Search Documents

By Jim Rix, Ken Been, Nihal Bohra, Anthony Rice, Juan Lopez

"A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads.The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles."

Jan 1, 2017

By Nihal Bohra

A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads. The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles.

Jan 1, 1995

By Donald R. Clark

"Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0.Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs.The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths.Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary"

Jan 1, 2017

By Donald R. Clark

Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0. Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs. The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths. Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary design.

By Stephen Darmawan, Mahdi M. Disfani, Arul Arulrajah, Alireza Mohammadinia

Deep mixing using cementitious compounds is an in-situ method of ground improvement for improving the strength, compressibility of loose sand. Artificial light cementation can increase the stiffness of loose sands significantly and reduce the settlement of loose deposits. The increase in contact area between the particles with a thin layer of cementitious agent depends on the confinement and void ratio of the soil mass. Hence, the stiffening effect of cementation not only depends on the type and amount of cementing agent and inter-particular force chain of loose deposit but also depends on the stress level at the time of cementation. In addition, the cementation effect in loose deposits can be deteriorated at relatively low strain levels. Decementation softening can cause detrimental and irreversible impacts on the soil deposit. This study investigates the effect of initial confinement and subsequently the initial void ratio at the time of cementation on small strain behaviour and decementation softening of cemented loose sand under ko loading. The effect of inter-particular contact of sand particles based on the specific surface area and also soil density was also investigated by means of shear wave propagation. This study present insightful information on effect of primary consolidation stress levels, density of soil and cementation level on softening and collapse of loose deposits improved using deep soil mixing technique. Better understanding of soil-cement interaction by optimization of binder content for deep mixing activation can lead to increasing the level of confidence in using this technique in ground improvement applications.

Jan 1, 1900

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

Jan 1, 2001

By Leykam Chris J., Jacobs Scott. A.

"Construction of the New NY Bridge over the Hudson River 25 miles north of New York City is one of the largest civil infrastructure projects presently underway in the United States (formerly Tappan Zee Hudson River Crossing). The $3.14 billion Design-Build contract is also the largest ever awarded by the state of New York using an Alternative Project Delivery method, and the first major public project to use Design-Build. The new 3.1 mile long bridge will replace the existing Governor Malcolm Wilson Tappan Zee Bridge with a modern twin crossing featuring: Iconic side by side cable stay main spans; significant deck widths accommodating eight lanes of regular traffic, wide shoulders, and a shared use pedestrian and bike path; foundation with excess capacity to fully support a future rail bridge; more than 1,000 large diameter pipe piles driven in deep glacial deposits; drilled shafts installed through steep blast-rock slopes on the east shore landings. Geotechnical challenges included varied bedrock and glacial till surfaces with steep slopes and depths in excess of 750 ft.The purpose of this paper is to highlight major features of the New NY Bridge project with specific focus on the design and construction of the foundations supporting the approach and main span structures from abutment to abutment, provide background on alternative project delivery in NY, as well as provide an overview of the design-build process as it was applied to foundation delivery.The 3.1 mile Governor Malcolm Wilson Tappan Zee Bridge was constructed across the Hudson River connecting Nyack and Tarrytown (Rockland and Westchester Counties). Construction started in March 1952 and was completed in 1955 for a cost of $81 million. The seven lane crossing first opened to traffic on December 15, 1955 and coincided with the opening of a 28 mile segment of highway I-87 / I-287 between Suffern NY and Yonkers NY. The bridge is part of the extensive 574 mile New York State Thruway road system owned and operated by the New York State Thruway Authority (NYSTA)."

Jan 1, 2016

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By Arjan Jovani, Arjan Beqiraj, Përparim Alikaj, Altin Karriqi

"Koman dam is one of most important high dams in Drin River Cascade. Safety of these dam is very important not only in power production but also in social and environmental aspects connected with vital activity of local people living in downstream of Drini River and in economic development of the country. In December 2014, during the rehabilitation works on some protection measures at the downstream dam toe, a considerable amount of water leakage emerged from the dam toe. This was noticed even before, but its amount and physical-chemical properties were not evaluated. In order to study the origin and flow direction of this water leakage, KESH sh.a. (Albanian Power Corporation) realized Geophysical and Hydro chemical surveys, turbidity and flow measurements and respective analyses of them. Geophysical survey consist in Apparent Resistivity surveys and Self Potential survey. The survey was done in 3 lines using Resistivity “Real Section” technique. Results are plotted in Sections and plan maps of resistivity and SP parameter. There are defined possible leakage areas and the main flow directions are defined. Also, there is done a hydro chemical analyse. Nine water samples were taken from the different places as Komani lake, service galleries of dam, dam toe and two karst springs which were analysed for both physical-chemical parameters and isotopic composition of O-18 and D. The attained analytical data found that water from the dam toe leakages shows the same chemical signature and isotopic composition of O-18 and D as the water from the lake, thus confirming the hydraulic connection between them.Also, There is done the analyse of water leakage turbidity and amount of this leakage"

