Search Documents

By G. J. Kringe

The results of a series of measurements of accelerations and guide-roller loads made on mineshaft conveyances are given, together with the predictions of these accelerations and loads based on a computer programme. The analysis of the measurements is described, and the results of the measurements and computer predictions when compared show reasonable agreement. Some parameters that increase the guide-roller loads are identified, and their effects are studied, together with some comments on the total loads. Finally, a possible format for a design specification is discussed, and some tentative design values are given.

Jan 1, 1986

By R. G. B. Pickering

The Faculty of Engineering at the University of the Witwatersrand and the Mining Technology Division of the CSIR have co-operated to define the problems associated with deep level mining and in this paper they will identify what they consider to be the critical areas requiring technological solutions. This perspective will then be applied to work currently being carried out by both the organizations and gaps for additional developments will be identified. Finally the Co-operative Research Centre methodology operating in Australia is described. The purpose of this CRC is to provide a vehicle for R&D co-operation to develop and implement technologies which will increase the competitiveness of the mining industry. A further objective is to develop an appropriately skilled human resource base.

Jan 1, 1996

The relationships between backfill-transportation parameters (solids concentration, velocity, and pipe diameter) and the wear rate of backfill-transportation pipelines is well understood. However, the degree of wear experienced by a pipeline depends not only on the transportation parameters, but also on the characteristics of the solids making up the backfill, i.e. the particle-size distribution, hardness, shape, and sharpness of the particles. Therefore, unless data corresponding to the specific wear rate of the solids are available, the determination of the wear rate for pipes transporting an uncharacterized backfill is largely guesswork. This paper describes an evaluation of particle characteristics with special reference to particle sharpness so that pipe wear rates can be correlated with solids of different size distributions and sharpnesses.

Jan 1, 1993

By M. G. Demmer

South Africa ranks among the top three mineral producing countries in the world, and yet the country's teaching and student population have a very limited knowledge of the mining and metallurgical industry. This is probably one of the major reasons why so few scholars elect to study mining-related disciplines at local universities, or to consider a career in the industry. Small mines Much interest in the development of small mines has been evident in the past few years, with junior companies taking the bull by the horns and moving in where larger companies found it uneconomic to tread or, indeed, where large companies are foresighted enough to see the advantage of smaller operations. Examples of small mines are to be found from Europe to Australia, in the Americas, and in

Jan 1, 1986

By R. R. Mankowski

The work described here is an extension of current theory applied to obtaining the power dissipated at the wavefront of a transverse disturbance traveling along a mine hoisting cable. A previously derived empirical relation is adapted to the present problem, and is solved by use of a Lagrange-type reference frame moving with the wavefront. As a result of tie limitations inherent in the original relation, only a lower-bound for the domain of predicted power losses is defined. A qualitative assessment of conditions leading to the undesirable effects of internal frictional losses at the wavefronts are discussed in terms of the operating environment found on typical mining installations

Jan 1, 1990

The sixth University of Stelenbosch (US)/University of Cape Town (UCT) Minerals Processing Symposium was held at the University of Cape Town on Friday, 7th August, 1987, and was sponsored by The South African Institute of Mining and Metallurgy (SAIMM). Once again the Symposium attracted a large number of delegates from the mining, metallurgical, and chemical industries. Uranium and electricity A symposium on 'Uranium and Electricity- The Complete Nuclear Fuel Cycle' will be held in Saskatoon, Canada, during 18th to 20th September, 1988. The Symposium is sponsored by the Canadian Nuclear Society. Electric steel The Institute of Metals, organizers of the 3rd European Electric Steel Congress, have announced that this important international event will take place in October 1989 at the Bournemouth International Centre.

Jan 1, 1987

By F. Ma, F. Yang, T. Zhao, P. Dai, Z. Shao, D. Zuo

With the development of modern digital technique, computers have been widely used to monitor and control in retrofitting traditional industries. In Chinese coal industry, some analog monitoring and control systems have been replaced by the modern computer digital systems. According to the development status of Chinese coal industry, this paper presents some technique and its applications of modern digital computer monitoring and control for safety mining production process. The technique has been used in the full digital monitoring and automation control for hoists, coal mining machines, belt transport machines, and whole coal mining production process. With the technique, it has been achieved the better economical and social benefits in safety mining production in China.

Jan 1, 2003

By R. T. Rudd

The impact of slimes-dam formation on water quality and pollution by R. T. RUDD*, B.Sc., AMI (S.A.) CE (Visitor) This paper discusses the mechanics of pollution by slimes dams in the gold- and fluorspar-mining industry, as well as that caused by coal dumps and slurry dams. The effect of coal mining on two typical rivers in Natal is shown and the implications discussed. The implications and trends of sulphates pollution on the Rand Water Barrage in the Vaal River are discussed. The spread of pollutants (sulphates and fluorides) from the Reef and elsewhere, and the impact on urban use and agriculture downstream of the barrage, are illustrated. Conclusions and future policy are outlined.

Jan 12, 1973

By M. D. Prendergast

Research into the ferrous metallurgy of Rhodesian Iron Age societies M. D. PRENDERGAST (Visitor) Iron-working was a widespread economic activity in Iron Age Rhodesia, and merits historical and metallurgical investigation. However, the research done so far has been incidental and poorly disseminated. This paper reviews the available evidence and the ways in which it can be interpreted by archaeologists and historical metallurgists. Particular attention is paid to smelting techniques and current metallurgical research, and brief suggestions are made for future research. v074n06p254.pdf

Jan 1, 1974

By J. Ungar, F. X. McGarvey

The selectivity of ion-exchange sites varies with the matrix of the polymer, the nature of the site. and the method of application. The effect of these variables on the recovery of uranium is examined. with particular attention to vinyl pyridine and to symmetrical and asymmetrical quaternary ammonium sites. The effect, on the loading. of high concentrations of chlorides in the liquors is discussed. and other components of the liquors that may cause fouling of the resin are also considered. The discussion is supported by the results of tests conducted on various types of resins. The economics of the process is discussed briefly.

