Search Documents

By R. K. Singhal, H. Sahay

Introduction In terms of the world's recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world's total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada's total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By Tim Hurley

On Friday, May 27, 1983 at about 6 p.m., an avalanche occurred at the Revenue-Virginius Mine. Six mine personnel and two contract diamond drillers were trapped when the avalanche covered and blocked the portal, the only access into the mine. The San Juan Mountain Range in southwestern Colorado is an old volcanic caldera. It has dikes and other intrusions, many of which are mineralized with sulfide ores rich in silver, gold, lead, zinc and copper. Several peaks rise above 4,260 m (14,000 ft) and the district has been the location of avalanches dating back to prehistoric times. This is evidenced by the numerous snow-slide chutes that are infamous enough to be named on topographic maps.

Jan 1, 2006

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By M. Irish, M. Jahraus

Accurate prediction of gold (or other metal) production from a heap leach operation is essential to the economic vitality of any such operation. However, this is also one of the most challenging issues facing managers of these facilities. Three approaches to modeling gold production from the Valley Leach Facility (VLF) at Anglogold’s Cripple Creek & Victor Gold Mining Company are presented. Evolution of these modeling methods has been necessary as ore heights and volumes have increased. In addition, the complex geometry of the VLF presents additional complications to production modeling, Comparison of actual and predicted gold production are presented

Jan 1, 2001

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

By J. Trow

Dowsing is really IESG which inductively locates electric gradients (dv/dx) on the flanks of SP anomalies. "Sensors" are in one?s head. The "meter" consists of one?s body, limbs, and two $.69 welding rods. The method was calibrated near Mamainse Point, Ontario, where IESG-negative chalcopyrite-bornite-chalcocite-native copper ores reveal mineral zoning related to the IESG-positive Keweenaw fault, down which oxidizing solutions moved. In Michigan, the IESG-positive Keweenaw fault suggests that oxygen-bearing solutions from the Jacobsville Sandstone moved downward to oxidize hydrothermal sulfur to produce native copper, and to supply sufficient water to satisfy Walter White.

Jan 1, 1992

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982