Search Documents

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By Alberto Carmona Rosell, Sri Ram Ramankutty

"The installation of Bored Piles and Diaphragm Wall under slurry using tremie raises quality concerns on the integrity of concrete. It is vital to understand the effects on concrete integrity during concrete pouring process. This paper intends to unveil to what extent the compressive strength of the concrete pour is affected in contact with drilling fluid still. Another important angle of analysis proves whether the inclusion of solids particles of un-hydrated fluid could have impact on the concrete compressive strength. The testing comparing the response of concrete compressive strength when drilling fluid is included into the concrete mix altering the water/cement ratio by 5%, 20% and 30%. Comparative results are analysed between two different hydrated slurries namely sodium activated Bentonite and 3rd generation synthetic polymer.1. INTRODUCTIONSoil stabilization is the base for a successful deep foundation execution. The G3 System Slurry developed by Ground Engineering Operations (GEO), with its third generation polymer, namely PolyMud®, is an innovative and unique alternative to the mineral based slurries for soil stabilization, enhancing the quality and integrity of the underground foundation structures. It optimises the production rate of work progress and cost as well. At the same time, PolyMud® slurry is proven to be environmentally friendly.Guaranteeing the maximum quality of the foundation elements according to the initial design is one of the most important objectives and a concern for the foundations contractors. In order to fulfil the project expectations in this aspect, any incident that could compromise the designed concrete integrity and capacity must be avoided.GEO, has carry out its own research regarding effects on the concrete compression results if drilling fluid intermixes with fresh concrete while pouring. To shed light in this regard, GEO, in collaboration with CML (Concrete Materials Laboratory) Sdn. Bhd., carried out empiric tests that analyse this particular event from different perspectives, bringing up the corresponding results that will be studied and commented in this article."

Jan 1, 2015

By Bidjan Ghahreman

A total of 120 micropiles were constructed for foundations of a new selective catalytic reduction (SCR) unit in a coal-fired power plant east of Kansas City, Missouri. Construction was performed under restricted overhead conditions because of the existing facilities. The subsurface profile included about 70 feet of overburden composed of granular fill, stiff to very stiff cohesive material, medium dense sand, and very dense gravel. The bedrock was composed of alternating layers of shale and claystone (weak rock) and limestone (strong rock). It was decided that the bond zone would be entirely in the bedrock. The design rock profile along the bond zone was composed of 10 feet of shale and claystone underlain by 10 feet of limestone, which in turn was underlain by shale and claystone. To achieve the design compression and uplift capacities of 100 tons and 60 tons, respectively, a length of 23 feet was determined for the bond zone. Compression and uplift load tests were performed to verify the design. IBC-2000 elastic line, Decourt (1999) extrapolation, and Chin-Kondner extrapolation were used to interpret the load test results. The interpretation of load test data indicated that both compression and uplift capacities far exceeded the respective design loads. Spring constants of 397 tons per inch (T/in.) (in compression) and 290 T/in. (in uplift) were estimated from load tests at respective design loads. During the compression load test, no sign of creep was observed after the applied load was maintained at the design load (100 tons) for two hours.

Jan 1, 2009

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Yahia M. Al-Smadi

Effect of lateral loading against existing sheet pile wall and distribution of gravity loading due to various number of construction loading scenarios were studied. The objective of this effort was to determine the loading case that permits the contractor to utilize a 400 ton crane at the specified location with the existing limitation imposed on site. Staged analysis was determined as the methodology that will more accurately predict the exiting and additional stress due to the impose crane loading. A reliable and robust analysis (ANSYS) software was used to complete both 2D and 3D finite element model and analysis. Analysis model parameters such as material properties, non-linear behavior of the soil, and meshing are presented and discussed. At the conclusion specific range of crane operation and pick weights operating on existing concrete mat supported on top of an existing tunnel was reviewed and deemed acceptable.

Jan 1, 2010

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By A. C. Galvis-Castro, R. Salgado, M. Prezzi, E. Ganju, R. D. Tovar-Valencia

It is generally accepted that the unit shaft resistance of piles in sands is lower for tensile loading than for compressive loading. So far, very little attention has been paid to the influence of the installation method on the tensile-to-compressive unit shaft resistance ratio. The objective of this paper is to analyze the effect of installation method on the ratio of unit shaft resistance in tension to that in compression for a model pile installed in a dense silica sand. To study installation effects, load tests on model piles were carried out in a half-cylindrical calibration chamber with digital image correlation (DIC) capability. The model piles were either jacked in one stroke using a constant rate of advance, or pre-installed into the dense sand samples. Digital images of the model pile and sand were taken during the load test and processed using DIC to obtain the displacement field in the sand. It was found that unit shaft resistance was essentially the same in tension and compression for the pre-installed pile, however for the jacked pile, the unit shaft resistance in tension was approximately half of that in compression. DIC analysis revealed that: (1) during the load test, more displacement occurs in the soil domain for the pre-installed pile compared to the jacked pile, (2) for the jacked pile, the magnitude of displacement in the soil domain is greater in tension than in compression and (3) for the pre-installed pile, the magnitudes of displacement in tension and compression are similar. INTRODUCTION Pile foundations can be categorized into two main types depending on the method of installation: displacement piles (e.g., jacked or driven piles) and non-displacement piles (e.g., bored piles or drilled shafts) (Basu et al. 2010; Salgado 2008). The response of these piles to loading can be studied in the laboratory by means of calibration chamber experiments on model piles that are either jacked into the samples, representing displacement piles (Jardine et al. 2005; Lee et al. 2011; Tovar-Valencia et al. 2018), or pre-installed in the sand sample, representing non-displacement piles(Galvis-Castro et al. 2019a; Le Kouby et al. 2013; Tehrani et al. 2016)

