Search Documents

By J. R. Thoenen

[Before 1914 Germany held a virtual monopoly on the world supply of potash for fertilizer purposes. During the World War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-tine prisms stimulated interest in various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany mad other sources reduced prices to below pre-war levels, and, as a result, most of the domestic procedures ceased operations. This experience demonstrated that a domestic source of potash was necessary but that it must be of such a nature that it could compete in price with foreign sources. As a direct result the potash content of thick]

Jan 1, 1941

By Roger M. Sherman

[Investigation of mine land characteristics, evaluation of irrigation systems, and evaluations by the mining industry, determined that irrigation is a feasible method for aiding revegetation of coal mined lands in western arid and semi-arid regions. The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid set irrigation. Irrigation should be supplemental by complimenting natural precipitation and be should implemented on a temporary basis.]

Jan 1, 1980

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By C. T. Baroch

CESIUM-137 ISOTOPE began to displace cobalt-60 III the treatment of cancer during 1956. Production and Consumption.-Consumption of cesium and rubidium was approximately the same as in 1955. Production, however, decreased, as several companies shipped from stocks produced in previous years. South Africa was the source of most cesium and rubidium minerals used in the United States in 1956. Cesium and rubidium metals and compounds were produced from ore by: DeRewal International Rare Metals Co., Philadelphia, Pa.; Fairmont Chemical Co., Inc., Newark, N. J.; Foote Mineral Co., Philadelphia, Pa.; and Rocky Mountain Research, Inc., Denver, Colo. Most sales were to domestic consumers, but small quantities were exported to Australia, England, Germany, and Sweden. New production facilities were under construction in. 1956 by San Antonio Chemicals to produce mixed potassium, rubidium, and cesium carbonates. A plant capable of separating and packaging 200,000 curies of cesium-137 annually was under construction at Oak Ridge National Laboratory.6

Jan 1, 1958

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. The IS countries that constitute the region accounted for 26% of world crude petroleum output, 17% of world natural gas plant liquid production, and almost S% of world dry natural gas production. About 66% of total world crude petroleum reserves and 31 % of total world natural gas reserves are in the Middle East. Transportation and port facilities in the region are geared to expediting efficient and rapid shipment of these materials. U.S.-dollar-denominated export sales of these fuels, estimated at $120 billion in 1989, provide funding for further diversification of the mineral industry. This is usually through development of downstream facilities for producing energy intensive metals such as aluminum and byproducts of the fuels such as petro-chemicals and fertilizers. Earnings from the industry are also channeled by sever-al Governments in the region to mineral industry projects in Africa and elsewhere. A fairly wide range of nonfuel minerals is produced in the region. However, the variety of minerals produced, output levels, and the size of the overall nonfuel mineral economy is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, ranked among the top three world producers of boron, chromite, pumice, and strontium. It was also a significant world producer of magnesium com-pounds, mercury, and sodium sulfate. Iran had generally lower output owing to 9 years of neglect to the mining sector between 1979 and 1988. It was a significant producer of gypsum and fifth in world production of strontium. Despite a very small domestic mineral industry, Israel was second in world production of bro-mine and a significant producer of phosphate rock and potash. Jordan ranked fifth in world production of phosphate rock. Iraq ranked about eighth in world production of sulfur, a commodity of major importance in the metallurgical, petrochemical, and fertilizer industries.

Jan 1, 1992

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By B. G. H. Thomas, W. P. Yant, A. C. Fieldner, R. R. Sayers, W. J. McConnell

"One of the outstanding problems confronting automotive engineers in attempting to construct motors of greater economy is that of eliminating the ""knock"" from the operation of the engine. Recent investigations of this detonation or knock in internal-combustion engines, especially of the high-compression type, have demonstrated that it can be eliminated or reduced by decreasing the reaction velocity of combustion by adding small quantities of certain compounds to the gasoline, This makes it possible to use engines of a higher compression ratio, thereby greatly increasing the mileage per gallon of gasoline consumed. The savings in fuel reserves from increasing the proportion of crude oil marketable as motor fuel and in permitting the designing of more efficient engines are obvious.Ethyl gasoline, one of the widely used anti-knock fuels, is ordinary motor gasoline to which has been added 3 c.c. of tetraethyl lead and 2 c.c. of a halogen carrier, as ethylene dibromide or trichiorethylene, or approximately 0.06 per cent of the lead compound and 0.04 per cent of ethylene dibromide by volume. Ethyl gasoline should not be confused with ethyl fluid, which is a mixture of concentrated tetraethyl lead and ethylene dibromide in the prowler proportions for mixing with gasoline, but is not a motor fuel and is not sold to the public. Also tetraethyl lead is not a motor fuel, and likewise is act sold to the public."

