Search Documents

By Clarke E. Schuetze

This project had as its objective the experimental investigation of water capsule production utilizing the Southwest Research Institute's submerged nozzle encapsulation apparatus (U.S. Patent 3,389,194). Initial efforts on this project involved nozzle configuration and shell formulation optimization. The shell formulation developed on a prior program was modified during the course of the project to obtain the best balance of capsule breakage resistance and water retention. Subsequent effort centered on determining operating conditions which would produce the best quality capsules for each candidate shell formulation as determined by laboratory tests. Some preliminary work was done to increase the production capacity of the encapsulation equipment. The program was extended with major emphasis concerned with scale-up studies of capsule production capacity and the treatment of problems associated with grouting cartridge fabrication. During the course of the program, water-containing capsules were produced which have good long-term water retention, block resistance and adequate strength. Using a single-nozzle design, a production capacity of 15.9kg (35 pounds) per hour was demonstrated to give acceptable capsules based on initial results.

Jan 1, 1978

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By Albert L. Toenges, Frank A. Jones

"INTRODUCTION The introduction of mechanized pining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and describes some systems of transportation utilizing rail haulage.ACKNOWLEDGMENTThe information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines wore studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies."

Jun 1, 1940

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By Arcy, D&apos Banister

The productive potential of the Nation's principal active and inactive silver mining districts has been evaluated, using 1964 economic conditions and assumed silver prices ranging up to $3 per ounce. On this basis, the United States has an estimated 5 billion ounces of unmined silver, excluding minor byproduct silver in gold deposits. Approximately 3.5 billion ounces are contained in deposits requiring higher silver prices to be economically minable, and about 1.3 billion ounces are in currently operating mines. An analysis of silver consumption trends since 1954 indicates that the free world industrial market will climb to nearly 800 million ounces annually by 1985. U.S. industrial silver consumption has been projected to increase at an annual rate of 4 percent from 1965 to 1985. Average annual increase for the remainder of the free world has been 8.1 percent since 1953; this is expected to level off with an estimated average increase of 5 percent to 1975 and 4 percent from 1976 to 1985. Foreign silver production has, in the past, exceeded consumption, but in 1960 the supply deficit was over 100 million ounces. U.S. production, also traditionally exceeding demand, was suddenly overtaken at the start of World War II. By 1964 the annual deficit, excluding coinage, was over 84 million ounces. World coinage requirements of silver are fast declining and expected to total only 25 million ounces annually by 1985. In fact, coins are already becoming major short-term source of silver to fill the large deficit between industrial demand and current production. The larger, long-term deficit (to 1985, the limit of this study) must be balanced by silver from the hoards and new production from silver deposits. Eventually all of the deficit must be met by new production or silver prices will rise until consumption is greatly curtailed. To balance free world supply and demand, it is estimated that the free world must produce an additional 85 million ounces by 1975 and 375 million ounces by 1985. The estimated proportion expected from U.S. deposits is 17 million ounces by 1975 and 74 million ounces by 1985.

Jan 1, 1969

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Robert T. Davis

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to the coal-mining industry's underground and open-pit mines that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1964

By Francis J. Kelly

This Bureau of Mines study was made to obtain and present facts concerning the production and marketing of rare-earth metals and thorium in the Central and Southern Rocky Mountains (Arizona, Colorado, New Mexico, Utah, and Wyoming, referred to in this report as the region) and to review the current demand for these elements in the United States. Little or no published information was available on the marketing practices for these commodities. As a result of many inquiries from industry, potential prospectors, and the general public, the various factors of resources, production (present and potential), marketing, and consumption have been investigated, and the results are set forth in this report. Material concerning occurrences and deposits is from published references detailed in the bibliography.

Jan 1, 1962

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

By R. A. Franks, J. C. Edwards, L. Yuan

To determine the critical air velocity for preventing smoke rollback, diesel-fuel fire experiments were conducted in the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory’s Safety Research Coal Mine. Such information is necessary for preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 to 300 kW depending on the fuel tray area. Airflow in the 2-m- (6.6-ft-) high, 2.9-m- (9.5-ft-) wide coal mine entry was regulated during the course of each experiment. The airflow was measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor and was recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light-obscuration monitors, ionization smoke sensors and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics fire dynamics simulator.

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By Ronald P. Hollenbeck

The value of mineral production in Alabama reached a new high of more than $246 million. 4 percent above the previous record established in 1964. New high values were reported for bentonite, portland cement, fire day, kaolin, miscellaneous clay, lime, crushed limestone, crushed marble, mica. salt, and sand and gravel. Among the States, Alabama ranked second in the production of bauxite and scrap mica and third in the production of native asphalt. The mineral industry of Alabama was dominated by the mining and processing of coal and Slone, the manufacturing of cement, and the production of crude petroleum, which together comprised 85 percent of the total value of mineral output, compared with 84 percent in 1964. The iron ore industry continued to decline. Coal production continued to increase, resulting in the State's coal-mining best year since 1948.

