Search Documents

By I. V. Kojo

Continuous development of technologies has been self-explanatory for Outokumpu Technology's engineers for decades. The aim in the development has always been the improvement of profitability of the copper production but also the sustainability of the processing i.e. high copper recovery, low external fossil based energy utilization, high emission captures and of course low operation and investment costs. Outokumpu Technology's long-term view of the development is a change towards continuous processes and elimination of number of unit operations in smelting i.e. elimination of possible sources of emissions. Outokumpu blister smelting processes i.e. Outokumpu Direct-to-Blister Flash Smelting and Kennecott-Outokumpu Flash Converting have shown excellent operational results during the years of operation and it is expected that soon more than 10 % of the world primary copper is produced by these technologies. The paper will give some background of this development trend.

Jan 1, 2007

By Mohamad Kharseh

There is general acceptance that climate change, which is the most important challenge facing humanity, is anthropogenic and attributed to fossil fuel consumption. Therefore, improving the performance of our existing energy systems and deploy more renewable energy resources is an urgent issue to be addressed. Geothermal refers to existing of heat energy in deep rock and sedimentary basins. This energy can be used to drive a power turbine to generate electricity. Traditionally, geothermal has been exploited in places with the plentiful hot water at relatively shallow depth. In the light of fact that ground temperature increases with the depth everywhere on the Earth, engineered geothermal systems (EGS) can be installed in any place to exploit the geothermal in generating energy. Unfortunately, the high exploration and drilling costs of boreholes is the main barrier to commerciality of EGS worldwide. In addition, there are technical problems associated with drilling big depth. In oil producing countries such problems can be addressed by utilizing whether active or abandoned oil or gas wells and, consequently, EGS can produce power at profit. The current study presents an analysis of a binary geothermal power generation system for commercial electricity generation in Qatar. For this purpose, two binary cycles are assumed the main difference between them is that the first one is air cooled while the other will be water cooled. The performance of the two cycles and the possibility of improvement has been shown. Economic analysis the power plant shows that the levelized costs of electricity is 3.6US¢/kWh and the pay-back time is less than 8 years.

Aug 1, 2013

By R. T. McAndrew

Introduction Drinnan is situated in the Prairie Creek coal area in the Foothills belt of Alberta. It lies on the main line of the Canadian National railway from Edmonton to Jasper. The exact location is shown on the map (Figure I). Interest in the field was aroused by several circumstances: Its proximity to Brule and Pocahontas on the southwest and to Coal-spur on the southeast led to the belief that coal might be economically produced here. There was already at Hinton a 3 ft. 9 in. coal seam being mined by Seabolt. The coal was of very good grade, being black and shiny in appearance with well defined cleavage and a heat value of 12,000 B. t.u. Outcrops of coal had also been noticed on the north side of the Athabaska river and Fish creek. These facts led the Jasper Coal Company to investigate the field. This Company considered taking over the Seabolt property at Hinton, but, owing to the size of the seam, this plan was abandoned and prospecting by diamond drills and test pits was started two years ago in the district east of Hinton. After prospecting had been completed, the most favourable district was found to be in township 51, ranges 24 and 25, west of the 5th meridian. The Company's lease includes all or parts of sections 18, 19, 20, and 28 in range 24, and sections 10, 11, 12, 13, and 14 in range 25. The approximate boundaries of the property are the Canadian National railway on the north, Happy creek on the west, and Cache Percotte creek on the east. The lease comprises 3,100 acres, and the total amount of coal in sight is estimated at 100,000,000 tons.

Jan 1, 1931

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008

By D. L. Churcher, R. J. Perry

"In recent years much work has been don e to examine alternate underground backfill support systems with the objectives of improving ground support and reducing mining costs. This report deals with the work conducted at Placer Dome Inc.’s Dome Mine to develop a high density backfill system, taking advantage of the unique properties of this fill material, to address a backlog of large open stopes to sustain stable minewide ground conditions for future generations of Dome miners.IntroductionDome Mine began its existence in 1909 with the discovery of visible gold on a dome shaped outcrop located west of Porcupine Lake in northern Ontario. The orebody beneath this outcrop has supported one of Canada’s premier gold mining operations for 80 years. Production during this time of over 46 000 000 tons of ore has resulted in the recovery of II 500 000 ounces of gold and 2 000 000 ounces of silver. Mining continues today at a production rate of 3500 tons per day, with ore coming from both underground and open pit operations.During the life of the mine, different underground mining methods have been used to extract the ore from a complex deposit consisting of single and multiple vein structures.Cut-and-fill mining was introduced in the 1930s using sand fill and later hydraulic fill for support and to provide a working platform. A total of 1 800 000 tons of sand fill and 7 300 000 tons of hydraulic fill have been placed underground in cut-and-fill stopes. Until the late 1960sshrinkage mining was used extensively, particularly in narrow, steeply dipping zones. Bulk mining with small diameter longholes was introduced about this time, to take advantage of low production costs. Longhole blasting has often been used to recover low grade ore from the walls or sills of old shrink stopes, resulting in large open stopes. Backfilling of these open holes has been restricted to smaller stopes and associated with local ground conditions.In the late 1970s it was recognized that the number of large open holes which were being generated presented serious regional and minewide stability problems for future operations. With higher gold prices, economic ore reserves were being tied up in areas adjacent to multi-level open stope complexes. To stabilize these stopes and allow access, backfilling would be required."

