Search Documents

By K. C. Corin, M. S. Manono

The mining and mineral concentration of Cu-Ni-PGM sulfide ores in South Africa occurs in semiarid regions. The scarcity and availability of water resources in these regions has become one of the biggest challenges facing mineral concentrators.S Owing to this challenge, concentrators have to find ways through which they can manage and control their water usage. Recycling and re-use of process water in mineral concentrators has therefore become common practice. This practice is beneficial in that it reduces reliance on municipal water, harnesses compliance to stringent environmental regulations on water usage, and it also offers a better response to the Sustainable Development Goals. This could however be somewhat concerning to the operator as recirculated water often has higher concentrations of ions compared to fresh or potable water. The unintended change in the process water quality may potentially affect critical aspects of flotation such as the stability of the froth. This has led to the need to find those process water ions that have the greatest impact on froth stability. Thus, this paper investigates the effect of various ions common in process water of a typical Cu-Ni-PGM concentrator on froth stability. Bubble size, water recoveries, foam height, and dynamic froth stability in both twophase and three-phase flotation systems are used as proxies for froth stability. Findings of this study are deemed crucial towards the development of a process water management protocol in sulfidic Cu-Ni- PGM ore concentrators. Keywords: Bubble diameter, electrolytes, flotation, froth stability, water quality

Jan 1, 2020

By E. P. Preis, R. C. W. Webber-Youngman

The real cost of any mining incident has, empirically, proven to be estimation-driven, rather than factdriven. One of the main reasons for this lies with the complexity of the cost composition of any given mining incident. Incident costs comprise both direct and indirect cost factors, and in many cases the costs associated with these factors are incurred during different time periods following the incident. In this paper we aim to identify the various cost factors arising from mining incidents, provide a thorough understanding of all the potential cost factors identified, and draw general conclusions on the knowledge obtained. Furthermore, recommendations are made on how mining companies could use the results, in order to assist them in calculating the costs of mining incidents. The paper also provides suggestions for further research, with the emphasis on the most significant immeasurable cost factors, namely the costs of implementing job accommodations following an incident, the harm to company reputation, and the decreased productivity due to low worker morale/psychological factors following an incident. If mining companies are aware of and understand which factors could contribute to the cost of any given incident, future planning and incident cost estimations could be easier. It should, however, be noted that although this study provides a comprehensive list of cost factors (and detailed explanations), other unknown cost factors relating to mine incidents could prevail in extreme cases.

