Search Documents

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

By T. G. Donnelly

This final report summarizes the prototype development and testing of an air curtain respirotory protective device under Bureau of Mines Contract HO122087. The air curtain respiratory protective device, as part of a miner?s hat, provides protection for the underground mining machine operator against inhalation of dangerous amounts of respirable coal dust. Major components of the air curtain respiratory protective device are: 1) a modified miner hat incorporating an air curtain jet manifold from which the protective air curtain emanates, 2) a motor blower which supplies the air for the air curtain, 3) a filter element to remove the particulate material from the air used for the air curtain, and 4) the hoses and coupling used to duct the filtered air from the motor blower to the modified miner's hat.

Jan 1, 1973

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

By Shih-Chi Chang

[An exploratory research is done on untreated coal 1v- using&apos; x-ray crnctinn techniques. Comparison is made on diffraction data before And pct Pr n-tiAne is pressurized (n the coal samples. Although, only ? qualificative -1; t s obtained, the FoIIowing Statement r :&apos; n untreated teal seem- There are other materials in cost. They are accumilated in !e ,r rc r, cin? the microseoric layered structure of coal. 7"P partial graph r :r a&apos; o., «&apos; the i&apos;pr1 cart o ! in cna1 assumes varclor, r,rie&apos;,r: r in&apos;is. R nr ?-&apos;c,.r1&apos;ed I n coal is helm ;n the micrornre s&apos;??ste^ o&apos; c, .:l an&apos; t rr i, ,o <.~i:&apos;epee of Ion(4inc to carton h« x-ray tit If raction me.:SUr&apos;rientq. :t?e me r &apos; nP in r^icropores assumes no structure themselves at room tempera¬FLre. ;inally, some of the other materials in coal are in the form of }vrlrited crystallites and they have anisotropic pro&apos;th hnt&apos;1? in the lavers.]

Jan 1, 2012

Objective To develop safety training tools for mine safety and health professionals that fill gaps in currently available materials. Background Over the past 4 years, NIOSH has developed and released a series of training videos targeted at underground mine safety. These videos were developed in close cooperation with the mining industry and safety training professionals and were intended to provide realistic, interesting, effective training to both new hires and experienced miners. The videos cover the mining cycle, starting with the breaking of the rock (Handling Explosives in Modern Mines), making certain the work area is safe after a blast (Rock Falls— Preventing Rock Fall Injuries in Underground Mines), installation of ground supports and recognition of failed supports (Miner Mike Saves the Day), and hauling both ore and materials in the mine (Hazards in Motion). A separate video (Hidden Scars) captures the story of a fatal rock burst through an interview with a miner who nearly died and who lost his partner in the accident. These videos have been extremely popular in the mining industry and are being used across the nation as well as in 18 other countries. Two of them, Rock Falls and Miner Mike Saves the Day, have won Alice Hamilton awards, NIOSH’s highest recognition for Excellence in Occupational Safety and Health, in the Educational Materials category. Approach A recently completed independent evaluation of the SRL mining videos identified five themes that mine safety trainers consider necessary for successful training materials: high quality, credibility, accurate content, effectiveness, and an engaging nature. All of the NIOSH videos were rated very high for each theme. Using these measures of effectiveness, a more difficult challenge has been undertaken. Much has been written in the mining industry about the coming turnover in employment. The average age of miners in the United States is approaching 50, and many of the “experts” will be leaving the industry as they reach retirement age. The mining industry, like many industries involving skilled labor, relies heavily on a master-apprentice relationship between new hires and older miners. New hands learn from experienced miners. Their learning falls into three primary categories—they learn what’s important to know, they learn how to do things correctly and safely, and they learn the culture.

Mar 1, 2002

By Alan A. Campoli

OD March 20, 1989, a meeting was held at the U.S. Bureau of Mines Pittsburgh Research Center at the request of Senator Pete V. Domenici of New Mexico. The purpose of the meeting was to engender a technical relationship between the National Laboratories and the minerals industry. During the meeting, the Director of the Bureau of Mines, T S Ary, suggested that since the Bureau is the focal point for mining research in the United States, it would be appropriate for the agency to act as the liaison between the National Laboratories and the minerals industry. As the first step in this process, the author was selected to perform a 6-month investigation to better define the proper role of the Bureau in this area. As part of the investigation, the mining and mineral-related technology available at 21 major U.S. Department of Energy (DOE) Research Laboratories was reviewed. It was assumed that the broad range of scientific and technical areas covered DOE research would provide fertile ground for mining-related technologies. It was hoped that the applicability of DOE research to this liaison effort would be indicative of Federal laboratories in general.

Jan 1, 2011

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada&apos;s output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By C. P. Haller, S. J. Aresco

"INTRODUCTION The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heat¬ing value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions./ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made.Analyses of the delivered coal and ""tipple"" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.The Government purchased approximately 5-1/2 million tons of coal in fiscal year 1951. In connection with these purchases, the Bureau analyzed 10,700 samples. These are published for the use of Government officials and the public. A series of publications s been completed on coal analyses by States, or, where production is small in any State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications contain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals.The technical papers published by States, with their numbers are: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement, 645); Pennsylvania Anthracitic, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supple¬ment, 618); West Virginia, 405 and 626; and Wyoming, 484."

Feb 1, 1953

By Arthur V. Petty

In Bureau of Mines research on recycling chrome-containing refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated. By means of dry magnetic separation on minus 6-mesh crushed wastes, a concentrate was produced. After minor adjustments to the particle size distribution, full-size refractory brick were dry-pressed by a commercial producer and fired to 1,450° and 1,730° C. Standard testing procedures were used to determine the cold-crushing strength, modulus of rupture at 25°, 1,300°, and 1,500° C, hot load, thermal shock resistance, thermal expansion, and slag resistance. Optical and electron microscopy were used to determine grain-bonding mechanisms, and energy-dispersive analysis of X-rays was used to determine elemental distribution. The test results indicate that the beneficiated material could be used to produce a refractory product suitable for moderate-temperature applications.

Jan 1, 1982

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted