Search Documents

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By R. R. Mankowski, F. J. Cox

Experimental results are presented on the longitudinal atenuation of a kinetic shock wave traveling along a typical mine hoisting cable. Mathematical curve-fiting of the results established these losses to be exponential and tension-dependent. The reflection and power-transmission coeficients of a typical winding drum were also investigated. The degree of penetration of an incident stress wave onto the coil of cable wrapped round the drum is shown to be governed by a second-degree relationship, and is solely dependent on the acceleration of the cable at the cable-drum interface. Although the investigation is limited to the testing of a single hoisting cable, certain qualitative trends that were identified can be generalized and applied to other types of hoisting cable with diferent geometries, elastic properties, and instalations.

Jan 1, 1986

By R. N. Guest

The Tromp distribution curve was used in an evaluation of gravity separators treating a synthetic ore made up of silica and marker minerals of various relative densities. The results pinpoint differences in the concentration of particles of different sizes, and indicate how the grade of a concentrate is likely to vary with particle size. An increase in the feed rate increased the efficiency of the 'waterless' spiral concentrator that was tested, but the multiport spiral concentrator tested was more efficient. Both spiral concentrators were found to be more efficient than the pinched sluice and the shaking table that were tested. The method was found to be a useful way of evaluating gravity concentrators, but, for ease of analysis, care must be taken in the choice of marker minerals.

Jan 1, 1985

By N. C. Joughin

Potential for the mechanization of stoping in gold mines by N. C. JOUGHIN B.Sc. Eng., Ph.D. (Rand) (Member) The basic requirements for stoping machines are identified first by examination of the mining rates and productivities attained in conventional stoping, and then by examination of a series of problem areas associated with the shape of the reefs, rockbreaking, rockhandling, and the support and design of the machines. Some of the more important machines being developed are described briefly, and their principal features are compared with the basic requirements identified in the first part of the paper. An estimate of the potential demand for the different types of machines is given.

Jan 1, 1976

By C. G. Hutson

The Zinc Corporation of South Africa (Zincor) were hosts to about forty members of the Institute at their works in Springs on Friday, 25th April, 1986. The programme, designed to give an overview of the industry and the part played by Zincor, comprised an introductory talk, a technical talk, a tour of the plant, and a luncheon. Radioactive waste in arid regions A conference on the disposal of radioactive waste in arid areas will be held in Cape Town during the period 7th to 12th September, 1986. It is recommended that engineers and scientists avail themselves of the opportunity to familiarize themselves with this relatively new multidisciplinary field of endeavor by attending the first ever conference of this nature to be held in South Africa. Iron control in hydro metallurgy The International Symposium on Iron Control in Hydrometalurgy will be held at the 16th Hydrometallurgical Meeting, from 19th to 22nd October, 1986, in Toronto, Canada.

Jan 1, 1986

By J. H. Bulloch

This paper describes detailed fractographic analyses of several specimens that had undergone corrosion-fatigue tests at high stress ratios in simulated pressurized water-reactor environments. The distribution and morphology of non-metallic manganese sulphide inclusions are shown to strongly affect the growth of environmentally assisted cracks (EAC), and certain features suggest that a hydrogen-assisted mechanism is responsible for the observed EAC growth. The incidence of transient EAC growth in isolated regions suggests that the critical conditions that trigger this type of growth are the 'right' local chemistry at the crack tips and imposed mechanical conditions.

Jan 1, 1987

By N. A. Barcza

Pointing out that South Africa needs to utilize its wealth-creating activities, together with local and international investment, to further develop its industries, the address asserts that the mining and minerals industries, especially in the manufacture of beneficiated products, offer the greatest potential for South Africa to achieve its goal. As many mineral-beneficiation processes are based on pyrometallurgical routes, the address goes on to describe some historical - pyrometallurgical operations and to indicate probable developments in the future. These include growth in the fields of both precious and base metals. After discussing environmental and recycling matters, together with manpower requirements, the address concludes that the major growth in the mining and minerals industries will occur in the manufacture of steel, stainless steel, ferro-alloys (particularly ferrochromium), aluminium, and titania slag.

Jan 1, 1996

By G. G. Stanley

Mechanisms in the autogenous mill and their mathematical representation by G. G. STANLEY, B.Sc. (Eng.) (Wits.), M.E. (Queensland), Ph.D., (Fellow) The special characteristics of the autogenous mill are stated, and a suitable type of model for the mill is presented. Details of the test plant and experimental techniques for obtaining the data for model development are next given. followed by a discussion of the methods developed for the computation of the model parameters, namely the appearance matrix, the abrasion and crushing breakage-rate functions, and the discharge-rate function. Examples of results obtained with the model are given, and finally there is a brief account of confirmatory work on a fullscale autogeneous mill.

Jan 11, 1974

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

By F. J. J. Blaauw

This paper discusses a bold venture into the use of interactive computer graphics technology as the foundation of an overall integrated mining managerial system. The wide range of applications that can be addressed through the use of this technology is highlighted, and some discussion of the major facts of this project, which is still in its early stages, is provided.

