Search Documents

By B Mohanty, R Deshaies

Initiation of small diameter explosives by sympathetic shock pressure in water has been investigated under controlled laboratory conditions. Changes either in the geometry of the donor explosive or its point of initiation can alter the essential characteristics (amplitude and duration) of the resulting shock pressure pulse. The pressure signatures from both spherical and cylindrical explosives donors have been studied, in water as well as in various explosive matrices. This paper summarizes the investigations carried out with both 'primed' and 'non-primed' slurry and emulsion explosive matrices with various types of voids. These measurements serve the basis for predicting distances in water for sympathetic initiation for both spherical and linear charges. It is shown that the explosive-detonator system in combination has a far greater probability of initiation due to sympathetic shock pressure than either the explosive or the detonator alone. Various explosive matrices with air bubbles and glass microballoons have been examined and the differing sensitivities to shock pressure explained on the basis of these measurements. It is also concluded that explosives containing air bubbles instead of microballoons would be significantly more prone to sympathetic initiation.

Jan 1, 1992

By Michael S. Wieland

Delay detonators that are damaged by cross-hole wave interactions degrade blasting work and raise the risk of incidents. Damaged detonators impose risk, because they can retain sensitive explosives that respond to stray energy during recovery, inspection or disposal. Laboratory techniques were developed to rank the ruggedness of delay detonators under replicated field-shooting conditions. The hazards are tremendously magnified if trial detonators are installed directly in secondary explosives to rank initiation strength. Therefore indirect ranking techniques were sought that mitigate the risks without compromising the worthiness of the method. Four types of hardware fixtures, referred to as simulators, were developed to yield distinct forms of transient compression. The shock and rift versions generate compression pulses representative of in situ waveform components. The waiting time, until the trial detonator functions, duplicates typical delay periods. The trial detonator is mounted within water, which has a density and inertial resistance comparable to most blasting explosives. The work output from the trial detonator explosion is registered as fixture wall-expansion. This work output determines malfunction results, regardless of which type of simulator is used.

Jan 1, 1997

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

By Michael S. Wieland, Thomas C. Ruhe

Delay blasting in underground coal results in shock waves traveling through the coal that can damage delay charges remaining in the blast pattern. Undetonated explosives which are dynamically desensitized or react sympathetically from shock wave impact ruin blast results. Such malfunctions, sometimes manifest as misfires, more frequently are covert weak detonations, and result in poor coal breakage and fumes with above normal toxicity. To reduce these mining hazards and resolve charge performance problems, the Bureau of Mines has developed and tested forty prototype rugged explosives in the laboratory. Rugged explosives work properly under difficult circumstances because they not only retain their shock initiation sensitivity but also are resistant to shock damage. This research investigation resulted in one candidate emulsion explosive, formulation #37, which passed all the permissibility tests required by MSHA approval regulations. However, approval was not granted because it reached shelf-life (would not shoot properly) seven months into testing. For research purposes, the remaining tests were conducted with a second batch of formulation #37. This paper discusses the prototype rugged explosive composition and permissibility test results. Where possible, for reference purposes, comparisons are made to a commercial product that has been approved. Further research work is required to overcome the noted deficiency of short shelf-life.

Jan 1, 1992

By Daniel Haines, Benjamin Konshak, Michelle Crull

American Technologies Incorporated Group (ATI) is the prime contractor with U.S. Army Corps of Engineers, Huntsville Center (CEHNC) in the Honolulu District for the removal of munitions and explosives of concern (MEC) at the Former Waikoloa Maneuver Area. The site is approximately 123,000 acres on the Big Island of Hawaii, which was used as an artillery firing range with live ammunition and other explosives deployed. ATI utilizes state of the art metal detection equipment to find and excavate metallic anomalies that have hazard potential. Both the investigation and disposal procedures present challenges due to residential communities and archeological sites that are located in and around the site. In order to excavate metallic anomalies safely and without adverse impact, ATI utilizes CEHNC-designed, open front barricades constructed of sandwiched sheets of aluminum with a support structure. When munitions or explosives are located, ATI is responsible for safe disposal using shape charge perforators to detonate the item where found. Sandbags are used for mitigating the effects of all detonations.