Dec 1, 1924

By R. V. Ramani

The overall objective of this study is to contribute to the reduction of the quartz dust hazard in underground coal mines through a better under-standing of the sources and generation of airborne quartz dust. This research project has included extensive experiments in operating mines for (1) documenting the amount of respirable dust generated, (2) measuring the quartz levels in host materials and airborne dust, (3) analyzing the size consist of the mined product, and (4) establishing the relationship between these various parameters. The results of the study indicate that the amount of dust airborne is a very small fraction of the total (<15 µm) and respirable (<7 µm) dust generated. The quartz contents in the total and respirable airborne dust are generally higher than those in the host material. Quartz content increases with decreasing size of airborne dust. Also, it appears that rock breaks into a different size distribution than coal. The source of quartz for the airborne dust appears to be the roof and the floor material rather than the coal seam itself. No general relationship is found between the Hardgrove Grindability Index and either the quartz content in the airborne dust or the amount of respirable dust. Extended descriptions of the experimental design, the experiments, data analyses and results are presented in this volume. The raw data, the data management computer program and the sampling and safety plan are presented in Volume 2.

Jan 1, 1987

By Clark P. Mangelsdorf

The report consists of two parts. In Part I is a state-of the-act study of roof truss technology as of January 1979. Included are a history of the truss concept, a review of analysis techniques, a record of hardware available and equipment used in its installation and numerous examples of user experience. Part II is concerned with a study of the role of friction in the behavior of a roof truss. The appendices include laboratory tests by the author.

Jan 1, 1979

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By Yi-Shen Li

This report has been prepared by Lockheed Missiles & Space Company, Inc. (LMSC), under United States Bureau of Mines Contract No. H0220040 dated 21 June 1972 for the design, development, fabrication, and certification of the One-Hour Self-Rescue Breathing Apparatus (PBA). The PBA is a self-contained, oxygen-generating, CO2-removing closed-loop breathing apparatus that provides a minimum of 1 hour of breathable atmosphere during escape from a mine with a contaminated or oxygen-deficient atmosphere. This Cost-Plus-Fixed-Fee (CPFF) contract has been successfully completed in a three-phase program. The Phase I tasks included the design, development, and fabrication of prototype units developed at LMSC in accordance with the requirement of the Code of Federal Regulations (CFR) Title 30, Chapter 1, Subchapter B, Part 11 (Appendix A), and was submitted to the National Institute for Occupational Safety and Health (NIOSH) for joint NIOSH and Bureau of Mines certification testing.

Jan 1, 1974

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

By John J. Mulligan

The Bureau of Mines investigated coal deposits at Mount Gran (latitude 76°59&apos; S, longitude 161°07&apos; E), Victoria Land, Antarctica, during the austral summer of 1959-60 as part of the continuing U.S. Antarctic Research Program, which is under the auspices of the National Science Foundation. The coals and associated rocks were measured, sampled, and analyzed. Five coalbeds, ranging in thickness from over 10 feet to scattered fragments of coaly material in sandstone, occur in a sandstone-coal series overlying a series of crossbedded red-buff sandstones. Both series are part of the Beacon group of sediments, and both show some evidence of pressure metamorphism. The sandstones are poorly cemented and are composed dominantly of rounded and often frosted quartz grains. The sediments have been broken and uplifted by a series of massive diabase sills. The broken nature of the sediments precluded an estimate of the amount of coal present. The Mount Gran coals are highly attrital banded anthracites and semianthracites that have most commonly a moderately dull luster but do include bright bands. Coal in contact with or near diabase intrusives is partly graphitic but shows no evidence of coking. Apparently the coal was beyond coking rank before emplacement of the adjacent intrusives. Fragments of the plant Glossopteris indica found with the coal suggest Permian age but do not prove it. The coals appear to be derived from plant remains that collected in shallow basins; individual coalbeds would tend to be lenticular bodies that formed in different places as the dominantly sandy sediments were deposited. The wide distribution of coal indicates that coal-forming conditions prevailed over much of the continent; the great thickness of Beacon sediments indicates that similar conditions may have persisted through a long period of geologic time. Generally similar coal deposits may occupy widely separated stratigraphic positions.

Jan 1, 1963

By Franklin H. Persse

The Bureau of Mines estimated reclamation costs for 13 surface coal mines in nine States west of the Missisisppi River. With the exception of the Pacific Coast coal province, at least one mine in each of the western coal provinces was studied. Cost estimates were, made using standard estimating procedures from data obtained from company records, interviews with industry personnel, and onsite observations. Estimated costs are presented in four categories which represent the four phases of mined-land reclamation: (1) Design, engineering, and overhead; (2) bond and permit fees; (3) backfilling and grading; and (4) revegetation. Estimated costs as of the first quarter of 1976 are expressed as averages and ranges in terms of per acre, per ton of coal produced, and per million Btu. Total reclamation costs ranged from $860 to $7,200 per acre, from 6 to 84 cents per ton, and from 4 to 35.3 mills per million Btu. A mine in the Northern Great Plains coal province (Region D) showed the highest per acre cost whereas mines in part of the western region of the Interior coal province (Region A) experienced the greatest per ton and per million Btu cost. The high cost of reclamation in the Western United States is reflected in the backfill in and grading category, particularly in the cost of topsoil removal and subsequent replacement as required by individual State reclamation regulations.

Jan 1, 1977

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962