Search Documents

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By F. H. Cornet, D. Ask, O. Stephansson

We have conducted a stress analysis of overcoring stress measurements undertaken at the Zedex Test Site (ZTS) in the Äspö HRL, Sweden. Two different types of overcoring cells have been used at the site: the 9-gauge Borre Probe (CSIR-type) and the 12-gauge CSIRO HI cell. Inversion programs based on the least-squares criterion were developed and calibrated. The primary and secondary stress field in the ZTS were back-calculated using strain data from individual cells as well as from combining data from both cells. We propose that the combination of strain data from the two cells significantly improves the determination of the stress field. A striking result is the good agreement between the re-analysed overcoring data and the existing hydraulic fracturing data. The deviations for the horizontal stresses between the re-analyzed overcoring data and the existing hydraulic fracturing data are approximately 3 MPa. The deviation in the orientation of maximum horizontal stress is approximately 10-20°. Nous avons analysé les résultats de mesures de contrainte par surcarottage réalisées sur le site Zedex, du laboratoire souterrain HRL d’Aspö, en suède. Deux types de cellule de mesure ont été utilisés sur ce site : la cellule à 9 jauges (du type CSIR) et la cellule à 12 jauges (du type CSIRO HI). Un programme d’inversion mettant en œuvre une norme par moindres carrés a été développé et validé. Les champs de contrainte primaires et secondaires du site Zedex ont été évalués d’une part en considérant chaque mesure isolément, d’autre part en intégrant l’ensemble des données de déformation dans une inversion unique. Nos résultats suggèrent que l‘association des diverses mesures dans une intégration unique améliore nettement la détermination du champ de contrainte. Un résultat intéressant est le bon accord entre ces nouveaux résultats et les résultats des mesures par fracturation hydraulique. Les écarts sur l’amplitude des contraintes horizontales est de l’ordre de 3 Mpa, les écarts sur les orientations de l’ordre de 10-20°. Auf dem Zedex Test Gelände im Äspö Festgesteinslabor (HRL) wurde eine Spannungsanalyse mittels Overcoring Spannungsmessungen durchgeführt. Hierzu wurden zwei verschiedene Methoden verwendet: das 9-kanal Borre Gerät (CSIR- Ausführung) und die 12-Kanal CSIRO HI Zelle. Inversionsprogramme, die auf dem “least-squares”- Kriterium basieren, wurden entwickelt und kalibriert. Das primäre und sekundäre Spannungsfeld des Zedex Test Geländes wurde sowohl aus Verformungsdaten individueller Zellen als auch aus Kombination beider Zellen ermittelt. Wir nehmen an, daß die Kombination der Messergebnisse beider Geräte die Bestimmung des Spannungsfeldes signifikant verbessert. Überzeugender Beweis hierfür ist die gute Übereinstimmung der überprüften Overcoring Daten und Ergebnisse aus existierenden Hydraulic Fracturing Versuchen. Die Abweichungen der horizontalen Spannungen aus beiden Datensätzen ist etwa 3 MPa und Abweichungen der Orientierung der größten Horizontalspannung liegen bei etwa 10-20°.

Jan 1, 2003

By R. Peroni, J. Kopp

Mine planning and scheduling is based on using a geological model for the deposit. Blocks are used to discretize the deposit into mineable volumes where grade values are assigned. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for this task where an interpolated value is calculated within a discrete volume. This group of block grades is the input for sequence optimizers, which base their decision on the economical value of a given block. Ultimately, the economical value of a block depends on its grade, making mine sequencing sensitive to all estimated values. If one looks to a block not as a single grade but as a set of equally possible grades, its economical value will change as different grades can be assigned to it. Stochastic simulation is known to provide the tools to assess grade variability, which makes it possible to generate equally probable values in a block. Different grade block models can thus be built and multiple sequencing alternatives are observed by running the optimizer for these distinct inputs. The results demonstrate that the methodology is adequate for risk assessment and proves to be useful for mining project sensitivity analyses. Differences in the project net present value showed that there is little difference between the two simulation methodologies (sequential Gaussian simulation and sequential indicator simulation) applied. The process is demonstrated using a Brazilian kaolin deposit. Keywords: geostatistical simulation, mine planning, sequencing, risk assessment, open pit optimization.