Jan 1, 1987

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By Y. Hwang, C Kang

To understand the effect of thermal loading from HLW on the groundwater flow nearby, the coupling of TH in an equivalent porous medium is studied. Results indicate that under given conditions the alteration of groundwater flow by decay heat is localized phenomena. More comprehensive studies are underway for THM coupling. Zum Verstandnis fur die Wirkung der thermischen Belastung von HLW in der Nahe von Grundwasserstrom, ist die Verbindung von TH in den entsprechenden porigen Medium erarbeitet. Die Ergebnisse zeigen, dass unter vorgegebenen Bedingungen die Anderung von Grundwasserstrom durch Zerfallwarme lokalisiert wird. Zusatzliche umfassende Arbeiten sind fur die THM Kupplung auf dem Wege. Pour comprendre l'effet du chargement thermique de HLW sur l'écoulement d'eaux souterraines tout près, l'accouplement du TH dans un milieu poreux équivalent est étudié. Les résultats indiquent que dans des conditions données le changement d'écoulement d'eaux souterraines par la chaleur d'affaiblissement est des phénomènes localisés. Des études plus complètes sont en cours pour l'accouplement de THM.

Jan 1, 2003

By F. E. Steffens

The application of kriging in assessing the area rainfall in a weather modification experiment is complicated by the presence of many zero rainfall recordings on a given day, and the fact that the variograms seem to be quite different for the rainfall on different days. Indicator variograms are shown to be directly related to two sets of conditional probabilities. Probability kriging is used in estimating the probability of rainfall amounts above any cutoff at any point

Jan 1, 1987

By G. J. Wright, M. J. Neale

As machines become more complex and vital to our way of life, any disturbance or failure of their proper functioning tends to have serious consequences. To prevent such failures, increasing attention is being paid to techniques for the monitoring of machinery condition or 'health'. Of the many methods available, examination of the lubricant and any particles it contains forms a basis for interpretation of the conditions of operation, and the rate and severity of degradation of the moving parts, in a machine. Many techniques of wear-debris analysis, such as spectrographic oil analysis and ferography, are available indicate the composition, shape, size, and concentration of contaminants in a lubricant. This paper reviews the important aspects of wear-debris analysis as an integral component of machinery condition monitoring, and gives an insight into the selection of appropriate techniques and the information that can be obtained from each.

Jan 1, 1987

By P. J. How, T. O. Hagan, M. F. Handley

Inelastic deformation of highly stressed rock in deep mines needs to be quantified in both time and space. Since most deformation occurs by shear, continuous monitoring of discontinuities in the rock from boreholes holds promise. The casing. Al interpretations of shear movements are based on a simple relation between shear displacement and the resulting change in tilt of the sensor. A prototype has been constructed and has undergone laboratory trials with satisfactory results. Underground trials will commence shortly. The instrument as designed has the potential for other applications, both in the civil-engineering and mining industries. paper describes an instrument that is both cheap and reliable, and capable of monitoring such shear movements continuously. The principle of operation is based on two capacitive gravity sensors mounted orthogonaly to each other in a sealed aluminum

Jan 1, 1988

By R. C. Urquhart, D. D. Howat, R. I. L. Guthrie

Heat losses from ladles during teeming by R. C. URQUHART, M.Eng. (McGiII), Ph.D. (Visitor). R. I. L. GUTHRIE, B.Sc. (Eng.) (London), A.R.S.M., Ph.D., D.I.C. (Visitor), and D. D. HOWAT, B.Sc. (Glas.), Ph.D. (Fellow) In an investigation of the loss of temperature by liquid steel during a teeming operation, a numerical technique was used to calculate the heat flows and the rate of temperature drop over the entire teeming operation. The calculations show that, before teeming, approximately 50 per cent of the heat loss is into the ladle wall at the level of the metal. As teeming progresses, the amount of heat lost by radiation to the wall above the metalline increases. The effect of variables, such as initial metal temperature, the preheat of the ladle and ladle cover, and delays, on the rate of temperature loss by the metal were determined.

Jan 11, 1973

The Grants register 1979-1981, edited by Roland Turner. London, MacMillan, 1980. (Available from Geonicla Publications, P.O. Box 31487, Braamfontein 2017 at R31,37; price to libraries R28,33.) Buyer's guide. Pretoria, South African Bureau of Standards, 1980. (Available free of charge from the Director General, SABS, Private Bag X191, Pretoria 0001.) SABS specification on gold alloys. World coal resources, by Bernardo F. Grossling. London, Financial Times, 1980. 160 pp. $D.S.155. Resources policy, a quarterly journal publish d in March, June, September, and December. Annua subscription: £40. Diamond jubilee 1980 The Associated Scientific and Technical Societies was established in 1920 primarily to 'promote the interests of Scientific, Professional and Technical Societies, the advancement of knowledge in Scientific and Technical subjects, and to uphold the professional status of such Societies,' and to 'represent corporately the views of Scientific, Professional and Technical Societies and the members thereof'. In this manner the strength of unity

Jan 1, 1980

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By R. T. White

The usual figures quoted for water usage in South African gold mines are 1 ton of water used per ton of rock broken, which represents a consumption of 4000 litres of water every second. Owing to the limited sources under ground water, the high cost of surface-water supplies, and the environmental problems of effluent disposal, water IS recycled continuously for underground use. This paper reviews the various types of water treatment and why water needs to be treated. The uses of lime and some flocculants are considered, since much of the mine service water requires only simple neutralization and clarification. Where mining depths necessitate the installation of underground refrigeration plant, more stringent water requirements must be met, and where plant performance is to be maintained, the prevention of system scaling and corrosion is necessary. The families of chemicals added to provide such protection are outlined, together with a description of the mechanisms of control.

Jan 1, 1985