Jan 1, 2016

By Guo Qian, Du Guangyin, Deng Yongfeng, Liu Songyu, Wang Ningping

"Metakaolin (MK) can efficiently enhance the strength and the impermeability of concretes and mortars. However, it has rarely been attempted in admixtures of cement-stabilized soils until presently. As deep mixing method is wildly used in ground improvement, the strength of cemented soils (soilcrete) and the applicability of the MK should be considered. This paper focuses on the macro-strength development of cement-stabilised silty soil mixed with MK. The result shows that the addition of MK can enhance the unconfined compressive strength of the soilcrete, which attributes to a combination of the rates of OPC hydration and the MK-CH reaction. Note that the strength of soilcrete was influenced by the properties of soil, water-to-binder mass ratio (W/B) in admixtures, which needs to be reconsidered since the binder mass composes that of cement and MK totally.INTRODUCTIONCement was used in ground modification techniques, such as the jet grouting, deep mixing method (DMM) which was put into practices in Japan and Nordic countries in the middle of the 1970s, and then spread to China, South East Asia[1]. For last decades, fly ash, slag or silica fume was mixed with cement to form the new cement base stabilizing agent in the view of economy and performance improvement. The mechanical behavior of these soil-binder admixtures (nominated as “soilcrete”), was investigated. But the soilcrete modified with the metakaolin (MK) was still not investigated much and lots of further work needs to be conducted.Some laboratory experiments of the soilcretes modified with MK have been taken[2~4]. Kolovos et al. (2013) indicates that the unconfined compressive strength has a more significant improvement when W/B equals 0.4 than that when W/B equals 1.20 concerning the water-to-binder mass ratio (W/B). Sonebi et al. (2013) investigates the mechanical behaviors of cement grouting containing MK with W/B equals 0.4, and also found the effectiveness of the addition of MK. Zhang et al. (2014) performed the studies on Lianyungang marine clay improvement showed that MK obviously enhanced the quality of cemented soils.In this paper, the strength of soilcrete modified with MK is further investigated, where the unconfined compressive strength at different curing time, the content of MK and cement (w/w) in lab conditions was discussed."

Jan 1, 2015

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Thomas Domanski

Any type of deep excavation whether for Bored Piling, Diaphragm Walls or Contiguous Bored Piling Walls depends on forming a stable borehole with a defined cross-section to receive safely the permanent materials. In modern construction the excavation depth can reach well the range of 100 m and above. The diameters of the Piles reach often sizes of 2.5 m and bigger. Top casings in Bored Piles (Diaphragm Wall none) are rather short and stability below the casing, need to be secured by stabilization slurry. The boreholes need to be formed through a variety of different materials and stand open for an extended period. Without a safe stable borehole, it is impossible to produce quality products and work cost-efficient. The understanding and proper usage of a suitable slurry is a key element essential for the delivery of Foundation Elements with high quality and within a reasonable budget. The setting of mechanical and rheological parameters in specifications is necessary and helpful, but probably insufficient to embrace and control such a key element in the practical implementation of foundation construction. The proper selection, design, implementation and supervision of slurries on site requires both from Contractors and Engineers to understand how different slurries do function. Only with this knowledge the right decisions in slurry operations can be made. This talk is directed to give some help to both, Contractor’s and Engineer’s, in understanding how different type of slurries do work. (Which ones should be preferred in what kind of soils.) The better knowledge will help the Contractor to control cost and enhance production. The Engineer will be able to assist in arriving at the appropriate technical choices and include in the specifications.

Sep 1, 2022

By D. K. ] [Gupta

The Foundations of the Shear keys and alround cut off for Power House -IV of the Western Yamuna Canal Hydroelectric Project at Bhudkalan, Haryana were to be laid at a depth of 26M below the N.S.L and 24.4M below ground water table. The foundation of the drainage sump was to be laid at still higher depth, Viz 29.OM below N.S.L. The Sub soil at the site consisted of Gravel with some amount of sand. The laying of the foundation at such a great depth, at a large depth below the ground water table and that too under such difficult sub-soil conditions encountered a large no of Geotechnical problems-viz excessive seepage, side slope sloughing and sand boiling during excavation. Under the circumstances at the site, the modified foundation construction procedure i.e a battery of M. S. Troughs was placed in flowing water conditions and concreted thereafter, resulting in a sizable cut in dewatering and reducing a significant amount of time and cost of construction affecting a saving of crores of rupees at the state exchequer. Sheet Piling was used to prevent side sloughing in the foundation pit.

Jan 1, 1996

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006