Jan 1, 2003

By C. F. Vos, J. D. Miller, J. C. Davidtz

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate(DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromite rejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2006

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By Kurt R. P Petersen

This paper discusses the current approaches to modelling the DMS cyclone within the De Beers group. Current efforts are split into short term value-adding process understanding and longer term semi-fundamental analysis of separation mechanisms. To date, the basic applied approach has yielded significant value to the group, enabling operators to focus on simple diagnostic measures to control their process. The more involved modelling approach has given rise to a new understanding of the separation field, in particular that the high density gradients within a cyclone are highly localised, indicating that separation of medium to heavy density material takes place low in the cone. The model has proven to be conceptually robust, but still requires further development and validation to become a complete modelling and simulation tool for De Beers.

Jan 1, 2006

The November General Meeting of the Branch was held in the St. Helena Club at 8.00 p.m. on the 17th November, 1970. Mr J. N. Saunders (Chairman) was in the chair. There were also present six fellows, N. A. Honnet, C. J. Isaac, J. G. Kirchner, (Committee Members), J. M. Meyer, S. L. S. Swart and J. W. Wilson; seven members, D. V. Baum, M. de Lange, A. H. Edwards, G. J. G. Emere, E. R. Penny, G. P. Rundle, C. G. J. Vermeulen; six graduates, N. Mayer, H. Miller, E. J. Shillaber, P. J. H. Short, M. H. Smith, T. R. Stromsoe; five associates, M. Andriesse, A. E. Hooper, A. Paschalides, R. L. Solms, W. M. Todd; one student, J. C. Simms and 14 visitors. Apologies for absence were received from Messrs L. O. W. Leimer and G. Y. Nisbet. MINUTES OF THE ANNUAL GENERALMEETING The Minutes of the Annual General Meeting held on the 27th August, 1970, were taken as read. Their adoption, which was proposed by Mr N. A. Honnet and seconded by Mr J. G. Kirchner, was carried unanimously. MINUTES OF THE JULY GENERALMEETING The minutes of the General Meeting held on the 8th July, 1970, were taken as read. Their adoption, which was proposed by Mr C. J. Isaac and seconded by Mr J. G. Kirchner, was carried unanimously. GENERAL BUSINESS Members were advised that no more applications could be entertained for the visit to Western Holdings; they could, however, still apply to visit Welkom Mine and Harmony. TALK The Chairman invited Mr A. Paschalides to deliver his talk on 'Controlled blasting in stopes and new explosives developments'. The presentation proved to be of great interest to the meeting and lively discussion followed the talk. Mr N. A. Honnet proposed a vote of thanks to Mr Paschalides on behalf of all members of the O.F.S. Branch. CLOSURE The Chairman thanked Mr Paschalides for his talk and all present for their attendance, and as this was the last meeting for 1970 he wished all members a Merry Christmas and a Happy New Year. He declared the meeting closed at 9.30 p.m.

By U. Singh, E. T. Brown, J. Coxon

The rapid fracturing and deformation that occurs around excavations during rock bursts demand that support and reinforcement systems have both deformability and damping capabilities. The energy demand and supply approach currently used in design is considered to be too simplified to represent adequately the rock burst process and the support and reinforcement system requirements. Momentum change may be a necessary second criterion for the analysis of dynamic loading situations. At the St Ives Gold Mining Company, DE plates made from conveyor belt rubber, and dynamic cables with sliding anchors have been developed and used to improve the dynamic performance of support and reinforcement systems. La fracturation rapide et la déformation qui se produisent autour des excavations lors de coups de terrain demandent que les systèmes d’armature et de support soient déformables et aient une capacité d’amortissement. L’approche basée sur l’énergie actuellement utilisée pour la conception est considérée être trop simplificatrice pour représenter adéquatement les coups de terrain et les paramètres de conception des systèmes d’armature et de support requis. Le changement de quantité de mouvement pourrait être un second critère nécessaire pour l’analyse des cas de charge dynamnique. St Ives Gold Mining Company a développé et utilisé des plaques « DE » constituées de caoutchouc de courroie de convoyeur et des câbles dynamiques avec ancrage coulissant afin d’améliorer la performance dynamique des systèmes d’armature et de support. Die ploetzliche Rissbildung und Verformung, die sich in Baugruben waehrend eines Felseinbruchs ereignet, verlangt Stuetz- und Verstaerkungssysteme, welche verformbare und mildernde Eigenschaften aufweisen. Die derzeitlich gebraeuchliche Methode den Entwurf auf den Energiebedarf und dessen Abdeckung zu basieren, wird als eine unannehmbare Vereinfachung betrachtet, da sie den Felseinbruch und die benoetigten Unterstuetzungs– und Verstaerkungssysteme unzulaenglich darstellt. Die Aenderung der Umstaende kann einen zweiten Ansatz fuer die Analyse der Lastsituation erforderlich machen. Die St.Ives Gold Mining Company hat DE Platten aus Foerderband-Gummi und elastischen Kabeln mit verschiebbaren Verankerung entwickelt und dazu verwendet, die dynamische Kapazitaet der Unterstuetzungs- und Verstaerkungssysteme zu verbessern.

