Search Documents

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms around a longwall gate-road system in an underground coal mine. Of particular interest was roof deformation over the headgate entry. The strata above and below the coal seam are very weak, carbonaceous mudstones that have planes of weakness oriented along the bedding. Visual observations of previous gate roads over several years suggested that deformation was time dependent and resulted in creep along joints or crack growth. Instruments were installed at a test site to measure deformation around the entry, strew changes in the pillar, and loads transferred to support systems. Multipoint extensometers, instrumented bolts, instrumented trusses, biaxial stressmeters, borehole pressure cells, and single-point extensometers were installed. Monitoring continued until the longwall face passed the test site by 38.7 m (127 ft). Results show that fracture zones arched over the entry from both ribs, most bolts and trusses were loaded past their yield point, and the largest change in secondary principal stress was almost horizontal in the pillar. Displacement measurements in the roof showed classic primary creep.

Jan 1, 1995

By M. Y. Fisekci

This paper concentrates on subsidence measurements, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suitable methods for these conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the net- work of laser surveying over the workings of the new hydraulic mine.

Jan 1, 1981

By Gabriel Walton, Sankhaneel Sinha

"Rib failures are a major hazard in underground mining. When pillars are subjected to loading, extensile cracks are generated parallel to the excavation boundary, which can manifest as rib falls. A common mitigation measure is to install supports, especially bolts, normal to the rib surface. The type and spatial distribution of these supports along the pillar is often based on experience rather than comprehensive analysis. Since conducting field experiments is often impractical and expensive, a convenient alternative is to perform 3D numerical modeling. In this study, FLAC3D has been used to capture the interaction of rib bolts and the failure processes governing the stability of pillars. An associated goal is to determine whether, at all, a continuum software is capable of modeling the effect of supports. The modeling involved two important steps: selection of a proper constitutive model, and, explicit simulation of rock bolts. Based on precursory work in the last decade, an S-shaped strength criterion was chosen that can describe the tensile fracture mechanism of rock at low confinement and shear failure mechanism of rock at high confinement. The built-in pile structural element in FLAC3D is a simplified representation of the complete bolt system. Hence, the different components of a rock bolt (i.e., steel, grout, steel-grout interface, and grout-rock interface) have been explicitly modeled within the rock mass and then tested for its ability to replicate the ground-support interaction behavior. INTRODUCTION Rib failure-related hazards and injuries have plagued the mining industry for decades (Mohamed et al., 2016; Iannacchione and Prosser, 1998). In highly stressed environments, excavation parallel cracks are the primary initiators of skin instability. In absence of any support, this failure can indirectly destabilize the excavation by increasing the exposed span of intersections and roadways. Over the last two decades, there have been numerous injuries (fatal and non-fatal) due to rib failures in underground coal/non-coal mines."

Jan 1, 2017

By Baogui Yang, Jie Yang, Anthony Iannacchione

"The cemented coal gangue-fly ash backfill technique (CGFB) has commonly been used to control subsidence damage caused by underground coal mining. This paper discusses the CGFB backfilling process used at the Xin-Yang coal mine, Shanxi Province, China. A general description of the components of the CGFB are provided. The reaction of the strata to the backfilling process is simulated with a scaled physical model based on the Xin-Yang conditions and verified with subsidence points on the surface. With the help of the cemented filling materials, the CGFB produces only a slight bend to the overburden roof strata over the longwall panel. Physical models were constructed at the China University of Mining and Technology, Beijing, to simulate actual conditions. The modeling results show minor fracture distribution in the overlying strata and lower abutment pressure development within the backfilling area. The effectiveness of the CGFB technique is verified by a reduction in the vertical surface subsidence measured above the backfilled area.INTRODUCTIONUnderground longwall mining is the most efficient underground means to recover coal resources and is used widely in China, the US, Australia, and Europe. However, this type of mining has introduced some serious environmental impacts. Perhaps the most significant environmental issues are the surface and groundwater impacts associated with the formation of the subsidence basin (Bell and Donnelly, 2006). Backfill technology has been used for years to mitigate subsidence impact. Simply speaking, the backfilling technique places filling materials into the void left from the extraction of coal. When this material is placed within the gob, it is capable of partially supporting the overburden until a new equilibrium is reached. Essentially, the backfill material inhibits crack development and expansion caused by the strata movement and mitigates damaging ground deformations.The cemented gangue-fly ash backfill (CGFB) is one type of novel backfill technology, consisting of cement, coal gangue, fly ash, water, and additives in varying concentrations. The CGFB is mixed on the surface, pumped underground through a pipeline as a slurry, and placed in the void behind the longwall shield under the protection of specially designed hydraulic supports."

