Search Documents

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By T. Mills, M. Evatz

Newmont’s Lone Tree Mine, located in northern Nevada, is an open pit gold operation supported by a standard truck and shovel mine production fleet (Caterpillar 785Bs and Hitachi EXs). Newmont continues to search for ways to decrease capital expenditure and lower operating cost, hence the implementation of the Ultra Light Body (ULW) concept. The fundamental idea associated with the ULWs is the increased payload potential. Economic justification comes from successful achievement of additional payload, within the truck’s rated GVW, without changing its loading and hauling characteristics. The increase in payload capacity allows equivalent tonnage movement using fewer trucks.

Jan 1, 2001

By Joseph L. Young, Richard A. Bohling

To keep Homestake's Bulldog Mountain silver and lead mining and milling operation in southwestern Colorado workable, natural ground water and decant water from the mine's sand backfilling operation must be continually pumped from the workings. Left untreated, this water exceeds maximum allowable levels for various contaminants that may be discharged to the environment. To comply with regulations, a National Pollutant Discharge Elimination System (NPDES) permit was obtained and a mine water treatment plant for heavy metals removal was constructed in 1977. Due to equipment capacity and operational problems, and the lack of on-site technical personnel and analytic equipment, the first water treatment plant could not consistently meet permit limits. In 1979, Homestake entered into a consent decree with EPA and the Colorado Department of Health, calling for the construction of a water treatment facility to meet NPDES permit limits. Initial construction began in the spring of 1980 and the plant now produces effluent acceptable for discharge.

Jan 12, 1981

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002

By Don Phelps, Dean Brox, Peter Procter, Andy Saltis, Tom Morrison, Jeff Pringle

The Greater Vancouver Water District is currently constructing the Seymour-Capilano Water Filtration Project to enhance the quality of drinking water in the Vancouver metropolitan area. The Seymour-Capilano Water Filtration Project comprises the 1,800 million litres per day Seymour-Capilano Filtration Plant, the 1,080million litres per day Capilano Pumping Station, twin tunnels with associated shafts, and the Capilano Energy Recovery Facility. The twin tunnels will convey raw water under pressure from the Capilano Reservoir to the Seymour Filtration Plant and return treated (filtered) water for distribution. The Twin Tunnels component of the project comprises twin, 3.7 m diameter, 7.2 km TBM bored tunnels, the 180 m deep Seymour Shaft as the main launch shaft, and two 4 m diameter, 268 m deep raise bore exit shafts at Capilano. The Twin Tunnels have been planned as predominantly unlined tunnels sited at depth entirely within granitic bedrock and cross under two major buried glacial valleys of breadths in excess of 1500 metres that are filled with glacial sediments to depths up to 200 metres. The maximum overburden along the tunnel alignment is approximately 400 metres. Comprehensive site investigations and studies were completed during the detailed design stage of the project. The construction of the twin tunnels started in the fall of 2004 and is planned to be completed by mid-2008.

Jan 1, 2005

By M. S. Klima, P. T. Luckie

Proper analysis of washabiity data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Feb 24, 1997

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

By F. Díaz-Fierros, D. Rubinos, M. T. Barral

The present work explores the reutilization of red mud, an industrial waste arising from the production of alumina, as a component of isolation technologies for hazardous substances. The work involved the study and optimisation of the geotechnical properties of red mud in conjunction with adsorption experiments of As(V) and Hg(II). The results from both types of experiments were integrated in a dispersion-diffusion model to calculate migration curves and minimum thickness of the red mud compacted layer. The geotechnical studies showed that compaction increased the stability and decreased the hydraulic conductivity of red mud barrier. Red mud sorbed high amounts of As (up to 44 mmmol kg-1) and Hg (up to 9.2 mmmol kg-1). The calculated minimum thickness of the red mud barrier was 1-10 cm for As and 2-19 cm for Hg, for an operation period of 35 years. The results obtained let to conclude that the reuse of red mud as a component of isolation systems of hazardous substances represents a viable alternative use of this residue.