Jan 1, 1981

By R. Hemp

The first part of this paper describes the collection of barometric pressure measurements in a mine and their statistical analysis, which shows the effect of variations in barometric pressure, both on the primary emissions of methane gas into the workings (whether from fissures or from the surrounding strata), and on the flow of air to and from large unventilated, or poorly ventilated, areas. The second part of the paper deals with a study, based on computer simulations, of leakage flows of air into and out of sealed areas, and the reduction of such flows by the use of adequate seals.

Jan 1, 1994

By M. Timucin

High-temperature phase relations in the Pb-PbS system were established by the quenching of samples equilibrated in evacuated and sealed silica capsules. The liquid-miscibility gap seen in some previously published phase diagrams was not observed. The thermodynamic activities of PbS in liquid solutions of this system were derived at 1473 K from the isopiestic equilibration of samples belonging to this solution series with Cu2S-PbS melts of known PbS activities. The behaviour of Pb-PbS melts was found to be compatible with a subregular solution model. This model also made it possible to obtain an analytical liquidus for PbS that was in excelent agreement with the experimental determination.

Jan 1, 1988

By R. E. Gundersen

Hydro-power-the use of high-pressure water as an energy source-offers tremendous benefits for environmental control in deep, hot mines. The extent of these benefits depends on the mining method, the selection of equipment to be hydro-powered, and the efficiency with which the coolth is extracted from the water and into the working environment. The engineering of hydro-power systems continues to receive much attention. However, this paper considers the environmental implications of using hydro-powered equipment, particularly with regard to positional efficiency. The integration of hydro-power with developments such as backfill, mechanization, and higher face-advance rates is discussed. Layouts are proposed that attempt to minimize the quantity of water in circulation by extracting the maximum coolth from the water.

Jan 1, 1990

By A. P. W. Briggs

Difficulties with the screening of large volumes of pulp to remove plus 600 /km material before the adsorption circuit and to retain plus 20-mesh carbon in the adsorption contactors have largely been solved, with the result that the plant can now handle its design throughput. The elution and electrowinning processes have been modified to simplify the circuit, but the regeneration of carbon remains unsatisfactory. The production of fine carbon in the plant can lead to increased gold losses, and this carbon must be collected and treated. Collection methods for fine carbon and some indications of the quantity of the carbon and its gold values are given.

Jan 1, 1983

By J. J. Geldenhuys

Premier of the North-West Province, Mr Molefe, foreign dignitaries and guests, ladies and gentlemen. It is a pleasure and also a special honour for me to have been invited here this morning to make this address. The xv Congress of the Council of Mining and Metallurgical Institutions is, by its very nature, an extremely important event for the international minerals industry. But I believe that this specific Congress assumes an even greater significance because of the profound and far-reaching changes that have taken place in South Africa this year. These are exhilarating times, a period when so much in our country has altered and when so much has to be done so quickly to build positively on our bold political decisions.

Jan 1, 1994

By R. R. Mankowski

The work described here attempts to underscore the importance of the time lag between the end of a loading phase and the instant a winding drum begins its acceleration phase. Traces generated from a computer-simulation model show that the amplitude of the stress oscillations occurring in mine hoisting cable during the constant velocity-of-ascent phase is a direct result of the temporal sequence employed between the loading and the raising phases. While current and early literature indicates that extensive work has been undertaken on the isolated effects of these two independent sequences, the literature does not appear to contain any documented evidence to suggest an optimal control or interfacing between these two dynamic regimes.

Jan 1, 1995

By B. M. Van Vliet

SYNOPSIS This paper outlines the principles involved in the regeneration of activated carbon for renewed use in the recovery of precious metals or the purification of water. While chemical methods are effective in restoring the activity of spent activated carbon containing only single or defined adsorbates, thermal methods have to be used when the spent carbon is loaded with a heterogeneous mixture of adsorbates such as those normally present in industrial process streams or effluents. The steps involved in thermal regeneration are described, together with the operating conditions that can be controlled to give the required degree of activation. Finally, an account is given of the structural changes that occur in a new or spent activated carbon during thermal treatment.

Jan 1, 1991

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991

By D. J. Adams, R. G. Gürtunca

In situ measurements and numerical modeling based on elastic theory showed that backfill stresses are considerably higher than originally thought. This has led to a change in understanding of rockmass behaviour. After describing previous work on the behaviour of the rockmass, this paper discusses possible reasons for the high stresses measured in backfil, and identifies the rockmass mechanisms possibly generating these stresses. It is concluded that the joints and the geological stratigraphy can lead to increased elastic convergence, and that the inelastic behaviour of the rockmass is also partly responsible for the increased closure measured in backfill. The use of an in situ modulus is suggested as an interim solution until a new computer model that allows for joints, different layers, and inelastic closures becomes available.

Jan 1, 1991

PREFACE During the past year, considerable effort was devoted to the implementation of the strategic plan that was adopted by the SAIMM in 1986. Good progress was made in a number of areas, while in others the foundation was laid for future progress. Key Objective of the Institute The key objective of the SAIMM is as follows: To identify the needs of its members and to initiate and give effect to the means whereby the requirements for technology and scientific knowledge of the minerals and metals section of the South African economy are satisfied; and to represent and promote the interests of its members.

Jan 1, 1987