Jan 1, 1990

By Jonathan Peck, Jim Gray

"While the mine developer looks for bigger and better orebodies in countries offering lower risks to development capital, the opera-tor of existing mines is looking for bigger and better ways to use his existing resources. Mining operations today utilize a variety of stand-alone systems for planning and managing their operations. In both small and large mines, payroll, accounting, inventory, planning, and engineering requirements are met using a combination of manual and computer-based systems.Technical advances and new enabling technologies are changing how mines are doing business. PC-based systems are allowing small operations to join the larger mines in using advanced computer-based systems. Advanced monitors are being used in maintenance to track, predict and correct the health of production equipment. Production monitoring systems are used to measure the performance of operating equipment and personnel in real time. This detailed information on how much, where, when, and by whom is being used for proactive management and planning. Ultimately, this information can be used to optimize and control the machines’ activities, eventually leading to robotic and autonomous operation of mining equipment.As the use of technology increases in mining, specific information objectives are being met but other problems are being created. The life cycle of technology is small, and as current systems are replaced by newer ones, integration problems and additional end-user training are created. In addition, onboard monitoring systems can create large volumes of data, data which are frequently archived without being analyzed. Mine operators are also duplicating efforts applying new technologies in an effort to be more competitive, but in doing so are creating interfaces which are only compatible with their own facilities. As system development moved from the centralized mainframe computer to the PC environment, the fragmentation of these systems became more pronounced.To efficiently continue in adapting and utilizing advancing technology, the mining industry needs to develop a system architecture that readily integrates as many sub-systems as possible. This will provide a framework for existing system integration and design guide-lines for future development. The Total Mining System (TMS) concept will allow a network of stand-alone functional modules to be readily integrated with minimal effort. This paper will discuss some of the current technologies cur-rently in use in some surface mine operations.In addition, a description of the information system and communications requirements that will be needed to integrate these components in the future, will be discussed."

Jan 1, 1996

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors' project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant's design output level.

Jan 1, 2011

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

By R. De Ruiter

"In times when mines are emphasizing cost reductions, a properly rebuilt shall conveyance can be more cost-effective than building a new unit. Awareness of the safety aspects of conveyance design along with proper maintenance playa large part in reducing operating costs. A knowledgeable operator can maintain a high level of safety and significantly lengthen the service life of a conveyance. Such an operator is also in a better position to determine when a major overhaul is necessary.After the decision has been made to rebuild, operators must decide who will do the overhaul. Whether the work is to be done in-house or contracted out, the goal is to achieve a conveyance recertified to ""as new"" condition. By dealing with conveyance rebuilds as an engineered product, operators can be certain they are getting a top quality product for their money.This paper deals with the engineering aspects of conveyance rebuilds. Actual examples of typical problems are discussed and corrective action outlined. Design considerations such as proper material selection, component fatigue due to cyclic loading, effects of stress concentrations and corrosion are all part of the initial design considerations that must carryover into the rebuild process. All too often equipment overhauls are done by people who are not experienced in conveyance design.As a manufacturer of mining equipment, Wabi has gained expertise over the past 70 years. By sharing this knowledge the company hopes to create a safer work environment and help to reduce operating costs."

Jan 1, 1994

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

By S. A. Pence, A. I. McCallum, V. de Korompay

"Special salt protection rings containing a water-swell• able, polymeric sealant are in successful operation in Canadian potash shafts. Installed above the Prairie Evaporite salt formation at a depth of 3,000 feet, the sealant is preventing formation water migration into the salt and pressure build-up on the concrete lining of both production and service shafts. The salt protection rings are not under the hydrostatic pressure of the formation water.The chemical sealant in use has the unique property of imbibing water and swelling. •Therefore, any water at• tempting to flow by the seal ring actually produces a tighter seal.The purpose of this paper is to discuss the sealant and its properties and uses. Installation of the material and its operation in two Canadian mine shafts is described."