Jan 1, 2003

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By W. Dziurzynski, S. Nawrat, A. Krach

The paper presents research on the influence of the goaf methane inflow on a fire. The problem was investigated by a computer simulation of a fire developing in a goaf. A relevant mathematical model of the fire was selected, which considered both burning of coal and methane. The combustion process is very sensitive on the oxygen and methane concentrations, which was indicated on graphs of the fire temperature evolution. Examples of computer simulation for various location of the fire were considerd. Analysys of results confirms the influence of the content of the goaf methane on development of fires.

Jan 1, 2003

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By Baruch Grinbaum, Edwin Bwalya, Robert Minango, Deogratias Bukunkwe

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well known and established process. As the process advances, Cu is extracted to the solvent and is replaced by H+ in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: 1. SX-1: Standard extraction of Cu with oxime. The resulting raffinate contains about 6-8 g/L Cu and 50 g/L H2SO4. 2. SX-N: Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3 etc. The extraction removes no metals, but decreases the concentration of acid from 50 to 10 g/L. 3. SX-2: Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100-150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility in Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory scale, the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX-2 2-3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with Alamine based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 & SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E=2S for SX-2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By J. Cygankiewicz

Efficient prevention of mine fires is impossible without predicting the self heating processes in the given geological and mining conditions. The respective forecasting method is presented in this paper based on the following assumptions: - factor deciding on fire hazard in the underground workings is the process of heating of coal from the primary rock temperature to the critical temperature when the heating rate growth rapidly - another important factor is the fire incubation time defined as time needed to achieve the critical temperature. This time is determined by balance of heat and mass in the heated coal - contact of crushed coal with oxygen in air cause some exothermic processes as : physical and chemical sorption of oxygen , oxidation reaction and evaporation of humidity Heated coal transfers its thermal energy to the environment by conductivity to the rocks and by convection to the flowing gases. The heating is possible if thermal energy generated from coal is greater then the share transferred to the environment. The paper presents the laboratory method of measurement of heat generation in adiabatic conditions. Also the mathematical model with examples of computation enabling to forecast the self heating process of crushed coal is presented.

Jan 1, 2003

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located above the Arctic Circle in northern Sweden, is the second-largest underground mine in the world today. The orebody is a world-class high-grade magnetite deposit, from which three raw ore products are extracted. We use mixed integer programming to determine a production schedule, i.e., which production blocks to mine, and when to start mining them, so as to minimize deviation from planned production quantities while adhering to the operational constraints of the mine. The resulting model contains thousands of binary variables and a commensurate number of constraints, precluding us from obtaining a schedule in a reasonable amount of time. We describe a method that builds on prior, related work, to expedite solution time. Keywords: underground mining, production planning, optimization, integer programming

Jan 1, 2003

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

Visit to the Modderfontein factory of A. E. & C. I. Ltd 23rd November, 1972 A full programme was arranged to suit both the mining and metallurgical sections of the Institute. After refreshments were taken and visitors welcomed by the factory management we were split into two groups, viz metallurgical and mining. Book review Stress-relief Heat Treatment of Vanadium Steels by Or G. O. Joy and Or A. M. Sage (21 pp, 77 references).