) stainless steel dust has been classified as a hazardous waste by various government regulatory agencies as it releases heavy metals to environment. The solidification of EAF dust is to stabilize the hazardous components to the amorphous silica-alumina-based clays. The process of solidification is investigated and the softening temperatures of dust and additive clay mixtures are measured for economical thermal treatment. The results indicate that the mixture of dust and local clay with the ratio of 1:1 has the lowest softening temperature 1100 °C and it could pass the toxicity characteristics leaching procedure (TCLP) test for the environmental regulatory limits after thermally treated at softening temperature for 15 min. Major phases of thermal solidification product clinker are CaAl2Si2O8, (Fe, Cr)2O3, (Fe, Mg)(Cr, Al)2O4 and Al6Si2O13.IntroductionThe yield of stainless steels in China arrived to 10 million tons in 2006 and more than 0.2 million tons of stainless steel dust are produced annually. Approximately 1-2 wt.% of scrap charged to an electric arc furnace (EAF) enters the off-gases and then is converted into the dust and reported to the bag-house. The disposal or landfill of the dust becomes a serious environmental problem in China due to the increased production of stainless steels in recent years. The dust contains elements such as chromium (Cr), nickel (Ni), lead (Pb), zinc (Zn), cadmium (Cd) and their solubility in leaching media exceeds the environmental regulatory limits [1]. Even though easily feasible for low-grade MgO, it is not appropriate to stabilize the heavy metals from the heavily contaminated soils after the dust landfill [2]. Several dust treatment technologies have been developed and they can be divided into two types. One is to recover the metals from the dust [3, 4] and another is to stabilize hazardous components present in the dust [5, 6]. Recycling of the dust generated in EAF is a remediation option for cleaner production. Direct recycling of EAF stainless steel dust was developed to recover the metal value from the dust and protect the environment [7], but it was only suitable for the dust with high contents of Ni, Cr and Fe. As for the dust with low valuable metal content, thermal solidification is an appropriate choice for the dust treatment."

Jan 1, 2012

By A. M. Strachan

Capper Pass & Son Limited Was, until its recent closure, the world's largest producer of tin from secondary materials including solder drosses, non-ferrous smelter flue dusts, tin based metal alloys, residues and slags. Polonium-210, an alpha emitting radionuclide, was present in varying concentrations in some of the numerous feed materials processed by the smelter and refiner. The polonium-210 followed a complex path through the process flowsheet. This paper discusses the behaviour of polonium, both from its arisings in other smelters' process streams and through the entire Capper Pass smelting and refining circuit. The consequential personnel safety and environmental precautions necessarily taken in some areas of the process operation are outlined.

Jan 1, 1992

By Zvi Rivlin

Classical nucleation theory states that in first order phase transformations, such as liquid to solid transition, nucleation of the product phase starts with the formation of small, unstable clusters (embryos). When the thermodynamic barrier to nucleation is overcome, the embryos grow and attain a critical size, beyond which they are stable, i.e. they become nuclei. If nucle- ation does not occur, the parent, liquid phase remains in metastable equilibrium. At temperature lowers, undercooling increase and atomic mobility decreases. The viscosity change in the undercooled liquid may result in the formation of glassy state. As demonstrated in previous papers [I-21, in solidification involving surface nucleation of the product phase, as the case is in rapid quenching by melt-spinning, both nucleation temperature and nucleation time depend upon the number of atoms available at the isothermal surface in contact with the substrate. As a result of the thinness of the melt-spun ribbons, the embryo clusters that form at the freezing temperature may not be supplied by the amount of atoms necessary for their growth to critical nuclei sizes. In such extreme conditions, the liquid does not crystallize, it forms a metallic glass. A numerical simulation method is proposed for the reactions involved in embryo cluster formation and growth, at the atomic level. The simulation enables the caIcuIation of either the nucleation or the glass transition temperatures. Calculations made for the well-known glass forming CuZr and FeB systems afford prediction of the geometrical and thermodynamically conditions necessary for the formation of either crystalline or amorphous ribbons in melt-spun ribbons.

