Search Documents

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By John C. Schneider

During the past decade, operators and researchers have worked toward a better understanding of the mechanisms operating in flotation. As reported by W. J. Trahar in 1981, this work commenced with the operators determining a relationship between recovery and particle size. They defined three particle size ranges, that being fine, intermediate and coarse. It was noted that the fine and the coarse ranges had slower flotation rates than the intermediate range as demonstrated by their lower recoveries.

Jan 1, 1998

By R. C. Emmett

In extractive metallurgy, separation of insoluble solids from solutions is an important economic factor in almost all flow- sheets. This separation step can employ sedimentation, filtration (vacuum and pressure), or centrifugation. Since practically all systems require a relatively complete separation, multiple unit, countercurrent thickeners or vacuum filters are generally used.

Jan 1, 1974

By F. H. Mertens

The costs of an open-pit operation can be classified according to the following hierarchy : -overall cost of production (per ton of ore) -costs of basic operations and functions -costs of auxiliary operations -costs of machines and equipment -maintenance costs. Production cost is a measure of the open-pit mine performance and should be the final target of the management control. It is also a measure of the share of the mine in the processing stages.

Jan 1, 1990

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By F. A. Campbell

This paper reports on mineral facies, ore textures, distribution of iron in sphalerites, and fractionation of sulfur isotopes in the Anvil ore body, Yukon Territory, Canada. Because the detailed structure and stratigraphy, both regional and local, are being studied by the geological staff at the mine and members of the Geological Survey of Canada, these topics will be discussed only briefly. The results of our study of the Anvil ore body have implications on theories of the genesis of ore deposits of this type, and these will be discussed. The Anvil ore body is the largest and most significant of three lead-zinc discoveries in an area of the central Yukon where major lead-zinc deposits were unknown only twenty years ago. The Vangorda deposit consisting of 22 million tons was discovered in 1953, followed in 1954 by the Swim Lakes deposit consisting of 10 million tons. The Anvil deposit, which consists of three ore zones, was discovered in 1964. The total reserve at Anvil mine is 63.5 million tons, with an average grade of 3.4% lead, 5.7% zinc, 0.16% copper and 1.2 ounces of silver per ton. This study is concerned primarily with the number one ore body which is about 2,400 feet long, up to 1,100 feet wide and 300 feet thick.

Jan 1, 1973

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

The surface properties of eight coal samples were studied by measuring contact angles, coal oxidation, equilibrium moisture and film flotation. The penetration tests were carried out with do de cane, while dodecane and MIBC were utilized in batch flotation tests and in the simplified release analysis. Coal floatability results from the properties of coal organic matter and coal liberation. While the wetting of coal by water seems to be determined by the surface properties of coal organic matter, wetting by hydrocarbons correlates very well with the content of coal mineral matter.

