Search Documents

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By M. T. Shehata, R. W. Revie, M. Elboujdaini

Environmentally assisted cracks in linepipe steels are initiated either as a result of stresses in combination with environmental effects, as in stress corrosion cracking (SCC), or as a result of trapped hydrogen in the steel, as in hydrogen-induced cracking (HIC). To understand better the mechanism of the crack initiation process, key metallurgical and environmental elements that can affect the cracking phenomena were investigated and are reviewed in this paper. The complexity of both cracking phenomena results from the dependence of SCC and HIC on multiple metallurgical, mechanical, and environmental parameters that may all influence both crack initiation and propagation; e.g., composition, microstructure and non-metallic inclusions in the steel, applied stress, water chemistry in the field, and ionic concentrations in the groundwater near the pipe surface to name a few for SCC. In addition, for HIC phenomena, one can add the concentration of H2S in the fluids transported in the pipe as well as concentration of CO2, pH, etc. In this paper, cracking of linepipe steels is analyzed critically, with particular attention to the crack initiation process. The paper is divided into two parts: The first part covers SCC and the second covers HIC.

Jan 1, 2005

By G. W. H. Norman

"The La Corne molybdenite-bearing veins, discovered in 1915, lie halfway between Amos and Val d'Or near the southwest corner of La Corne township, Abitibi county, Quebec. The Molybdenite Reduction Company, which carried on operations during 1927 to 1930, sank a 200-foot inclined shaft to develop the property and produced about 22 tons of concentrntes from a 30-ton mill during 1929. Hollinger Consolidated Gold Mines, Limited, carried on further underground exploration in 1930. The Molybdenite Corporation of Canada drilled a part of the property in 1938 to 1939 and produced 1 ton of concentrates in 1938. Wartime Metals operated the property from 1942 to July 15, 1945. At this time the mill was enlarged to treat 200 tons daily. Molybdenite Corporation of Canada since July 15th, 1945, have continued the operation of this property and have revised the mill flow-sheet in order to produce both a bismuth and a molybdenite concentrate.The production for the period 1942-1946 is as follows:Total molybdenite production from the mine in the 1942 to 1946 period was about 4,127,400 lb.The La Corne deposit occurs at the northwest contact of a small mass of biotite granite with biotite schist. The form and extent of the biotite granite mass is concealed by a wide sand plain that extends northwest and west from the deposit and overlies bed-rock except in four small outcrop areas. These are spaced 1,000 and 2,000 feet apart along a narrow strip extending 5,000 feet south from the mine. The outcrops suggest that the granite must be at least 1,500 feet wide and 3,000 feet long northeastward. Where exposed in the mine workings the contact dips 70°N.W., but is not a sharply defineable feature due to the presence of numerous granite dykes and tongues in a zone of biotite schist 100 feet wide along the margin of the granite. The biotite schist in the few outcrops that flank the north and south sides of the granite strikes northeast and dips 60° to 70° S.E."

Jan 1, 1954

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

By C. Feng, D. W. M. Arrigan

Arsenic is often associated with gold mining operations and poses a significant health and environmental hazard. While a number of technologies are available for removing arsenic, none of them is effective under all conditions. Although adsorption is a promising approach, most methods focus on the purification of water under neutral or acidic conditions and tend to be less effective in gold mining process waters, operating under alkaline conditions. In this study, the removal of As (III) and As (V) from both arsenic-only solutions and simulated process waters using composite magnetic nanoparticles was investigated. The nanoparticles consisted of magnetite (Fe3O4) or maghemite (?-Fe2O3) cores covered by various metal oxides with Langmuir adsorption capacities of As (III) and As (V) ranging from 31.4 to 79.1 mg/g and 10.2 to 25.5 mg/g, respectively, in arsenic-only solutions at pH 9. Their adsorption capacities were further recognised by the adsorption tests conducted in simulated process waters. The ability to remove As (III) is of particular importance as it is harder to remove it from alkaline solutions. The magnetic cores allow simple and efficient magnetic recovery of the As-loaded nanoparticles.

Jan 1, 2017

By J. M. Carr

The history, geological setting and local geology of the Magnum vein system, 100 miles west of Fort Nelson in northeastern British Columbia, are described. The system comprises a number of quartz-ankerite veins, mineralized with chalcopyrite and lesser pyrite, occurring in a steep northeastly zone of deformation and subsequent dike intrusion within otherwise little-deformed Precambrian sedimentary rocks. In April of 1970, Churchill Copper Corporation began producing copper concentrates in a 750-tpd mill fed from the Magnum mine.