Jan 1, 1971

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

By Bruce A. McFarlane

"I WOULD LIKE TO SAY how honoured I am that I have been invited to participate in this panel discussion. I have taken the liberty of narrowing my topic somewhat so that instead of speaking on the Sociology of Professions as a whole I will speak on one aspect of it, that is, on Manpower Problems in the Minerals industry of Canada, with some reference to a new social role for the professionals engaged in this industry. This probably means that I will be encroaching on areas covered or to be covered by other speakers, but I hope that when I do so I will do so from a slightly different vantage point. That is, from a sociological perspective rather than from a historical, industrial, business or professional perspective. I plan to divide my discussion into three areas, namely: (i) problems of ownership and control; (ii) environmental problems; and (iii) manpower and recruitment problems. I do not plan nor am I able to provide clear-cut solutions to the various problems I raise under these three headings. Rather, I hope that my discussion of the problems may form the basis for an extended discussion here and elsewhere. Because of the limitations of time, I will only briefly discuss the first two problem areas noted above – (i) ownership and control and (ii) environmental problems - and I plan to concentrate on the manpower issue."

Jan 1, 1972

According to the principle of similarity, the physical and chemical configurations of a system can be defined by ratios of magnitudes within the system and do not de-pend on the size or nature of units of measurement. In the present work, the similarity principle was utilized in evaluating the reducibility of various iron ores in a rotary batch furnace under optimum operating conditions. It was then used successfully to extrapolate the results, first to the operation of a 20-ft. pilot-plant kiln and then to an industrial-size 80-ft. kiln. By means of this systematic analysis of kiln operation, it was possible to increase the production capacity of the kiln considerably. T HE kilns used by the Strategic-Udy process for the partial reduction of iron ores are, in most aspects, similar to conventional calcining kilns. Iron ore is fed continuously in the upper (feed) end of the kiln and, as the latter rotates

Jan 1, 1964

By Azadeh Riahi

The main goal of this paper is to investigate the effects of permeability anisotropy in Large Open Pit (LOP) mines for problems that exhibit homogeneous anisotropic characteristics. The most important effect of the groundwater flow in open pit mines is on the stability of the pit slopes. This study will investigate the effects of having increased permeability in both horizontal and vertical directions on three aspects of LOP behavior, location of phreatic surface, pore pressure distribution and stability of slopes. The hydromechanical coupling is simulated using a one-way coupling approach. The Shear Strength Reduction method (SSR) is applied to assess the stability of slopes. The studies performed in this paper suggest that anisotropy in permeability leads to a significantly different regime of pore pressure dissipation depending on two aspects, ratio of anisotropy and the relative magnitude of permeability to simulated time. As a result, variation in safety factors and the location and depth of the failure surface must be expected.

Jun 1, 2012

By Rick Coleman, Chelvan (Chevy) Veloo

"P.T. Freeport Indonesia's lrian Jaya Operation has been producing copper concentrate continuously since 1972. Numerous ore discoveries and five mill expansion programs have seen the initial milling rate of 7,200 MTPD escalate to the present rate of 125,000 MTPD, producing 2.5 million pounds of copper and 3,500 troy ounces of gold per day. The latest expansion, commissioned in February 1995, incorporates a 34 foot Semi- Autogenous Grinding (SAG) Mill, two 20'x30' Ball Mills, conventional roughing, cleaner column flotation, and attendant upgrades to the existing concentrate pumping and dewatering facilities. This paper will describe the SAG Plant flowsheet, and focus on the key training issues which contributed to a successful plant start-up.IntroductionP.T. Freeport Indonesia's operations in the Ertsberg mining district are located in the Jayawijaya Mountains of Irian Jaya, the easternmost province of the Republic of Indonesia. P.T. Freeport Indonesia (PTFI), the operator, is owned by Freeport MacMoRan Copper and Gold (81.3%), the Government of Indonesia (9.4%), and private Indonesian investors (9.4%). Geographical location, and sailing distances are provided on the attached location map.The operation stretches over 7 4 miles ( 114 km) from the dewatering and concentrate shipping facility at the Port of Amamapare on the Arafura Sea to the Grasberg open pit located at 3400m. The regional geology is covered in detail by Van Nort et al (1991 ), with current proven and probable reserves estimated at 1.13 billion metric tonnes grading 1.30% Copper, 1.42 ppm Gold, and 4.06 ppm Silver. The Grasberg open pit mining operation provides 92% of the mill feed, and is described in detail by Hickson (1991). The remainder of the mill feed is derived from several underground block caving operations. Current production rates provide a mine life in excess of 25 years. However, very favorable geology in the area leads to expectations that additional reserves will extend the life of the operation considerably."

Jan 1, 1996