Search Documents

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By V. E. Housman

EPA's Mining Waste Section within the Office of Solid Waste is continuing to collect and analyze information on mining waste management practices. Starting in 1991, the Mining Waste Section has continued to conduct site visits and prepare case study reports on the waste generation and management practices of operating mines. In choosing sites to study, a reasonable attempt was made to provide diversity in mining commodity types, geographic regions, geology, climate, and environment. To date, EPA has visited the following mines: Asarco Troy (copper) in Montana, Newmont Rain in Nevada (gold), Cyprus Thompson Creek (molybdenum) in Idaho, LTV Steel (iron) in Minnesota, Phelps Dodge Morenci (copper) in Arizona, Doe Run Fletcher (lead) in Missouri, Brewer (gold) in South Carolina, IMC Four Corners (phosphate) .in Florida, Pennzoil Culberson (sulfur) in Texas, Nerco Cripple Creek (gold) in Colorado, Copper Range White Pine (copper) in Michigan, Magma San Manuel (copper) in Arizona, Colosseum (gold) in California, and several gold placer mines in Alaska, including the Valdez Creek Mine. EPA has prepared a case study report on each facility. The mine operators were provided an opportunity to comment on their respective site visit report and their comments have been included in' each respective report. These site visit reports have in turn been incorporated into technical resource documents which provide a detailed description of each mining sector. EPA is currently reviewing the technical resource documents and plans to release the documents in the Spring of 1994.

Jan 1, 1994

By Raymond A. Bradbury

A significant news item appearing in a coal mining journal in November 1969 stated simply that a Caterpillar D-333-CNA engine had received Bureau of Mines Schedule 31 approval. This item occurring at the time a new mining property in Martin County of East Kentucky was being prospected and prepared for mining, resulted in the manage-ment of Martin County Coal Corporation asking the question, "Why not use diesel equipment in our new operation?" Martin County Coal Corporation is part of the A. T. Massey Coal Company, Incorporated organization. The property being developed is on a 17,500 acre leasehold obtained from Pocahontas Land Corporation and lies in the Wolf Creek area of Martin County. The Norfolk and Western Railway Company built a 24-mile railroad into this undeveloped section of Kentucky to tap a huge reserve of steam coal. Duke Power Company is the customer who will take all of the production from Martin County Coal Corporation mines which ultimately is projected to be 2,000,000 tons annually. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton are being deep mined now and it is in those mines that the diesel haulage equipment was introduced. This paper will endeavor to trace the steps loading to the introduction of the first diesel-powered Wagner Mining Equipment Company ScoopTram in a coal mine in America. It will further elaborate on the features which make this unit a very versatile and useful utility unit as well as the safety features which are incorporated in the machine. The success of this first unit led to the placing of

Jan 1, 1972

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By John Barber

The Deep Ore Zone (DOZ) Mine is PT Freeport Indonesia's (PTFI) newest operation. Production at the mine began in September 2000. The DOZ Mine produces 25 kt/d (27,500 stpd) using mechanized block cave mining methods. The DOZ Mine has several major improvements when compared with previous block cave mines in the district. It has an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system. PTFI's copper and gold mining complex is located in the Ertsberg mining district in Irian Jaya, Indonesia (Fig. 1). The Ertsberg district is located in the Sudirman Mountains at elevations from 3,000 to 4,500 m (9,800 to 14,700 ft) above sea level. The topography is extremely rugged and rainfall in the mine area averages 3,000 mm/a (118 in./year). Freeport began production in the district in 1972 when the mill began processing ore from the Ertsberg openpit. Underground mining began in 1980 when the Gunung Bijih Timur-Ertsberg East (GBT) Mine was brought online using block caving methods. In 1991, the GBT Mine reached a maximum production rate of 28 kt/d (31,000 stpd). Ore from the mine was exhausted in 1994. The Intermediate Ore Zone (IOZ) was brought into production in 1994. It, too, used block caving methods and had a design rate of 10 kt/d (11,000 stpd). The IOZ is currently producing at a rate of 21 kt/ d (23,000 stpd). The DOZ was discovered in the mid-1980s by deep drilling from the GBT. The GBT, IOZ and DOZ deposits are all situated in the Ertsberg East Skarn System (EESS). In 1993, the first of several studies was completed that indicated that portions of the DOZ Mine could be economically mined using block caving methods. Limited development was started in 1995. Full-scale development and construction began in late 1997. The crusher and conveying system began operating during the first quarter 2000. The first of two main exhaust shafts has been com¬missioned, along with three of the four new main fans. The second exhaust shaft and fourth main fan will be in service by the end of 2001. Undercutting and production began in September 2000. The DOZ Mine will reach its design production rate of 25 kt/d (27,500 stpd) in 2003. A study is under way to determine if an ultimate production rate of 35 kt/d (38,500 stpd) is feasible.