Jan 1, 1971

By M. A. Cawley, J. W. Jordan

"IntroductionTHE ORE PILLARS in the lower ""A"" ore body of Waite Amulet Mines, Limited, can be divided into two groups, those mined in the open by sub-level blast-hole methods, and those to be mined .against coarse rock fill. Of the three pillars in the last group one has been mined and is dealt with in this paper. The method of mining pillars against coarse rock fill was suggested by the late Dr. Oliver Hall, who was Consulting Engineer for the Company when recovery of No. 2 East pillar was being planned.HistoryThe Waite Amulet mine is in northwestern Quebec, nine miles north of the town of Noranda. The property is approximately three miles long by one mile wide. The present Company, which was formed by the amalgamation of Amulet Mines, Limited, and Waite Ackerman-Montgomery Mines, Limited, commenced operations in the summer of 1937. In the fall of 1939 a new .flotation mill was erected with a capacity of 1,200 tons per day, which was increased to 1,800 tons per day in 1943. The mill is presently operated at 1,400 tons per day.To date, seven orebodies have been found, the major ones being Lower A, East Waite, and Waite. Three separate concentrates are produced, copper, zinc, and pyrite. Total tonnage mined to the end of 1954 from all orebodies has been 7,340,000 tons, which averaged 4.6 per cent copper, 5.3 per cent zinc, and 0.037 oz. gold and 1.27 oz. silver per ton."

Jan 1, 1955

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By C. Jewell, G. H. Rupay

"67 - 2:15-3:00Regeneration of Hydrochloric Acid from Waste Pickle Liquor Using a Fluidized Bed Reactor System. G. H. RUPAY and C. JEWELL, Dominion Foundries and Steel Ltd., Hamilton, Ont.The disposal of acidic waste liquors from pickling processes has always been a problem for the steel industry. With increased awareness toward environmental control and the problems acidic wastes create, processes utilizing recovery and regeneration of the waste acids are becoming more popular. This paper describes the Keramchemie/Lurgi process for regenerating hydrochloric acid from waste pickle liquor using a fluidized bed reactor system. The process parameters are outlined, together with a brief description of the equipment. This is followed by a discussion of the operating problems and concludes with economic data."

Jan 1, 2000

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By W. Abdellah

Underground mine developments, such as haulage drifts and cross cuts, play a vital role in providing access to ore extraction areas for mine production. The stability of mine developments is thus of crucial importance during the life of a mine plan. Many Canadian mines use longhole mining methods or one of its variants. These methods require access to the orebody through mine developments such as haulage drifts and cross cuts on multiple levels. This paper examines the stability of mine development access intersections with respect to the planned mining sequence. A case study, the #1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario, is presented. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) was created for a development intersection situated 1.5 km below ground surface. The stability, or performance of the intersection, is evaluated in terms of the strength-to-stress ratio. The ratio threshold is set at 1.4 for temporary openings. Unsatisfactory performance is defined as a strength-to-stress ratio less than this threshold value. The performance of the intersection stability is evaluated at various modelled mining stages and the probabilistic method of analysis is then invoked to study the probability of unsatisfactory performance of the intersection. The results are presented and categorized with respect to probability, instability, and mining stage.

Aug 1, 2013

By A. L. Mular

This paper provides a worthwhile contribution to the knowledge needed for calculating and using mathematical models of grinding circuits. The computer search algorithm proposed should remove much of the guesswork as well as reduce computer processing costs and improve the accuracy of estimated parameter values for grinding mill models.

Jan 1, 1970

By J. Contreras

In the period 2003-2004, the situation of the copper concentrate market was unfavourable for smelters and refineries, with low TC/RC values and euro-dollar parity affecting European companies negatively. Within this scenario, Atlantic Copper decided to develop a plan to increase its competitiveness and to improve its results in these market circumstances. The plan affected all departments in the Company and was based mainly on cost reduction in energy and manpower. A general analysis of the Complex's overall efficiency was carried out and, based on this analysis, two major Projects emerged, "Primavera" and "KF". Each Project consisted of smaller sub-projects which aimed at improving the areas which could perform better according to our general analysis. The paper describes how this entire project developed and the final results obtained by the Company.

Jan 1, 2007

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

In this study, we develop a detailed model of the likely future carbon footprint of primary copper supply. We develop a peak copper production model, based on a detailed copper resource data set, and combine this with a comprehensive life cycle assessment model of copper mining and milling to predict greenhouse gas emission rates and intensities of Australian and global copper production up to 2100. By establishing a quantitative prediction of both copper production and corresponding greenhouse gas emissions of Australian and global copper industry, we then analysed the emissions intensity of various energy input scenarios, such as business-as-usual, solar thermal electricity and solar thermal electricity with biodiesel. The Australian Government has an aspirational goal for long-term greenhouse gas emissions of an 80% reduction from the 2000 level by 2050. For the copper sector, this means moving from about 12.6 Mt CO2e in 2000 to a goal of some 2.52 Mt CO2e in 2050 (assuming equal emissions reductions across the economy). Based on the energy sources modelled, only the solar thermal plus biodiesel scenario was capable of achieving this goal at about 0.15 Mt CO2e, since the solar thermal alone scenario still includes normal petro-diesel as a major source of emissions. Overall, it is clear that there are abundant resources which can meet expected long-term copper demands, the critical issue is more the carbon (and environmental) footprint of different copper supplies and use rather than how much is available for mining. It is clear that the switch to renewable energy can have a profound impact on the carbon intensity of copper supply, even allowing for increased energy intensity as ore grades decline, and a complete conversion to renewable energy will position the copper sector to meet existing annual greenhouse gas emissions targets and goals.

Aug 1, 2013

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014