Jan 1, 2019

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By Joseph T. Coe, Siavash Mahvelati, Philip Asabere

Characterization of existing foundations remains an important issue as foundation reuse and rehabilitation continue to garner increased attention. In the case of unknown foundations, geophysical and nondestructive testing (NDT) methods have been utilized in the past to evaluate foundation geometry and could serve as useful tools in the case of foundation reuse. A comprehensive study was initiated in the late 1990’s and early 2000’s that evaluated the effectiveness of the available geophysical and NDT technologies to characterize unknown foundations for scour evaluation purposes. At the time of that study, the Multichannel Analysis of Surface Waves (MASW) geophysical method was in its infancy and not widely used. Since then, MASW has become increasingly prevalent in geotechnical applications as the method presents a number of potential advantages when characterizing the subsurface, including rapid testing, increased signal to noise ratio, and ability to resolve velocity inversions. This paper presents a case study that explores the abilities of MASW as an unknown foundation characterization tool. MASW was applied to determine subsurface stiffness at a bridge foundation site in the Philadelphia metropolitan area. One MASW survey line was performed immediately over the foundation of interest and another was performed over a control zone adjacent to the foundation to establish a baseline site profile. The purpose of this testing was to examine whether MASW could establish the geometry of the foundation at this site. This paper presents the site conditions and MASW testing procedures, followed by a discussion of data analysis and interpretation.

Jan 1, 2016

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Hamed Ardalan, Mohamed Ashour

"CHAPTER 1INTRODUCTIONThe use of piles to stabilize active landslides or to prevent instability in currently stable slopes has become one of the most important innovative slope reinforcement techniques over the last few decades. Piles have been used successfully in many situations in order to stabilize slopes or to improve slope stability, and numerous methods have been developed for the analysis of piled slopes (Ito et al., 1981; Poulos, 1995; Chen and Poulos, 1997; Zeng and Liang, 2002; Won et al., 2005).The piles used in slope stabilization are usually subjected to lateral force through horizontal movements of the surrounding soil; hence they are considered to be passive piles. The interaction behavior between the piles and the soil is a complicated phenomenon due to its 3-dimensional nature and can be influenced by many factors, such as the characteristics of deformation and the strength parameters of both the pile and the soil. The interaction among piles installed in a slope is complex and depends on the pile and soil strength and stiffness properties, the length of the pile that is embedded in unstable (sliding) and stable soil layers, and the center-to-center pile spacing (S) in a row. Furthermore, the earth pressures applied to the piles are highly dependent upon the relative movement of the soil and the piles."

Jan 1, 2013

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 ft/sec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases, and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

Jan 1, 2013

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By Sepideh Damavandinejad Monfared

In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the beh avior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands.

By Douglas L. Scaggs

Over the past several years, pile foundations have grown to meet the demands of larger and heavier structures. As the foundations have grown, so has the need for larger and more robust piles to carry the increased loads. Seismic considerations have also required larger and tougher piles to withstand the added component of supporting structures during earthquakes. While H-piles, precast concrete piles, timber piles and small pipe piles have been the product of choice, many applications are now calling for much larger piling requiring larger equipment and presenting the contractor with new challenges. This paper is not intended to be a ?how to? guide as much as a discussion on the potential pitfalls a contractor should watch out for when considering a project where mega piles are required.

Jan 1, 2013

By Ivan Hee

The 2.5km long bridge over the Beauharnois Canal and St. Lawrence Seaway is a major structure in the new Autoroute 30 project near Montreal. Foundations for the bridge consist of footings on bedrock, driven piles, and drilled shafts. This paper describes the design, verification, and construction of 1.85m diameter drilled shafts socketed into very strong and abrasive dolomitic sandstone. Two loading tests on sacrificial, heavily-instrumented, 1.18m diameter test shafts using Osterberg load cells were performed, with telltales installed to monitor a possible rock cone failure mechanism. The loading tests resulted in a revision to the initial design and provided a greater understanding of the cone uplift mechanism in rock. Insights gained are discussed and economies of the load testing program presented. Construction methodologies are also presented.

Jan 1, 2011

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By Barry C. Roth

Driving of large piles in water can impact marine wildlife. Bubble curtains can mitigate these adverse effects. The procedures for and preliminary results of monitoring airborne, waterborne and groundborne vibrations with and without bubble curtains on a test project involving 2.438 m piles to 110 m is reported here. We observed fish kills and sea lions apparently fleeing the area. These phenomena were presumably due to the extreme acoustic effects of the powerful hammers which generated waterborne sound intensities locally in excess of 240 dB. This waterborne pile driving noise data collection undertaking is believed to be the most extensive ever attempted.

Jan 1, 2001