Jan 1, 2001

By K. L. Purdy

Electron spectroscopy for chemical analysis (ESCA) was used to determine the-surface characteristics of products from operating Pb-Zn-Cu concentrators on the New Lead Belt of southeast Missouri and pure galena and sphalerite samples treated-with flotation reagents in concentrations similar to those used in the mills. The emphasis was on the action of surface modifiers such as Na2Cr207, starch, SO2, CuSO4 and NaCN in sphalerite flotation and in the galena-chalcopyrite separation. The objective of the investigation was to monitor the relative oxidation states of the mineral and reagent constituents and correlate these surface concentrations and oxidation states with flotation theory and practice. ESCA was able to follow the action of all the modifiers except NaCN. The existence of PbCrO4 on the surface of galena conditioned with Na2Cr207 was verified. The Pb in the bulk PbS-CuFeS2 scavenger concentrate was found to be significantly more oxidized than the Pb in the bulk PbS-CuFeS2 rougher concentrate. ESCA was found to be most useful for investigating the actions of modifiers rather than collectors due to the large amounts of sulfur and background carbon already present on the mineral surfaces. After calibration for the particular chemical system of interest, ESCA can yield semi-quantitative analyses of the oxidation states of many elements (except hydrogen, and helium) present in the outer 10 to 25 A of a sulfide mineral surface.

Jan 1, 1975

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By Francis J. Kiessling

Energy and the conversion of potential energy into alternate forms is becoming a topic of household conversation for a larger segment of the world's population as mankind's desire for products derived from the vast array of technological developments continues to expand. The world's use of steel and the high energy consumption related to the production of steel promotes an awareness of the limitations of existing technology and a search for more economical alternates. Terminology such as (BF) Blast Furnace, (BOP) Basic Oxygen Furnace, (EAF) Electric ARC Furnace, (DR) Direct Reduction, (DRI) Direct Reduced Iron and (FC) form coke is becoming commonplace as alternates are being sought to alleviate the energy crunch. Coke production by various methods was developed as early as the seventeenth century in Europe to replace the disappearing hardwood forests that supplied the initial blast furnace fuel in the form of charcoal. In 1880, the Semet Solvay by-product coke oven design was introduced to the United States at Syracuse, New York, to supply coke for use in the production of soda ash, coke oven gas and its by products as the primary source of many organic processes. Although the Semet Solvay coke oven has not been marketed for decades, these coke oven batteries are in use today producing metallurgical coke, coke oven gas, and related by-products.

Jan 1, 1980

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By Josh Savit

Corporate responsibility already encompasses safety and compliance. No longer will companies be able to use differing standards of care to miners based on the country in which they are working. This is not only an issue of social license, but one of global risk management.

By John D. Smith

This paper describes how a knowledge of inherent rock characteristics can aid the mining engineer in his design of a mining method for a massive domelike structure. The paper shows how the pertinent rock characteristics were measured and analyzed and how the data obtained was used for design purposes. This analysis was conducted in 1964 in a producing salt dome, since that time, mine management has tried certain of the recommendations for mine design changes. The results of such changes are presented.