Jan 1, 1992

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By John J. Simmons

There is considerable interest in the iron and steel industry in the development of technologies that can reduce carbon dioxide emissions, as the iron and steel industry is the third largest producer of carbon emissions in the world, after automobiles and the power generation industry. The E-Iron Iron Nugget Making Process, invented by Dr. Komar Kawatra and Dr. Tim Eisele, provided a major breakthrough in the iron making process as the process uses biomass in the form of hard wood or soft wood as the reductant in the place of coal. Dr. Kawatra recognized that biomass is rich in both carbon monoxide and hydrogen, two important reducing agents. This resulted in initial experiments conducted by Dr. Kawatra and Dr. Eisele in the laboratories of the Chemical Engineering Department of Michigan Technological University (Michigan Tech) that prepared self-reducing pellets with wheat flour as the reductant and limestone/dolomite as the flux. Initial results were encouraging so they extended their work to include hardwood, which is in huge supply in the forests of Michigan and Minnesota, as the reductant. Dr. Kawatra has also applied the E-Iron Technology to other iron bearing minerals to produce pig iron grade iron nuggets. He used the E-Iron Process to convert red mud, a high iron waste product of the aluminum industry, into pig iron nuggets with the rare earth elements reporting to the slag. This work resulted in a patent with Dr. Kawatra and Dr. Michael Archambeau named as the inventors. Dr. Kawatra then extracted the rare earth elements as a separate high value bi-product using oxalic acid, which he produced from carbon dioxide. Dr. Kawatra also conducted a test program that produced pig iron nuggets from New Zealand beach sands. The vanadium in the beach sands was retained in the iron nuggets, recoverable as a valuable bi- product in a separate process. The titanium dioxide in the beach sands reported to the slag. This demonstrates the potential use of the E-Iron Process to convert the large ilmenite reserves in Northern Minnesota into pig iron and titanium dioxide. Another use of the E-Iron Process discovered by Dr. Kawatra was its ability to produce iron nuggets from manganiferous ores. Dr. Kawatra was able to direct the manganese into either the metal or slag by adjusting process temperature. The above discoveries are included in several patents that were assigned to Carbontec Energy. This presentation will only address the use of the E-Iron Process to produce pig iron nuggets from steel mill waste and un-pelletized, mid-grade iron ore. Carbontec Energy Corporation agreed to sponsor additional research directed at improving this new technology that would later be trade named, The E-Iron Process. Carbontec Energy conducted further work that proved that the E-Iron technology could also convert steel mill waste into metallurgically acceptable iron nuggets. Carbontec also collaborated with the Lawrence Livermore National Laboratory and Purdue University Northwest to conduct a Department of Energy (DOE) sponsored program that would use their high performance computer capability to both verify and model the E-Iron Process. Purdue University Northwest reported that the E-Iron Process can produce pig iron nuggets with 85% less carbon emissions than a blast furnace. The E-Iron Process is similar to the ITmK3 process, developed by Kobe Steel, that also produces iron nuggets but uses coal as the reductant.

Feb 1, 2025

By Harold Bloom

The Mount Pleasant Mines, or Mount Pleasant Joint Venture as it is presently known, is located approximately 59.5 km (37 miles) south of Fredericton, NB, Canada. Earliest indications of mineralization were found in 1954, during a regional reconnaissance geochemical stream sediment survey carried out over large parts of New Brunswick and the Gaspé Peninsula. The regional geology of New Brunswick is shown in Fig. 1. This program, sponsored by Selco Exploration Co. Ltd. of Toronto was conducted by H. Bloom, H.E. Hawkes, J.E. Riddell, and J.S. Webb. At its conclusion in 1955, 30 significant anomalous drainages were identified for follow-up evaluation. A total of 4937 sample sites were occupied. Geochemical reconnaissance using stream sediment sampling was a new technique which had only been field tested the previous year in the Gaspé and the northern coastal area of New Brunswick. Sediments collected from known mineralized drainages were found to leave a train of anomalous heavy metals from 1.6 to 9.7 km (1 to 6 miles) in length. When the exercise was extended to a reconnaissance survey, the previously unknown mineralized prospect at Nash Creek, New Brunswick, was discovered, staked, and later drilled (Hawkes and Bloom, 1956). Although it did not come into production, the discovery left little doubt as to the viability of the method and led to the Selco sponsorship of the program for the following two years.

Jan 1, 1991

By D. S. Kimbal

The McCoy/Cove mine is located 48 km (30 miles) south of Battle Mountain, Nevada, USA, in the Fish Creek Mountains at an elevation of 1548 m (5080 ft), see Figure 1. Joseph H. McCoy first discovered gold at this location in 1914. This discovery led to the Gold Dome Mine which produced the first gold from this area in 1928. After the Gold Dome era, the land remained relatively dormant until Houston oil and Minerals Corporation purchased the claims from the Summa corporation and defined an ore body at the present day McCoy pit. In 1986 Tenneco Minerals (formerly Houston oil and Minerals corporation), sold the McCoy mine and adjoining claims to Echo Bay Minerals corporation. The Cove ore body was discovered soon after the sale to Echo Bay. Echo Bay expanded the heap leach operation and built the present mill which began processing ore in the fall of 1989.

Jan 1, 1993

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974