Search Documents

By G E. Exedaktylos, Y Zhou

The complex and non-linear nature of blast fracturing has restricted common bract design primarily to empirical approaches. The code developed for this investigation simulates the pattern of interacting radial fractures from an array of blastholes, at various burdens and spacings, and in simultaneous and delayed modes. The resultant pattern is analyzed and a fragment adze distribution calculated.

Jan 1, 1989

By Dale Preece, Stephen Chung, Richard Jensen

DMCBLAST_3D is a three-dimensional extension of the proven two-dimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2001

By Trevor Garbutt, Peter Bellairs, Jason Sander, Glenn Shaw

The Yarrie Iron Ore mine is located in the Pilbara region of Western Australia some 200km eastsoutheast of Port Hedland, the closest large regional centre. The mine is owned by BHPIO who has contracted a large Australian mining contractor Roche Bros to be responsible for the total mining, crushing and trainloading functions. This paper describes a drill and blast optimisation program, resulting from the introduction of a new emulsion matrix called Titan@ Red used to manufacture both HANFO and pumped emulsion ANFO blends.

Jan 1, 1999

By Deane Tunaley, Paul Tidman, Qian Liu, John Mullay

Laboratory studies have indicated that the crystallization and desensitization of microballoon sensitized emulsion explosives start immediately after shocking or pre-compression. However, the question of whether or not the shocked emulsion could be worsened by the growth of crystallization or recovered by rebounding back to lower densities has been rarely examined under actual rock blasting conditions. This study was primarily intended to investigate the desensitization characteristics of two commonly used emulsion products in terms of blasthole spacing and delay duration. In the experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1995

By S. Nakamura, H. Taniguchi, K. Noguchi, H. Sugihara, T. Matsuzawa

It has been reported that expanded poIystyrene and ANFO prills ‘were mixed on a blasting site for controlled blasting (ISANOL). Although there seems to be few possibility of their segregation because mixing on a blasting site is done, there is a great possibility of segregation in packing, transportation and loading of the product due to the different densities of the two ingredients in Japan where mixing on a blasting site still remains inoperative. The fiee-flowing property of ANFO prills was lost with the passage of time because the Abel oil infiltrated into the expanded polystyrene and that gave the product high viscosity.

Jan 1, 2001

By Stuart Brashear, Lee Schettler

"The effect of water on several ANFO/emulsion blend ratios is documented by both physicalobservations and analytical testing to demonstrate the effect even small quantities of water canhave on water resistant blends."

Jan 1, 1996

By D Schneider, H Elliott

The advantages and disadvantages of using inclined boreholes in blasting has been under discussion for a long time. Some recognized disadvantages are that drilling costs, both operating and capital costs, are higher for inclined holes than for vertical ones, and that drilling accuracy is more difficult to maintain. People who have used angled holes in practice, on the other hand, have claimed that the quality of blast results was improved. In fact, their popularity has increased, especially in Australia.

Jan 1, 1988

By Chang-Ha Ryu, Hyung Yang, Hyung-Sik Yang

Ground vibration by rock blasting causes many environmental problems to adjacent structures and human bodies. Growing concerns have been given to the effects of dynamic loading induced by blasting works near safety-related structure like nuclear power plant, hospital, broadcasting station, research institute and tish farm, etc. In order to ensure the safety, rational safe criterion should be established. It requires development of a model to predict the design parameters through more systematic measurement and analysis. Primary estimation by adequate model with general parameters will be very useful for safe design and understanding the possible hazards in advance.

Jan 1, 2001

By Dale S. Preece, Stephen H. Chung

"In bench blasting, the distribution of loaded explosives with respect to the burden rock has strong effects on digging especially at the toe area. Blast design often focuses on other results such as percent-cast or fragmentation, sometimes leaving a diggability problem at the toe of the blast that is not discovered until excavation. A method for assessing the influence of blast design on diggability has been developed. This method relates the kinetic energy and rock displacement experienced by the material in the muckpile to its diggability. Simulation of the blast along with the calculation of kinetic energy and diggability is done with the discrete element computer program DMC_BLAST(DMC: Distinct Motion Code)."

Jan 1, 1999

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines has developed computer software to study the effects of initiator scatter on all aspects of the blasting process. The software is useful because it is difficult to obtain actual initiator data, particularly the standard deviation which is needed to express initiator scatter. The new software is structured to allow blasters to answer the question: how precise must initiators be to insure a successful blast? Successful is defined statistically in terms of a confidence level. The software can be used with any possible design since there are no restrictions due to size or complexity.

Jan 1, 1992

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

By J Lyall Workman, Peter N. Calder

The Manassas Quarry is a large industrial stone quarry in Northern Virginia owned and operated by Vulcan Materials Company. The quarry experienced instability in a portion of the north wall, which included toppling failure in a metasediment and movement on a major fault zone. It was necessary to take remedial measures to stabilize the wall and create good quality final pit walls.

Jan 1, 1992

By Virgil J. Stachura, Larry R. Fletcher, Paul V. Sterk, Matthew N. Plis

The large diameter blastholes now being used in underground mining have caused concern because of their increased potential for damaging openings and creating rockfall hazards. In response to this situation, the Bureau of Mines is conducting research to reduce the amount of overbreak and damage to the perimeter of underground openings. This paper presents the results of tests with decoupled charges in 6.5 inch diameter blastholes, and unloaded guide holes, in Vertical Crater Retreat (VCR) stope panels at the Homestake underground gold mine in Lead, SD.

Jan 1, 1991

By Tom Short, Bill Beam

Some of the weapons testing shafts at Mercury, Nevada require depths of 1000ft and diameters of 10 feet. The top 40 feet to 65 feet is drilled, blasted and excavated by Large caisson type augers in order to provide vertical working room for the placement of large, oil field type, drilling rigs and the required drill collar.

Jan 1, 1991

By R C. Berglund

Since the Republic Mine began production in the mid 1950's, drilling and blasting practices have continually changed. In recent years, progress has been achieved through the development of more precise blast engineering methods, in greatly increasing the use of non-water resistant ammonium nitrate explosives, and in changing to a non-electric in-hole delay initiation system. Also, recent experience indicates that ammonium nitrate fueled with nitropropane and methanol is a viable substitute for aluminized AN-FO.

Jan 1, 1980

By Sri R. B Singh

Based on CMRI investigations in nearly 50 mines, the authors have developed two empirical formulae for the effective determination of burden and spacing in any kind of rock deposit. Along with charge loading parameters, decoupling effect and bench height, the equations consider rock characterisation parameter by incorporating 'RQD' i.e Rock Quality Designation. The value of 'RQD' may be obtained either by core recovery using diamond drilling or theoretically from the characteristics of joints or bedding planes. The derived equations may be used in any rock mass under varying geologic and charge loading conditions. The Formulae suggested herein, are explicit, simple in form and easily applicable in field purposes. The values obtained from the present equations are verified against various field data generated by CMRI during the past several years.

Jan 1, 1998

Current research in comminution includes efforts to increase the efficiency of mineral processing systems and reduce the amount of electrical energy needed for size reduction. In most mining operations, comminution begins with blasting. Normally, blast design focuses on loosening material for excavation and sizing the product for efficient haulage. It is likely that blasting also results in internal damage to rock fragments within the blast pattern which may provide subsequent comminution benefits. If substantial comminution benefits exist, appropriate modification to blast pattern design may reduce the overall electrical energy needed for mineral liberation.

Jan 1, 1996

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993