Jan 1, 2008

By Thomas E. Ricketts

Limited void volume blasting (LVVB) occurs when rock is blasted into a volume that is not sufficient to let the rock expand to its free-bulking value. The freebulking value is obtained when the rock particles have enough space to separate, tumble and rotate to produce the maximum amount of void possible between the fragments when they finally come to rest. Although bulking value depends on particle size distribution and shape, a typical free-bulking value for uniform, finely broken shale is about 1.67. LVVB occurs in almost every type of blasting used in both surface and underground mining operations. For example, in multiple-row bench blasting for surface mining, the final delays that are designed to fragment the rock furthest from the free-face are generally confined by previously blasted rock which results in a LVVB situation. In underground mining, the blasting is automatically confined and is commonly done intentionally to limited void volume to reduce mining cost and improve safety. LVVB primarily affects rubble bulking and thus the excavation of the broken rock which is related to the productivity and economics of a mining operation.

Jan 1, 1989

By Janice Reed

The first seismograph was developed around 132 AD. Much has happened since then. The “modern” seismograph (> 1920) has seen a lot of changes. From falling pin seismographs to magnetic tape units to today’s Z-curve analysis models, the blasting seismograph remains a necessary and useful tool to the blasting community. But why so many changes? What forces drive the advancement of the seismograph? There are many answers and aspects to this question. Research, regulation, and technological advances are the primary forces behind innovation in our industry. But these three forces also drive each other. Research drove our industry from displacement seismographs to particle velocity seismographs. Technology took us from 80 pound seismographs to units weighing less than 5 pounds. Regulation (and litigation) - the driving forces behind the Z-curve analysis units. How have these innovations helped today’s blaster? Have there been any negatives? It is important for today’s blaster to understand how we got here and why.

Jan 1, 2005

By Qi Jinduo, Gong Min

On the basis of actual parameter of wall control blast in Nanfeng mine, China, the process of dynamic stress changing between two column charges was studied recently for a presplit-cushion blast by holographic photoelasticity. In the experimental model, two holes were simultaneously detonated from both ends (four ignition points). The bottom of the holes were loaded more than other parts (heavy charge). Under these conditions, four consecutive isochromatic fringe patterns at different times were acquired in one loading run, and the characteristics of the stress distributions were compared at different places and times in the holes. It was found that interaction types of stress waves vary along the holes. The theory is posed that the stress wave which is formed by the interaction of earlier producing P wave and later S wave along a distributed line charge is the most important part in all stress waves. Research indicates that a heavy charge in the bottom of the holes is crucial to producing a presplit-cushion effect at the bottom. "End Effect" doesn't affect the magnitude of stress along linking lines between the bottoms. The chief fields of the "End Effect" are also explained in the paper.

Jan 1, 1998

By P D. Katsabanis, L Liu

Numerical modelling of fragmentation and throw is used to provide information on practical blast design parameters. The function of airdecking and its practical implications, the importance of the initiation point and aspect ratio of cratering charges and the timing between adjacent blastholes are investigated. Accuracy requirements for detonators are discussed with emphasis placed on the volume and fragmentation of the blasted rock, and compared to experimental results. Practical guidelines which have been based on intuition are examined using the model. Some of the predictions have been tested and correlate well with experimental results, obtained in the laboratory. Findings show that a minimum airdeck length is needed to realize any benefit from the application of airdecking in production blasting while the process can enhance the shock energy provided by non-ideal explosives significantly, bottom initiation of charges is beneficial to fragmentation and the aspect ratio for cratering charges can exceed the traditionally accepted ratio of 6. Regarding timing, in the ease of cratering charges, true simultaneous initiation shows beneficial results for the volume of blasted rock; however the accuracy required for practical detonators is very high. Fragmentation improves after a certain delay time while the optimum can be achieved at a range of delays. Timing affects muckpile shape; however it appears that subtle differences in delay times do not have a significant effect.

Jan 1, 1997

By Gordon M. Matheson, David K. Miller

Sinkhole development in karst terrains is a serious problem and risk to facilities built in these areas. The potential for sinkholes are a function of many things including the chemistry of the underlying rock, the location of water conductive fractures and fissures in the rock, the natural fluctuation of the ground water table, vibrations from various sources and surface regrading activities. When sinkhole open near quarry operations the occurrence of these features is occasionally attributed to vibrations from quarry blasting. The purpose of this paper is to review the evidence regarding the development of sinkholes as a result of quarry blasting. In general, it has been found that sinkholes result from collapse or piping of overburden soils into cavities or caverns developed within underlying carbonate rocks that have been in existence for many thousands of years. The overburden soils in karst areas are typically clayey and as a result are not subject to densification or liquefaction as a result of vibrations. The primary cause of an increased rate of sinkhole development can be attributed to changes in the ground water table or local surface water drainage. These changes may be caused by seasonal fluctuations, ground water level lowering in drought periods, dewatering of excavations or quarries, or local changes in surface drainage resulting from grading activities.