Jan 1, 2021

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

1. Mining directory The mining directory, 1990. Mines and mining equipment companies worldwide. Don Nelson Publications Limited (P.O. Box 193, Barnet, Herts EN4 BLP, England).2. Mintek reports The following reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R25 (plus R3,25 GST) per copy to South African addressees, and US$25 per copy (including airmail postage) to addressees elsewhere. There is also an annual-subscription scheme for reports - R400 locally (plus R52 GST) and US$400 (including airmail postage) abroad. The subscription covers al the unrestricted reports published between 1st April and 31st March of successive years, which usualy amount to between 20 and 30. Report M392 Computer programs for optimization by the modified simplex method, by G.L. Moore. Sep. 1989. 25 pp. R25 + R3,25 GST in South Africa; US $25 elsewhere. Report M393 The preparation and certification of fourteen South African silicate rocks for use as reference materials, by E.J. Ring. Sep. 1989.21 pp. R25 + R3,25 GST in South Africa; US $25 elsewhere. Report M395 The separation of trace elements in high-purity rhodium and iridium materials, by R.V.D. Robet and S.M. Graham. Nov. 1989. 10 pp. R25 + R3,25 GST in South Africa; US $25 elsewhere. 3. Publications from Trans Tech The publications listed in this section are available at the prices given from Trans Tech Publications, P .0. Box 1254, D-3392 Clausthal-Zelerfeld, West Germany. Handling of bulk solids. Theory and practice, by P.A. Shamlou. 1988. 200 pp., US$ 59.50. Acoustic emission lmicroseismic activity in geologic structures and materials, by H.R. Hardy and F.W'. Leighton. Vol. I: 1977, 490 pp., US$45.00. Vol. 11: 1980, 500 pp., US$45.00. Vol. Il: 1983, 680pp., US$6O.00. Vol. IV: 1989, 720pp., US$ 75.00. Open pit mine design models. An introduction with FORTRANI77 programs, by E. Alaphia Wright. Early 1990, approx. 200pp., US$75.00. Bucket wheel excavator, by W. Durst and W. Vogt. 988, 450pp., US$118.00. Continuois-surjace mining, by T.S. Golosinski and F.G. Boehm (eds.). 1987, 720pp., US$128.00. Mining-science and technology. 1987, 1430pages, US$ 118.00. Practical handbook for underground rock mechanics, by T.R. Stacey and C.H. Page. 1986, 150pp., US$ 38.00. Professional users handbook for rock bolting, by B. Stilborg. 1986, 150pp., US$38.00. The lighting of underground mines, by D.A. Troter. 1982, 220pp., US$48.00. Elements of hydraulic coal mine design, by M.L. Jeremic. 1982, 16Opp., US$38.00. Continuum theory of rock mechanics, by Cs. Assonyi and R. Richter. 1979, 365 pp., US$ 58.00. Shear and bond in reinforced concrete, by G. Florin.1980, 86 pp., US$ 24.00. Theory and design of surface structures: slabs and plates, by G. Florin. 1980, 222 pp., US$ 24.00. Mineral processing laboratory manual, by A.-Z. Abouzeid. January 1990, approx. 200pp., US$48.00. Weighing and proportioning of bulk solids, by Hendrik Colijn. 2nd ed. 1983, 4OOpp., US$60.00. Solid-liquid flow. Slurry pipeline transportation, E.J. Wasp et al. 1977, 240pp. US$ 58.00. Optimum pipe size selection, by C.B. Nolte. 1978, 304 pp., US$ 60.00.Field instrumentation in geotechnical engineering, T.H. Hanna. 1985, 854pp., US$98.00. The 1990 yearbook and directory. Powder and bulk solids handling and processing. 1989/90, approx. 300 pp., US$ 124.00.

Jan 1, 1990

By R. Nyirenda, B. Besa, N. Dzimunya

The accurate estimation of peak particle velocity (PPV) is crucial during the design of bench blasting operations in open pit mines, since the vibrations caused by blasting can significantly affect the integrity of nearby buildings and other structures. Conventional models used to predict blast-induced vibrations are not capable of capturing nonlinear relationships between the different blasting-related parameters. Soft computing techniques, i.e., techniques that are founded on the principles of artificial intelligence, effectively model these complexities. In this paper, we use the random forest (RF) algorithm to develop a model to predict blast-induced ground vibrations from bench blasting using 48 data records. The model was trained and tested using WEKA datamining software. To build this model, a feature selection process using several combinations of Attribute Evaluators and Search Methods under the WEKA Select Attributes tab was performed. The correlation coefficient of the actual data and RF model-predicted data was 0.95, and the weighted average of the relative absolute error (RAE) was 10.9%. The RF model performance was also compared to the equivalent-path-based (EPB) equation on the testing data-set, and it was seen that the RF model can effectively be used to predict PPV. The study also demonstrates that the EPB equation is a suitable empirical method for predicting PPV.

