Search Documents

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By Victor Romero, Steve Redmond

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2011

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By Dennis Molvik, Roberto J. Guardia, Brad Cowles, Rick Andrews, Robert A. Robinson

A 220-meter (m) segment of the Henderson/ ML King Combined Sewer Overflow(CSO) consists of two 1.8-meter-inside diameter (I.D.) pipe-jacked tunnels that pass beneath Interstate-5 and the BNSF and UPRR railroads. A seismic tomography survey was conducted to develop a 3-dimensional profile of the tunnel zone and better define potential obstructions. The tomography was conducted through three 11 cm high-density polyethylene (HDPE) pipes installed in a triangular pattern around the future tunnel alignments using horizontal directional drilling methods. The pipe-jacked tunnels have been successfully completed, thus permitting a comparison between the predicted obstructions and those actually encountered. The top HDPE tomography pipe was also used to monitor settlements with an experimental horizontal profiler above the advancing tunnels during construction and located two areas of ground loss beneath I-5 that were subsequently grouted.

Jan 1, 2005

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By Neville Slade, Doug Shumway, Dayan Anderson, Joe Siefke, Curtis James

The Mojave Desert is a particularly fragile ecosystem that faces several significant impacts. These include rapid housing development, overdrafted water supplies and loss of wildlife habitat — all a result of mining, industrial activity and urban sprawl. During the past three years, a diverse group of educators, natural resource managers and business leaders was assembled under the auspices of a local community college. This group’s goal was to provide unique natural resource education opportunities for the region.

Jan 1, 2005

? The economic health and national security of the U.S. depends on the continued availability of, and access to, reliable and affordable energy and mineral resources. However, America is hindered by a costly, inefficient and often redundant regulatory structure that thwarts domestic investment, expansion and job creation. The annual cost of federal regulations in the U.S. increased to more than $1.75 trillion in 2008; averaging $8000 per employee.(The Impact of Regulatory Costs on Small Finns, SBA, 2010) ? The complexity, uncertainty and delays within the current permitting system places the U.S. at a competitive disadvantage with many other countries that have both abundant mineral resources and a more welcoming business and regulatory climate. As a result, American and international mining companies often move overseas or across borders to invest capital, create local employment, and produce the critical minerals America must then import at higher cost, while sacrificing employment and economic stimulus. ? According to Behre Dolbear, the U.S. is ranked lowest globally due to the lengthy permitting period required before mine development can commence. (Where not to Invest, 2010).

Jan 1, 2011

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By S. J. Jung

The most frequent causes of accidental injury and fatality are carelessness and ignorance; and the most common accidents are haulage accidents, fall, drowning, and fire. However, in this modern day and age, severe injury has become the dire consequence of an ever-increasing number of industrial and mining accidents as well as sport-, military- , etc. Mine accidents have declined dramatically in number and severity through decades of research, technology, and preventive programs. However, preventing recurrence of disasters like those of the past remains a top priority requiring constant vigilance by management, labor, and government. The goal of the present research is to investigate and identify root causes associated with types of mining accidents (victim being caught by an equipment, bodily motion, over exertion, etc) and nature of injuries such as (sprain and strains, fracture, dislocation, amputation, etc). Further, we hope to discover the impetus of the root causes occurring more and more often in this modern day of technology and quality awareness. With the different dimensions of accidents and injuries brought into the fold, there is the need for researchers and mining operators to comprehend and better still visualize significant patterns of associations among these variables of interest. We assume that, there is a high correlation between many dimensions of nature of injuries and types of accidents. This suggested a principal component analysis to reduce the dimensions for easy and amenable interpretation.

Jan 1, 2012

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

Even though the economy of the United States remains in recession ? or not, depending on which economist you listen to ? muicipalities still need improved transportation, water and wastewater transit systems. And they are willing to spend the necessary funds on those systems, provided they are affordable, environ-mentally friendly and sustainable. From June 20-23, professionals in the tunneling and underground construction industry from around the world gathered in Portland, OR to learn new ways of providing those systems using the latest technology available. The North American Tunneling (NAT) conference attracted 803 attendees and 108 exhibiting suppliers of equipment and services.

Jan 1, 2010

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000