Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications sys tem which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a relatively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurement s of ambient surf ace electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal- to-noise ratio at the surf ace. Numerous C .W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surf ace magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null is the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken Into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

Jan 1, 1974

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By Dick T. Atkinson

This report describes the Foster-Miller program that designed, developed, built and tested an automatic, remote control mine car coupler. This new coupler gives the motorman the capability to selectively couple and uncouple cars from the locomotive, to transmit braking intelligence to the coupled car s and to determine if the trip is intact. Hazards due to derailment and runaway cars will be reduced as the brakes are automatically applied in any uncoupled car. Laboratory tests described herein have been completed on the coupler set. Applications include, but are not limited to, the unit train system.

Jan 1, 1976

By Thys B. Johnson

The mine system analysis and evaluation study presented in this report was part of the U. S. Bureau of Nines' Tertiary channel project conducted under the Heavy Metals program. The Badger Hill pit, located on the west end of the San Juan Ridge area, near Nevada City, California, was the site of the Bureau's field work. The objectives of this study were: (1) Determine potential alternative mining systems for some of the large tertiary channel gold-bearing gravel deposits, and (2) Identify areas of technology where further investigation would be merited because of their potential inclusion in a mining system for such deposits, The study involved the development of a mineralized block inventory, an economic block inventory, determination of optimum ultimate mining limits and a preliminary economic mining system evaluation. Computer programs were developed and utilized for each of the study phases stated above. The sampling program conducted at Badger Hill by the Bureau Delineation Group together with confidential drill hole data provided by the San Juan Gold Co. formed the basic gold values and distribution information from which a deposit model was developed. The deposit was divided into minable block units and net economic values were assigned to each block for various configurations of both open-pit and underground mining methods based on cost and performance data provided by the various Bureau of Mines Research Centers. A number of controllable variables such as: (1) Mining method (open-pit and underground), (2) depth of mining cut, (3) production rate and (4) equipment type and capacity were evaluated. The prime measures of effectiveness on which the mining systems where judged were discounted cash flow rate of return and maximum utilization of natural resources. The analysis showed that underground mining of the Six-Mile Tertiary channel gold-bearing gravel deposit under consideration was uneconomical and did not permit maximum recovery of the resources within the channel. It was also apparent that mining the Six-Mile Deposit for gold alone is uneconomical or at best marginal at a gold price less than $80 per ounce. The analysis showed that the potential for an economic mining operation within the Six-Mile Deposit exists when the gravel resources of the channel are considered together with the gold. It was determined that the highest rate of return would be realized with a 20-year open-pit mining operation yielding 745,000 ounces of -gold and 55 million cubic yards of usable gravel.

Jan 1, 2012

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. Then enough circulars have been completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed by bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual mines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); ventilation; wage, contract end bonus systems, etc.

Jan 1, 1930

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

By E. H. Burroughs

This bulletin is the fifth in the series of petroleum bibliographies publis:\:l.ed by the Bure.au of Mines, Bulletins 149, 165, 180, and 189 being compilations for the years 1915, 1916, 1917, and 1918, respectively. In this bulletin the same general plan has been followed in arranging the references, but a few changes and additions have been made in the classification.

Jan 1, 1923

By Bryan R. Carmenati

This report documents the need for formal health and safety, and equipment operations training in the mine construction industry. The outlines, objectives, and training texts were developed based on the recommendation of needs of mine construction personnel, and those of Dames and Moore (Safety Analysis of Shaft Sinking operations, 1977) and Kinton, Inc. (A Training Program for Conventional and Raise Drill Construction Personnel; Phase I, 1979). The training material samples contained herein (and under separate cover in its entirety) are designed to improve the safety and production of those in mine construction. An instructor-directed presentation is recommended. The results of the study are presented in the Findings and Recommendations section of this report.

Jan 1, 1982

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user's manual, including a program listing, is presented in the appendices.

Jan 1, 1974

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

This report is a compilation of all information obtained in accordance with the requirements of contracts SO122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies : Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gau-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated Mine visits and in-depth interviews were made alt the following sites: Robena No. 4, Pennsylvania Greenwich Colliery Mines, Pennsylvania Somerset Coal Mine, Colorado Keystone No. 1, West Virginia Harris Mine No. 1, West Virginia Baldwin Underground No. 1 Mine, Illinois Lovilia No. 4 Coal Mine, Iowa Orient No. 3 Coal Mine, Illinois

Nov 15, 1974