Mar 30, 2023

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

By O. A. Bascur

Ores are becoming extremely variable with mineralogy and hardness disturbing the grinding and flotation circuits. The current grinding and flotation sensors provide large amounts of data for process optimisation. Adding the right context and operational events augments operational knowledge for proactive actions to improve the performance of the grinding and flotation circuits. A data-driven strategy is needed to enable operations, maintenance, and business personnel to quickly and easily take corrective action when abnormal conditions occur. A digital plant template transforms data into operational insights in real-time. It uncovers the hidden, idle and downtime losses. By measuring and managing these unproductive times, people find new ways of avoiding them, improving the profitability of the plant. The information created by the real time analytics enables the calculation of recovery in real time and develops predictive analytics models to find the best operating condition based on the type of ore currently mined. The creation of new workflows and collaboration between mining and concentrator plant and the enterprise, including services providers, are enabled. A grade recovery model is used to identify the best operating conditions in real-time. An optimal Gaudin size distribution shape is used to find the grinding operating conditions that optimise the metal recovery in the rougher sections of the mineral processing plant. Sensors in the flotation circuits enable estimation of metal recovery and determine the optimal froth depth and aeration profiles, using an industrial air holdup flotation model. The implementation of a recovery/grind strategy with industrial examples in non-ferrous metal concentrator is presented in the paper. Keywords: Digital transformation, soft sensors, predictive analytics, grinding flotation optimisation, flotation bubbles, particle size, particle size distribution shape, froth aeration profiles, flotation air hold up model, recovery predictive analytics

Jan 1, 2020

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

By C. Bester, G. M. Rohde

A major challenge in the mining sector is the responsible management and efficient storage of mine residue. Over recent years numerous tailings dams have experienced unintended spills and failures, with severe consequences for the mining industry, the environment, local communities, and the regional economy. The fourth industrial revolution (4IR) is impacting society due to increased interconnectivity, processing speed, and automated technologies. This paper explores whether 4IR technologies have the potential to mitigate risks associated with tailings dams. Experts in the field of tailings dam operational management were surveyed to determine their view on the risks associated with tailings dams and the potential of 4IR technologies to mitigate these risks. The survey found that a majority of experts believe that certain 4IR technologies have the potential to reduce the risks associated with tailings dam failures.

May 27, 2025

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

By G. B. Abaka-Wood, J. Addai-Mensah, W. Skinner

Recently, coal fly ash has become a potential candidate as a secondary resource of rare earth elements (REE). In this investigation, we studied the recovery of REE from fly ash from a commercial power plant. The specific aim was to assess the technical feasibility of recovering REE from the coal fly ash using conventional preconcentration methods, including gravity separation, magnetic separation, and froth flotation. The experimental results revealed that flotation achieved major gains in REE recovery and upgrading. However, during gravity and wet magnetic separation tests, the bulk of REE reported to the tailings. The results showed significant variations in the performance of the various beneficiation methods investigated. This study has confirmed that existing physical separation methods could be used to recover REE from coal fly ash prior to hydrometallurgical and pyrometallurgical processing, although some challenges persist.

Jan 2, 2022

Minerals Handbook 1994-95: Statistics and analyses et the world's minerals industry? by P. Crowsons, Basingstoke, Macmillan, 1994 ISBN 0 333 60931 X. £85. Available from Macmillan Direct Ltd., Houndmills, Basingstoke, Hants, RG21 2XS, UK. Review prepared by Theo J. Oosthuizen, Information and Educational Programmes Division, Mintek

Jan 1, 1995

Branch Minutes of the General Meeting held at President Steyn Gold Mine canteen on Wednesday, 10th May, 1978, at 4.00 p.m. Erratum We apologize to Mr J. G. Taylor for the error in one of his qualifications. Bio-engineering monograph The selection of papers presented at the International Bio-engineering Conference at the University of Cape Town organized by the South African Institution of Mechanical Engineers and held in April 1977, and which are appearing in The South African Mechanic al Engineer during April to June this year, will shortly be available in book form. Mathematics The Institute of Mathematics and Its Applications is planning the following conferences and symposia: The Nand F Proposals in Relation to Mathematics, 1st July, 1978: London School of Pharmacy. NIM reports Report no. 1917 The instrumental neutron-activation analysis of granites from the Bushveld Complex. (31st Mar., 1978.) Report no. 1951 Potentialities and limitations of four-parameter equations for the correlation of formation constants of metal-ion complexes in aqueous solution.(15th May, 1978.) Report no. 1963 An evaluation of the methods used at the National Institute for Metallurgy for the analysis of base-metal concentrates. (28th Apr., 1978.) Report no. 1964 The separation, by anion exchange, of noble metals on substituted cellulose. (28th Apr., 1978.) Guide To The Preparation Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal.

Jan 1, 1978

By C. R. S. Needes, M. J. Nicol, G. T. W. Ormrod, N. P. Finkelstein

The industrial application of a dioxide electrode uranium by C. R. S. NEEDES, Ph.D. (London) (Visitor), M. J. NICOL, Ph.D. (Rand) (Visitor), N. P. FINKELSTEIN M.Sc. (Rhodes), Ph.D. (Liverpool) (Fellow), and G. T. W. ORMROD (Visitor) A correlation between the potential of a U02 electrode and the rate of recovery of uranium has been proved in laboratory and plant trials. When the recovery rates change because of variation in the concentrations of Fe(III), Fe(II), SO4 'and H+, a positive correlation is observed. However, an 2- increase in the concentration of phosphate in solution produces an increase in the U02 electrode potential but a decrease in the rate of leaching of U02. The correlation between the U02 electrode potential and the rate of leaching of U02 is then negative. It is concluded that, as a control device, the electrode cannot compete with the platinum electrode for use on certain plants. Nevertheless, the U02 electrode will act as a useful warning device if the total concentration of iron in solution decreases to below a level concomitant with the economic recovery of uranium. Furthermore, because of the positive correlation between the U02 electrode potential and the phosphte concentration, the electrode will also be of value in the detection of an increase in the phosphate level in solution. When it was incorporated in a suitable industrial probe, the electrode was found to be able to withstand the rigours of the leaching conditions in a large pilot-plant pachuca, and only failed after six weeks' operation.

Jan 11, 1975

By J. H. C. Pretorius, P. Nelwamondo

"Although South Africa possesses more than 80% of the world’s platinum reserves, its reputation for reliability in supplying platinum to global markets is under threat. This is due to the 49% decrease in output per worker (1999–2014), while the domestic costs have risen by more than 10% annually for the past 5 years. In addition, the continued decline in the commodity price by 38.3% (2012–2016) has resulted in a significant portion of the sector producing at a loss in 2015. The Chamber of Mines (now the Minerals Councilof South Africa) has suggested that solutions to improve productivity and reduce cost pressures are required. This research aims to provide operational excellence through the application of event chain project management (ECPM) to improve productivity and reduce operational costs. A case study was used to carry out research in platinum mines, with data collected using a motion-time study to measure the current efficiency of operations in each mining stope through actual activity durations. The results indicate that through the application of the event chain project management methodology, risks affecting the mining stope schedule can be managed, the efficiency of operations was improved by reducing the time spent on each activity, productivity was increased by shortening the project duration, and operational costs were reduced in the process. IntroductionSouth Africa’s total mining industry production was 4.9% lower in 2016 than in 2015; it decreased by 1.9% year-on-year in December 2016, with the main contributor to this negative trend being the platinum group metals (PGMs) with a drop of 15.1% and contributing -3.8% percentage points (Statistics South Africa, 2016). Although South Africa possesses more than 80% of the world’s platinum reserves, the 8% drop in production output since 2008 has put the platinum mining industry under the threat of being seen as an unreliable supplier to global markets. This decline in production is caused by the 49% decrease in output per worker between 1999 and 2014. In addition, the continued decline in the commodity price by 38.3% from 2012 to 2016 and an increase in operational costs during the same period resulted in a significant portion of the sector producing at a loss in 2015. A turnaround strategy is required to overcome these challenges. The Chamber of Mines has suggested, among others, the need for solutions to improve productivity and reduce cost pressures. The implementation of these solutions will ensure that the PGM industry thrives and reaches its potential of growing production to more than 322 t by 2020 (Baxter, 2016)."

Jan 1, 2018

By H. Mulder, M. C. Bekker

The principal objective of this investigation was to conduct a thorough literature review on the status of project readiness mechanisms, tools, techniques, and frameworks for mining projects. The review aimed at identifying common readiness evaluation criteria as well as potential shortcomings that prevent the establishment of a generalizable project readiness index. The literature review included a general overview of capital project performances and the importance of project readiness assessments to improve project delivery success. The study then progressed towards literature involving mining projects and how this differs from infrastructure and industrial project assessments. The paper concludes by summarizing the current state of mining project readiness assessments, the unique and differentiating factors to be considered, and suggests recommendations towards the development of generalizable readiness assessment criteria for mining projects.

Sep 1, 2022

By P. W. J. Delport, E. Du Toit

Investing in a mining venture can be risky and stakeholders need transparent, unbiased reports to understand the Mineral Resources and Mineral Reserves a mining company holds. Readability and textual choice can be used consciously to manipulate perceptions, or it can be done unconsciously. This exploratory study investigates the readability and textual choice of supplementary Mineral Resources and Mineral Reserves Reports of companies listed on the Johannesburg Stock Exchange. The results indicate that narrative manipulation occurs in these reports through word choices that make the reports difficult to read, as well as specific narrative selections. This reduces the informational value of the reports. The results of the study will be useful to various stakeholders, such as mining company management, investors, investment specialists, financial analysts, and even employees and the general community, who all use these reports to make important decisions. It is also useful for the preparers of the Mineral Resources and Mineral Reserves Reports, Competent Persons, and other technical specialists to be aware of readability and that certain textual choices can affect the interpretation of these reports. It is recommended that bodies such as the JSE and the SAMREC and SAMVAL Code committees consider adding a plain language requirement to regulations, guidelines, and codes to ensure transparent, unbiased, and objective reports.

Mar 1, 2021

By N. T. Beukes

An engineering house?s perspective of required inputs in designing a copper electrowinning tank house and ancillary equipment calls for both understanding of the key fundamental controlling mechanisms and the practical requirements to optimize cost, schedule and product quality. For direct or post solvent extraction copper electrowinning design, key theoretical considerations include current density and efficiency, electrolyte ion concentrations, cell voltages and electrode over potentials, physical cell dimensions, cell flow rates and electrode face velocities, and electrolyte temperature. Practical considerations for optimal project goals are location of plant, layout of tank house and ancillary equipment, elevations, type of cell furniture, required cathode quality, number and type of cells, material of construction of cells, structure and interconnecting equipment, production cycles, anode and cathode material of construction and dimensions, cathode stripping philosophy, plating aids, acid mist management, piping layouts, standard electrical equipment sizes, electrolyte filtration, impurity concentrations, bus bar and rectifier/transformer design, electrical isolation protection, crane management, sampling and quality control management, staffing skills and client expectations. All of the above are required to produce an engineered product that can be designed easily, constructed quickly and operated with flexibility.

Jan 1, 2009

By D. Stone, M. Le Roux, Q. P. Campbell, M. Fofana

Float-and-sink analysis is widely used in the coal industry to obtain washability data, yielding important information about beneficiation potential and performance. This method is associated with health and environmental problems, and research into alternative densimetric methods is important. The RhoVol is a new technology developed by De Beers Group Technology South Africa (DebTech) for the image-based generation of densimetric data from ores. The analysis is done on a per-particle basis, within a size range of +3 mm –8 mm. In this paper we compare the established methods used for the float-and-sink analysis of coal with a new method using RhoVol. The aim of the study was to determine the validity of the information obtained from the RhoVol analyser by performing comparative densimetric analysis on three different coal samples. The results showed that the RhoVol method was more rapid, safe, and precise, but tended to consistently underestimate the density of the coal sample, probably due to varying coal porosity.

Oct 3, 2023