Jan 1, 1968

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By T. E. Wayland

Bentonites are clay materials composed principally of minerals in the montmorillonite group. Distinctive physical properties of the montmorillonite minerals are responsible for selected bentonite deposits having become the raw materials source of industrial clay products which are virtually essential to the maintenance of high production standards in the petroleum, foundry, taconite and other basic industries. These versatile materials have no suitable substitutes in either their major applications or in hundreds of speciality products, The economics of the bentonite mining industry follows closely the established pattern of other non-metallic raw materials. Aggressive competition, advanced technologies, progressive marketing techniques, substantial reserves, and vast unmeasured resources insure the continued supply of high quality bentonite to industry at bargain prices. The purpose of this paper is to discuss the geology and economics of bentonite deposits, summarize both major domestic mining districts and foreign deposits, and report significant results of research and development.

Jan 1, 1970

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

By Yassine Lahmadi, Edoardo Trivellato, Christian Chereau, Bénédicte Robert

Within the framework of the adaptation of the South-East European Technicentre (Technicentre Sud-Est Européen TSEE), SNCF Voyageurs appointed Pini with the project management mission (MOE) for the design and construction monitoring of a road tunnel. This investment has a dual function: during the site transformation phase, it facilitates the work logistics (and shorten traffic flows); and in the operating phase, it is intended to ease all movements on the site over the long term. This is a limited-length gallery (50 meters) to be performed in conventional excavation below Poniatowski Avenue (Paris 12e). The excavation, crossing the entire width of the boulevard, constitutes a major challenge, given the very low coverage (less than 5.5 m), and the surrounding main infrastructures. The same project mis- sion includes the design of the tunnel accesses, via reinforced-concrete frame structures. The targeted design questions several aspects of its execution framework, and particularly, continuous operation must be guaranteed to the neighboring networks during the works. The installation of an umbrella- pipe all along the excavation profile, the progression in divided sub-sections, and the implementation of a complex monitoring system are hence key elements for limiting and controlling any deformation. An exhaustive 3D finite element modelling was performed, taking into account the detailed phasing of construction (pre-support, excavation in divided section, preliminary support and definitive lining), to dimen- sion the structures, and, overall, to analyze the impacts on the neighboring structures and facilities. During the execution phase (planned for mid-2024), monitoring activities with back-analyses as close as possible to the works are planned.

Jun 23, 2024

Iron ores may be upgraded by flotation of iron oxides or siliceous gangue using either cationic or anionic collectors. The electrostatic mechanism of adsorption can account for the complex chemistry involved. In industrial practice, only cationic silica flotation is used at present in North America. Some of the seemingly paradoxical phenomena of cationic silica flotation behaviors in meeting the demand for low silica concentrates are reviewed.

Jan 1, 1989

By Mike O'Drisooll

There is no doubt, if any existed, that the commercial minerals world has now moved into a new era of unprecedented challenges in the sourcing, mining, processing, trade and use of industrial minerals. Industrial (nonmetallic) minerals remain the often unsung workhorse of mineral commodities and specialist raw materials that frankly keep the world’s manufacturing industries ticking over, and everyday products we use in sound availability. They are also very much present among the so-called “critical minerals” necessary to advance cutting-edge developments in growing high-tech markets such as in energy transition: for example, lithium, rare earths, graphite and fluorspar. Indeed, in the United States during 2024, industrial minerals again accounted for the majority share of total sourcing, and, yes, geopolitics. The last few years have witnessed a series of geopolitical issues that have impacted and continue to impact international trade in industrial minerals. Above all, it has been the threat and implementation of recent trade tariffs between countries that have been most damaging in creating a potential trade war. mine production by value at $72.1 billion, or 54 percent, followed by metals, 25 percent, and coal, 21 percent, according to the latest data from the U.S. Geological Survey (USGS). But right now, “industry resilience” seems to be the rallying call, with industrial mineral producers and traders facing straitened times from market slowdowns; environmental regulations; decarbonization and other sustainability issues; pressure to diversify; and near-shore mineral sourcing, and, yes, geopolitics. The last few years have witnessed a series of geopolitical issues that have impacted and continue to impact international trade in industrial minerals. Above all, it has been the threat and implementation of recent trade tariffs between countries that have been most damaging in creating a potential trade war.

Jul 1, 2025