Jan 1, 2018

By D. Newman

An underground limestone quarry, developed in the 1940's, transitioned from a surface quarry to an underground room-and-pillar operation. The quarry expanded to a second underground level when the reserves on the first level reached the property boundaries. The historical basis for the sill pillar thickness between the first and second level, pillar dimensions, and mining height was lost during the course of several changes in ownership. When reserves on the second level reached a five-year life, and plans were initiated for a third level, quarry management embarked upon a thorough evaluation of i. current ground control practices for the support of the immediate roof, ii. roof support in the declines between the surface, Level 1, and Level II, iii. pillar centers and pillar safety factors, iv. pillar alignment between levels, v. mining height within a level, and vi. the locations of declines to access future reserves on level three. The evaluation began with detailed mapping of the location and orientation of calcite veins, joints, fractures, and ground conditions in the immediate roof of Level II. The orientation and location of calcite veins, joints, and fractures on Level II were compared with similar mapping on Level 1, completed in the 1970's to establish whether these features were continuous and would be expected to affect conditions on Level III. Rock strength, physical properties, and fracture spacing were obtained from two (2) diamond core holes drilled from Level I to Level II and two (2) holes drilled from Level II to define the vertical extent of future reserves on Level III. The effort to characterize geological conditions was expanded to a rock mechanics investigation of the: i. performance of the current roof support, ii. optimization of roof and rib scaling, iii. calculation of safety factors for 416 pillars on Level II, iv. evaluation of future pillar centers and mining height within a level based upon pillar strength and pillar geometry, v. development of beam safety factors for the immediate roof on Level II, vi. identification of the most suitable strata for the roof in the future level three, and vii. use of LAMODEL to develop a large numerical model of overburden, inter-level, and total stress on the pillars in levels one and Level II with a stress "footprint" on the proposed level three. The characterization of engineering parameters and geological conditions resulted in changes to the: ? active operations in Level II regarding scaling ? equipment and scaling practices, ? pillar centers, ? mining height, ? raising the immediate roof horizon to avoid ? laminated strata in the current roof, and ? a change in rock bolts from a friction based system ? to active tensioned rebar. The planning and design of level three is ongoing and relies heavily upon the geological and engineering investigations conducted during the past year and one-half.

Jan 1, 2001

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Stephen R. Iverson, Jeffrey C. Johnson, Donovan J. Benton, Michael J. Raffaldi, Lewis A. Martin

"The NIOSH ground control safety research program at Spokane, Washington, is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First, photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application. Second, field photogrammetric data is compared to crackmeter data from a deep underground mine. Accuracies were found to average 8 mm, but have produced results within 0.2 mm of true displacement, as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation. Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.INTRODUCTIONNIOSH Mine Safety ResearchPhotogrammetry systems have been implemented by the National Institute for Occupational Safety and Health (NIOSH) as part of its ground control research to improve mine safety. Conventional monitoring of ground movement has typically focused on movement of a few discrete points that are marked or anchored to instruments. Loss of a designated point or anchor, or the ability to identify a stable point in an unstable area, have often frustrated monitoring efforts. NIOSH researchers are using photogrammetry to conduct full-field measurements of rock surfaces underground. Periodic measurements of the entire surface of a ramp allow patterns of displacement to be observed. Full-field measurements provide much more insight into ground behavior than point measurements.BackgroundPrevious work by Benton, et al. (2014) discussed laboratory calibration and verification testing of two photogrammetry systems being used by NIOSH researchers. Both systems utilize stereoscopic image pairing techniques for photogrammetric reconstruction. This paper discusses how a laboratory system was used to conduct volumetric analyses of testing of shotcrete panels with varying types of reinforcement. The laboratory system was found to be accurate to within 2 mm. Additionally, a field photogrammetry system was found to produce linear measurements within 1 mm of known lengths in laboratory conditions. This system is currently being used at a deep underground mine to observe ground support conditions and deformations that have occurred. This paper discusses comparison of preliminary volumetric measurements of rib deformation to laboratory tests, as well as comparison of the field system against a crackmeter installed across a fault surface where it intersects the ramp."

Jan 1, 2015

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By Kresho Galovich

Quinsam Coal Mine located in Vancouver Island, BC, Canada is mining the No. 1 coal seam at the 2 North/3 North mine and the No. 3 coal seam at 4 South Mine. This paper describes its geology and structure, mining and processing, development and depillaring practices as well as methods of roof supports under various geological conditions.