Jan 1, 1994

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By Adrien Antenen, Didier Villette

CITRON has developed a new process for the recycling of hydroxide sludge, household batteries, catalysts, automobile shredding residues, grinding sludge and other metal containing organic and inorganic waste. A pilot plant with a capacity of 1,000 tons per year has started operations in April 1998. In August 1999, an industrial plant became operational with an initial treatment capacity of 23,000 tons.

Jan 1, 2000

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Denise C. R. Espinosa

Rechargeable lithium batteries are one of the most promISIng technology in battery development. Although Li ion batteries have been used as an alternative to the more polluting and less performing Ni-Cd batteries, Li ion batteries have limited life and their disposal is uncertain. It is imperative that valuables from wastes, such as lithium, should be recovered. The main objective of the present work was to characterize secondary lithium batteries for cellular phones. This was done using unit operations of mining processing, x-ray diffraction (XRD), chemical analyses and the rmogravimetric analysis (TG). The unit operations were hammer mill grinding, knife mill grinding, size separation and magnetic separation. After the hammer grinding process, the plastic cases were almost intact, however, they have released the cylindrical lithium batteries themselves and these parts correspond to 70% of the total battery weight.

Jan 1, 2001

By S. Shrivastava

A structure based model has been developed for the prediction of viscosities of K20-B20, melts. These melts exhibit an anomalous behavior of viscosity with continuous variation in B203 content. A maximum and a minimum are observed at low temperatures, which disappear on raising the temperature above the softening range. The addition of K20 to the borate melts causes two opposing phenomena: (1) depolymerization effects and the related breakdown of network structure resulting in the formation of singly bonded oxygens, which weakens the structure and hence causes a decreases in viscosity, and (2) the formation of four coordinated borons (BO4 tetrahedra) which strengthen the structure leading to an increase in the viscosity. The structural changes taking place in these melts on varying the temperature and the alkali content have been reviewed and are incorporated in developing this model. The predicted values are in excellent agreement with the experimental values over the whole temperature and composition range.

Jan 1, 1992

By O. A. Ogunseitan

The contamination of aquatic ecosystems by mercury wastes is one of the most serious forms of environmental pollution associated with the metal mining and electrochemical industries. The transformation of inorganic mercury to alkylated species is a reversible bacterially-mediated process. The production of methylated mercury is of ?major public health and eco-toxicological concern because these forms of mercury are highly toxic ?and they bioaccumulate in aquatic organisms. We determined the response of the genetic determinants of mei:cury transrormation by Pseudomonas species (that predominate in contaminated soils and sediments), to the concentration and species? or available mercurfiations. By combining selective isolation and gene. ?probe techniques, the intrinsic genetic potential for mercury detoxification in a contaminated environment ?can be estimated. We determined that genetic units required for mericury volatilization (merA ?for mercuric reductase) are naturally amplified in response to mercury. Mercury-resistant bacteria that tolerate up to 100 ug Hg(Il)/ml of medium contain about 10 times more DNA fragments encoding merA than in unadapted bacteria. The exposure of bacteria to methylated.Hg (10 ug/ml lake water) produced increases (up to 10 times) in .genetic units, and higher levels of genetic expression (up to 50 times) per ml of lake water for the mercury reductase system, than on-induced lake water. The findings suggest that in environments where methylated Hg may accumulate as a result of bacterial activity, the reverse reaction which leads to the removal of mercury through volatilization from the system, may be achieved by inducing genetic ?amplification and expression of the mercuric reductase gene system.

Jan 1, 1991

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By Jafar Safarian, Merete Tangstad, Leiv Kolbeinsen

"Silicon and its binary alloys have several applications in metallurgical, chemical, photovoltaic and semiconductor industries. Silicon goes to its liquid state within its production, refining and when it is alloyed with other elements. Therefore, the characterization of silicon melts thermodynamics is important and useful. The liquidus and activities in several silicon binary systems have been recently calculated by the application of two liquidus constants, which were established using the experimentally determined liquidus data. In the present study, the thermodynamic properties of six silicon binary melts, which are simple eutectics, are calculated by analytical approaches. In this case, the changes in the partial and integral Gibbs free energies and enthalpies of mixing are calculated and compared with the experimental data in literature. The enthalpies are calculated by two methods and the calculation results are compared to the data from the literature. It is shown that thermodynamic properties of silicon binary melts can be accurately predicted without the use of complicated thermodynamic software.IntroductionSilicon and its alloys have several industrial applications. Silicon is used for making aluminium-silicon alloys to produce cast parts, mainly for automotive industry. Silicon in the form of ferro-silicon is used to deoxidize and alloy steel and cast iron. The photovoltaic (PV) industry has had a rapid growth in the recent years and silicon is the dominant material used for the fabrication of solar cells. Silicon is primarily produced through carbothermic reduction of quartz in electric arc furnaces and the produced metallurgical grade silicon (MG-Si) contains around 1 wt% impurities. It is further refined to produce solar grade silicon (SoG-Si) with above 99.9999 wt% Si to fulfil the chemical requirement for PV application. Since molten silicon is processed all along the metallurgical route, obtaining fundamental thermodynamics knowledge about silicon melts is valuable for the related industries."

Jan 1, 2012

By Jian Li, P. Liu, R. Zhang and J. Lo

In the past decades, focused ion beam (FIB) has evolved into a powerful microscope that provides capabilities that no other microscopes can offer. The combination of high-resolution imaging and stress-free ion beam cross sectioning provides valuable microstructure information both at the specimen surface and beneath. FIB techniques are also the preferred method to prepare site-specific transmission electron microscope (TEM) specimens. CanmetMATERIALS owns a world-class microscopy facility, where advanced microscopy work provides strong supports to research programs that cover a wide range of subject areas. This paper is aimed to provide a few practical examples of FIB applications in microstructure characterizations that include cross-sectioning and imaging, serial sectioning, and advanced TEM specimen preparation in materials research at CanmetMATERIALS.

Jan 1, 2015

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By Jun Chang, Jin-hui Peng, Jing Chen, Li-bo Zhang

The leaching of indium from refractory zinc oxide flue dust(ZOFD) is attempted to utilize microwave sulfating roasting process, followed by water leaching. The ZOFD and roasted product were characterized by XRD and SEM/EDS analysis. The effects of various roasting parameters, such as roasting temperature/duration, the proportion of sulfuric acid, as well as the leaching parameters such as the leaching duration and liquid/solid ratio, were assessed. The results indicate that nearly 97% of indium could be leached under the following conditions: mass ratio of concentrated sulfuric acid to ZOFD to be 0.5, roasting temperature of 150 ℃ and duration of 1.5 hours; while the optimal leaching conditions hold at temperature of 25 ℃ for 1 hour, with 4:1 of liquid/solid ratio. The indium leaching rate by the microwave roasting increased by 8% as compared with the conventional roasting process under identical conditions.

Jan 1, 2015

By S. Niyomwas, R. G. Reddy

"A mathematical model was developed to describe the plasma gas and particle dynamics and conversion yields. The velocity and temperature fields in the plasma were calculated by solving 1 the Navier-Stokes equations and the thermal energy balance equations. Conservation equations for the system species consider the multi-component diffusion and chemical reactions. Through the application of this model, temperature distribution, flow fields, and production rates were computed. The model was used to study the thermal decomposition of ilmenite in the non-transferred arc plasma reactor. The computed production rates of TiN from ilmenite using nitrogen and methane gas mixtures, are in the range of 5 to 100 x 104 kg/m3/s at 2500 KIntroductionThe widespread interest in thermal plasma processing has stimulated a great deal of research effort into the various aspects of this process, including plasma' spraying, thermal plasma chemical vapor deposition, plasma synthesis of fine powders, thermal plasma decomposition, plasma melting, and plasma extractive metallurgy.In the plasma synthesis of fine powders, the earlier experimental and theoretical studies aimed at predicting the final products1-5. Then it was followed by more recent investigation concerning the profile of plasma gas velocity, plasma temperature and concentration. In this regard, useful plasma processing models have been reported by numerous investigation6 -11 which were increased by both theoretical analysis and measurement.As a result of this work a reasonable plasma-processing model is proposed. It is to be noted that all the thermal analysis that has been made neglected the fluid -flow effects. Also, in the analysis aimed at the quantitative description of the fluid-flow field, the effect of heat transfer was not taken into account."

Jan 1, 2000