Jan 1, 1967

By J. E. Hipp

Three electrostatic field sensing proximity warning devices were tested using full-scale cranes and power line systems, a scaled model facility, environmental testing facilities, and theoretical/numerical analysis. The design objective of each device is to assist in safe crane operation near overhead power lines. Several design deficiencies (varying from device to device) were observed, including inadequate overlap in sensitivity ranges, utilization of vacuum tubes and electro-mechanical parts, temperature sensitivity and inaudible alarms. In addition, the testing showed major device limitations including sensitivity to boom orientations and length, polarization dependent responses, and unreliable operation in the presence of multiple power line circuits. The multiple power line circuit problem is intrinsic to electrostatic sensing devices. The remaining deficiencies and limitations are correctable within a state-of-the-art design. This investigation is not intended to evaluate the safety aspects or policy of utilizing proximity warning devices. Rather, the purpose is to determine the performance characteristics of such devices in relation to the criteria specified in proposed MSHA regulation 77.805-4 (i. e., the devices must alarm at a distance of 10 feet from the power line).

Jan 1, 1980

By L. V. Clark, Arthur La Motte

"INTRODUCTION The U. S. Bureau of Mines in 1930 and 1931 made a study of the properties and characteristics of liquid-oxygen explosives (L.O.X.) at the request of one of the largest users, in order to determine and eliminate the hazards attending its use.This report deals with the examination of absorbents for L.O.X. to (1) determine their most desirable and most undesirable characteristics, (2) to find ways and means of desensitizing absorbents to mechanical shock, and (3) to determine the effect that such desensitization of absorbents has on the explosive Characteristics of L.O.X.ABSORBENT MATERIALS The absorbent used in driving the Simplon Tunnel, the earliest project in which L.O.X. was used, was composed of crude petroleum, soot, and kieselguhr. During the World War, powdered cork, soot, sawdust, powdered straw, or other similar powdered materials were mentioned in the German military instructions for use of ""liquid air"" explosives. At that time the common types of absorbent, materials were compounded ones containing the above ingredients as well as kieselguhr, paraffin, gas oils, charcoal, bituminous coal, etc.Kuryla and Clevenger4 investigated absorbents of the above type and made the following statement concerning them:"

Apr 1, 1932

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By H. Tomlinson

"INTR0DUCTIONThis publication is a third of a series devoted to falls of roof and coal in coal mines of the Western States. It gives the results of examinations of the mines of the Rock Springs coal District of Sweetwater County, Wyo., which represent the principal coal beds therein and approximately 75 percent of total production of the State.A study was made of safety conditions at all the producing mines of the district and suggestions were offered the operators regarding methods and practices which would, in the opinion of the writer, provide additional safeguards to prevent accidents from falls of roof and coal.In presenting the subject, consideration must be given to such features as character of the coal beds, depth of cover. methods of mining, timbering practice, roof testing and supervision, and for comparative purposes to certain statistical matter bearing upon relation of accidents to their causes, tonnage produced, men employed, days worked, and lost days due to accidents during the 3—year period covered by this study.ACKNOWLEDGMENTSThe writer acknowledges the cooperation of the officials of the various coal companies, without whose assistance this work could not have been completed.F0UR REPRESENTATIVE COAL OPERATIONSThis report relates to four representative coal operations in the Rook Springs district of Sweetwater County, Wyo., which are referred to as mines A, B, C, and D. This group employs yearly an average of 993 men, representing 37 percent of the men in coal mines of the county, and has an average annual production of 1,484,373 tons, representing approximately 44 percent of the coal produced in the county. Figure 1 is a map of the Rook Springs coal district."

May 1, 1933

By George A. Morgan

Output of mineral products was estimated to be unchanged in 1983 from that of 1982 with the exception of petroleum. The country began production of crude oil from the Seme Oilfield, and all output was exported. Wd and charcoal constituted 72% of Benin's total energy consumption, and imported petroleum products and electric power accounted for the remainder. Cement was produced from imported clinker. The gross domestic product (GDP) was $1,061 million in 1982, the latest year for which information was available.2 COMMODITY REVIEW Gold.-Exploration was underway at Perma by the U.S.S.R. as part of the United Nations development program. Gold had been produced previously at Perma, where a grade of 0.289 troy ounce of gold per ton was reported, An exploitation program for the deposit was to employ about 100 people, and output was targeted to reach 1,600 troy ounces per year. Recoverable reserves were put at 96,000 troy ounces.

Jan 1, 1985

By L. D. Patts, J. D. Noll, S. E. Mischler, G. H. Schnakenberg

In this study, we evaluated the ambient diesel particulate matter (DPM) concentrations (at the intakes and exhausts of the mine) as the entire vehicle fleet of a stone mine switched from using 35% biodiesel to using a water emulsified fuel (PuriNOx). Elemental carbon (EC) was reduced by 45% when a PuriNOx blend containing 10% water replaced 35% biodiesel and by 57% when a PuriNOx blend containing 20% water was used. Other factors such as engine duty cycle and production changes could potentially cause some day-to-day EC fluctuations, and no direct comparison to commonly used dieselfuels (No. 1 or No. 2) was achieved. Therefore, a second study was performed in a controlled “isolatedzone” environment to fametal mine, comparing PuriNOxto No.1 diesel fuel in a load haul dump vehicle. The EC fraction of the DPM was reduced by about 71% when the PuriNOx blend containing 10% water was used and by about 85% when the PuriNOx blend containing 20% water was employed. This study did not determine how the water emulsified fuel would affect the engine or power.