Jan 1, 1998

By Michael S. Wieland

Toxic fume concentrations from industrial mining explosives depend somewhat upon the type of rock (or other strata) confinement. Though traditional detonation theory disregards this influence, the work principal from thermodynamics reveals it, when the violent interactions that transpire within the rock blast are taken into proper account. Resolution of the work principle technique requires total thermodynamic equilibrium under constraint, so the nonequilibrium dynamics is rendered in that way, using an old trick from theoretical mechanics that revises the representation of forces. The rock pressure reduces to a four-component sum: the rock compressive strength and natural atmospheric pressure, as reckoned quasi-statically, and the gravitational influence and reversed inertial resistance, as reckoned dynamically. Tabulated specie concentrations and graphical trends reveal the dependency upon rock pressure, rock temperature and the fuel-oil percentage in ammonium nitrate mixtures (ANFO), used to illustrate the model. Rigid-wall test chambers have notable ullage (residual space), where rapid expansion influences the reaction quenching, yielding a fume spectrum unlike that for rock confinement; reported rock tests are therefore used for comparisons. For the thermodynamic regime where quenching occurs, seven concentrations are resolved, including carbon monoxide (CO) and total nitrogen oxides (NOX). Their trends yield inferences regarding the way unwanted charge desensitization from transitory hole-to-hole wave impact in conjunction with reduced rock pressure can yield nasty toxic fumes, the dark rusty cloud phenomenon!

Jan 1, 2005

By Claude Cunningham, Szendrei

The partitioning of blasting energy into “Shock” and “Heave” components is a popular concept for attempting to match explosives to particular ground conditions and blasting results. The issue is complex, as it affects both the detonation process and the immediate response of the rock skin. However, the fundamental process of energy transfer from the explosive to the rock through the blasthole wall is not well defined. Clues to the “Shock” phase of blasthole expansion are given by cratering behaviour of materials subject to high velocity penetrators. The final cavity volume defines both the energy used to achieve this and the resistance of the confining material. Attention is being given to the link between penetration of a solid target and expansion of a readymade hole, both producing the same outcome. The benefit of this work is that it leads to clearer understanding of how explosives will impact upon the blasting results and helps to explain the energy consumption in blasting.

Jan 1, 2004

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Jan 1, 2005

By Paul Sairato, Cathrine E. Johnson

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. This paper provides the data from a second, restructured, online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2015

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By Joshua Hoffman, Catherine Johnson, Braden Lusk

Blasting conducted in surface coal mining operations in the Appalachian region consumes a significant amount of blasting agents. Emission of oxides of nitrogen (NOx) from these operations potentially represents an environmental challenge. This paper presents work conducted to quantify NOx output from the detonation of blasting agents common to surface blasting operations in surface coal mines. Annual ANFO and emulsion consumption data was collected from an operational surface coal mine located in West Virginia. It is known that many factors contribute to the types of gaseous byproducts released from the detonation of explosives. These factors include but are not limited to: fuel to oxygenator ratio, degree of confinement, and contamination. While, past research has been conducted to study the relationships these factors play on the release of NOx, these findings do not agree with one another. The annual explosive consumption values from the West Virginian mine were applied to NOx emission conversion factors in published literature. This lead to a range of NOx emissions from 95 to 914 tons in a year. Given the wide range of NOx production the utility of this information is suspect. The EPA recognizes a standard factor of 17 lbs (NOx)/ton (ANFO) however this factor is based on chemical composition and does not address contamination, confinement, or AN to FO ratio. This factor when applied to the West Virginia Mine's explosive consumption produced a value of 215 tons of NOx. There is a lack of information on NOx emission from emulsion type explosives. The work presented in this paper can be used by blasting professionals to quantify NOx emissions and guide future work for producing better predictor factors.

Jan 1, 2014

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004