Jan 1, 2005

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Changshou Sun

The geotechnical properties of mining zones at Leeville Underground mine (or simply called Leeville mine through this paper) are different from one zone to another. The typical ground condition is poor to very poor. Therefore, an appropriate ground control practice is the key for the successful and smooth ore production at Leeville mine. Based on the available geotechnical data, the empirical and numerical methods are used to design the right ground support systems. The main ground control practice at Leeville mine includes geotechnical data collection, evaluation of the stiffness of the support system, selection of rock bolt types, design bolt length and bolting patterns, development of the ground support standards, and performance of quality controls on bolt installation to ensure proper rock anchorage, and strength of shotcrete and backfill. Through all these activities, an appropriate ground support system has been established and applied at Leeville mine for the past four years. So far, a good result related to successful ground control and smooth ore production has been achieved, although the system is still being improved. The authors of this paper will summarize the ground control practice conducted in the last four years and will discuss the procedures and standards of establishing the appropriate ground support systems for Leeville mine.

Jan 1, 2013

By J. K. Owens

As part of a larger research effort focused on ground control, the U.S. Bureau of Mines is currently evaluating the effectiveness of using stereological analysis for characterizing mine roof strata. Input for a stereological analysis of a rock mass is best obtained by scanning (imaging) the walls of clean drill holes using a video-imaging borescope or other video device. Two classes of features are being investigated: (1) Lithologic types that comprise the overall rock mass and (2) structural discontinuities (e.g., joints, foliation, bedding planes) within a given lithologic unit. In the former, the volume fraction of a given Lithologic unit in relation to the entire rock mass can be estimated. In the latter, the mean intercept length between adjacent structures and surface area density of the geologic structures can be estimated. Examples of sampling procedures and subsequent computations are presented for several situations using information collected from drill holes in roofs of underground mines. One such example is based on the trace of a cycloid curve used as a stereological sampling path on the cylindrical wall of a drill hole. Stereological measures, such as intercept length, volume fraction, and surface area density, are explained in the context of rock mass characterization.

Jan 1, 1994

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004

Roof conditions at Southern Colliery, the second Iongwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 m thick roof beam either bonded or detached, with either a 2 m or 5 m overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By Zhikai Wang, Wensheng Lyu, Peng Yang

"To better understand the mechanical behavior of the compression deformation of backfill under high stresses corresponding to large depths, consolidation compression tests were performed for cemented tailings backfill with a cement-sand ration of 1:10 and 30% water under confined conditions. After applying different loading stress functions from 0.5 MPa to 32 MPa, the final axial deformation of the test specimen of backfill was obtained, and the micromorphology of backfill was studied before and after consolidation by scanning electron microscopy. Additionally, fitting analysis was performed for backfill confined compression deformation data and device model constitutive equations by the minimum square law. The constitutive model was revised according to the analysis results. The research results indicate that, as the load increases, the void ratio e obeys the functional relationship e=alnt + b (where a and b are fitting constants and t is compression time). Under the high-stress conditions of confinement, the constitutive model of backfill consolidation and creep can be used to describe the creep behavior of the backfill. Under high-stress conditions, after the consolidation of the confined backfill, the space between the tailing particles diminishes, the particles becomes more compact, and particle slippage occurs. INTRODUCTION With the depletion of shallow mineral resources, the mining industry has gradually shifted to deep mining (Zhang, Li, An, and Huang, 2010). Furthermore, with the continuous introduction of sustainable development policies regarding development and utilization of mineral resources, the mining industry must protect the limited available land and make full use of mineral resources as much as possible (Sijing, 1994; Zhihua, 2009). Backfill mining technology offers an unparalleled advantage in fully recovering mineral resources, controlling pressures, and improving environmental protection. As a result, this method has been widely used in various countries in the world (Burd, 2002; Benzaazoua, et al., 2008). Of the underground mines in the world, 45% of the large and medium-sized non-ferrous-metal mines and 37% of the gold mines use backfilling (Fuhrman, et al., 2014; Khaldoun, Ouadif, Baba, and Bahi, 2016). In addition, 45% of underground non-ferrous-metal mines and 37% of the gold mines use the filling method (Mchaina, Januszewski, and Hallam, 2001). According to incomplete statistics, more than 80 metal mines operate at a depth of more than 1 km; the depths of several typical deep mines are shown in Figure 1 (Burd, 2002; Fall, et al., 2009)."

Jan 1, 2017

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

By A. Wahab Khair

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992