Jan 1, 2011

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999

By Michael Karmis

The International Conference on Sustainable Development Indicators in the Mineral Industries(SDIMI 2003) was held May 21-23, 2003 on the island of Milos, Greece. The objective of this international conference was to assist the mining and minerals industries in their global transition to sustainable development. The main theme of the conference was the development, monitoring and assessment of sustainable development criteria for mineral operations. Emerging technologies were also presented that can assist in the development of criteria and performance indicators.

Jan 1, 2003

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By Eldon L. Abbott, Rebecca K. Bolan

The Florida Department of Transportation, Florida’s Turnpike Enterprise is studying the feasibility of a 1128 meter (3,700 foot) vehicular tunnel to provide direct access for Port of Miami traffic to/from I-395, I-95, SR-836 (Dolphin Expressway) and Miami International Airport. Both Bored and Immersed Tube tunnels were evaluated and re-evaluated for constructing two, two-lane, 11.9 meter (39-foot) diameter tunnels beneath the Main Shipping Channel lying between Watson Island and the Port of Miami on Dodge Island in Biscayne Bay, Miami, Florida, USA. Bedrock Geology of South Florida is predominately very permeable, vuggy limestone with sand seams and occasional voids. Groundwater inflows in deep cut-and-cover excavations, tunnel buoyancy, grouting, maintenance of Port operations and potential/possible environmental impacts to Biscayne Bay were significant issues.

Jan 1, 2005

By Tim O’Neil

The search for precious metals opened up the American West. And Nevada was right in the heart of this development. In the mid-19th century, prospectors seeking gold roamed the hills of Nevada and discovered the ComstockLode. The development of this huge silver and gold deposit began in1859 and was responsible for Nevada’s early entry to statehood. Mining was Nevada’s first industry. In more recent years, the Nevada mining industry has led the nation in gold, silver and barite production. Nevada also produces many other minerals. These include aggregates, clays, copper, diatomite, dolomite, gypsum, lime and limestone, lithium and magnesium compounds, perlite, salt and silica. Even today, Nevada’s mining industry continues to be a major economic force in the state. The mining industry has made more than $10 billion in capital investments in Nevada since 1985. And the value of Nevada’s mineral production last year was about $2.7 billion.

Jan 1, 2000

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow inby the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

Jan 1, 2007

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000

By Li Zhou

The kinetics of the dissolution of galena was studied by monitoring the mixed potential of a galena electrode in ferric sulfate solutions. The results show that the mixed potential of the galena electrode fluctuated with time in a regular pattern in a 0.1 mol/L Fe2(SO4)3 solution of pH 1.66 and in a 0.01 mol/L Fe2(SO4)3 solution of pH 2.33 at 35°C. The periodic accumulation and precipitation of lead ions at the galena electrode surface and the cyclical variation in pH at the galena electrode surface caused the oscillation phenomena.

Jan 1, 2008

By T. Arthur Palm, Stephen L. Bessinger

San Juan Coal Co. (SJCC) operates an underground coal mine near Farmington, NM. Continuous miners and a longwall produce 6.3 to 7.2 Mt/a (7 million to 8 million stpy). SJCC is owned and operated by BHP Billiton. The coal seam at SJCC has been shown to have a propensity for spontaneous combustion. As such, during the feasibility study for this project, it was elected to use a bleederless ventilation system on the longwall. Due to the combination of spontaneous combustion, methane liberation and, to a lesser extent, hydrogen sulfide, a typical wraparound ventilation system would not be appropriate. Three-entry gate roads are developed, and the longwall gob is sealed as mining progresses. SJCC uses a nitrogen injection system to continuously inertize the gob.

Jan 1, 2007

By Steve Kral

More than 111,350 mining and construction industry professionals from throughout the world gathered in Las Vegas, NV, March 19-23 for ConExpo-Con/Agg 2002 and IFPE 2002. The triennial event is the Western Hemisphere’s largest equipment show for the quarrying, aggregates, construction and ready-mixed concrete industries. Despite the difficulties in the world economy, ConExpo-Con/Agg 2002 attracted more than 2,450 exhibitors from throughout the world. This was an increase from the 1,882 exhibitors that were on hand for the 1999show. And this year’s show occupied more than 180,225m2 (1.94 million sq ft) of exhibit space at the Las Vegas Convention Center. This was an increase from the160,900 m2 (1.73-million sq ft) occupied at the 1999event.

Jan 1, 2002