Search Documents

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By E. D. Gardner

This bulletin, which discusses open-cut mining at the metal mines of the United States, is the last of a series of such papers by the Bureau of Mines describing the principal methods of mining.4 Open-cut mining is applicable to flat-lying mineral deposits relatively near the surface. Vein deposits seldom are amenable to this method, although outcrops of veins sometimes are worked as open pits. Most of the iron ore of the country is mined from open pits; according to the Minerals Yearbook, 67.4 percent was mined from open pits and 32.6 percent from underground mines in 1937. Open-cut mining is relatively new in the copper industry but yields more copper than any other method; in 1937 about 52 percent of the copper ore mined in the United States was taken from open pits. Lead-zinc ore has been produced from open pits in the Joplin (Mo.) district, but most of the deposits in this area, although flat-lying, are too deep to be mined economically by the open-cut method. In 1937 one company at Oronogo, Mo., was stripping overburden and mining mixed oxidized and sulfide ores by this method.

Jan 1, 1941

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By M. R. Geer

Information on the performance of coal-cleaning equipment is necessary to provide a basis for evaluating the performance of existing plants and projecting that of new plants. Performance data can contribute greatly to the wise selection and effective use of coal-washing equipment. The Bureau of Mines has published information on the performance of several commercial plants, as well as of some laboratory-scale equipment, 5 (2-9, 11, 12, 17-12, 21-25) from time to time for a number of years. A more intensive program to provide such information for all the principal types of cleaning equipment is underway. The present evaluation of table performance is part of this program.

Jan 1, 1962

By William F. Hahn

This report describes an illumination system suitable for use in a slope under construction, Simulator work was performed using actual lighting hardware to verify adequate light levels to meet MSHA proposed regulation (as published in the Federal Register, January 13, 1977). The sequence of operating activities for two different slope driving sites are discussed and lighting requirements are defined for each,

Jan 1, 1981

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Gary R. Peterson

In order to determine the potential availability of alumina to feed U.S. aluminum smellers, the Bureau of Mines evaluated 39 domestic mines and deposits of bauxite, alunite, and high-alumina clays and found that substantial increases in alumina prices would be necessary before nonbauxitic deposits could become competitive with bauxite. As part of the study, a price-tonnage relationship was developed indicating the quantity of alumina that could be produced from known deposits at various alumina prices and at a 15-pct discounted cash flow rate of return on the required capital investment. All capital and operating costs were calculated in August 1980 dollars. The domestic bauxite reserve base comprises three operating bauxite mines in Arkansas containing some 15.6 million metric tons of recoverable alumina (A1203). Ferruginous bauxites, clays, and alunites fall into the subeconomic category of identified aluminum resources, which, at the demonstrated level, contain over 4,000 million metric tons of alumina that are estimated to be recoverable. Analyses indicate that, at the demonstrated resource level, a total of some 15.6 million metric tons of alumina, all from three active Arkansas bauxite mines, is recoverable at a 1980 price of $0.12 per pound ($264 per metric ton) of alumina. A price of approximately $0.26 per pound ($573 per metric ton) of alumina would be required for production of the total U.S. resource. Thus, unless new technological breakthroughs occur that could make alternate sources of alumina competitive with bauxite, U.S. dependence upon imported bauxite will continue to increase.

Jan 1, 1981

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By Vance G. Leak

Leaching of manganese from low-grade Minnesota ores was studied over the temperature range 25° to 225° C at atmospheric and elevated pressures to demonstrate that good recoveries of manganese could be achieved from unroasted ores using reagents available nearby. Various combinations of ore, pyrite, lignite derivatives, and sulfuric acid were tested on a small scale. Pyrite alone required the highest temperature to effect a good extraction, but the combination of pyrite, lignite char, and sulfuric acid solubilized 99 percent of the manganese after 30 minutes of reaction at 75° C.

Jan 1, 1971

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981