Search Documents

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By J. Olaf Sund

"The New Brunswick gypsum and an-hydrite deposits make up part of the Windsor group in the Upper Mississippian. The present deposits were formed by surface hydration of the underlying anhydrite beds. The sub-hydrate, hydrate, and di-hydrate stages of gypsum are formed from the anhydrite by this hydration. The anhydrite was precipitated from sea water in embayments that were separated from the sea by a reef or bay-mouth bar. The anhydrite is the original form of the calcium sulphate precipitate.One gypsum deposit near Plaster Rock in northern New Brunswick was precipitated from sea water directly as gypsum, which is its present form."

Jan 1, 1960

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By Maurice Séguin

The primary aim of all ground geophysical work has been, of course, to locate orebodies. As with any geo-physical method, its success depends on a proper mastering of the types of surveys and equipment used and their application to the physical properties associated with the orebodies. The Schefferville deposits are iron ores subjected to enrichment by the process of leaching. Although some ore types are porous and low in demiity, most of the ore zones have had a net increase in density brought about by enrichment. In the course of their formation, the magnetic characteristics of the rocks have usually changed, as much of the magnetite was altered to relatively non-magnetic iron oxides and hydrous iron oxides. Ali drift-covered areas underlain with iron-formation are potential ore-producing areas. From these first two physical proper-ties and a determination of the thickness of the over-burden, a combined gravity-magnetic-seismic and/or resistivity survey allows for the detection and sorting out of iron-formation and potential ore zones from the country rocks. If the iron-formation possessed relatively uniform physical and chemical properties, the problem of locating areas underlain with ore, using geophysical methods, would be greatly simplified. Unfortunately, the iron-formation is a complex assemblage of rock types, each having different physical and chemical characteristics. In spite of this, qualitative and semi-quantitative correlation between the results of the surveys and the geology and structure of the area could be established. In addition, a semi-quantitative to quantitative correlation of the values of the residual gravity anomalies with the specific gravity, the iron content, the porosity factor, the dimensions of the under-lying orebodies and the values of the ground magnetic intensity above a reference lithologie unit, with the per cent weight Fe304 recovery and the susceptibility, led to the discovery of a direct-shipping iron ore deposit in the Schefferville mining district of Canada.

Jan 1, 1968

By M. Venkatraman

The limit of Hall - Petch relationship in ultra fine grained steels has been examined based on dislocation pile-up mechanism. When the grain size becomes small the dislocation multiplicity ceases resulting in very low work hardening rate in these materials. An approximate analysis of the theories of hardening indicates that H-P relation is obeyed up to 100nm. It appears that grain refinement is not the suggested approach to improve toughness as well as strength below a critical size.

Jan 1, 2004

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

By M. A. Power

The diamondiferous Drybones Bay kimberlite pipe is the largest pipe (900 m by 400 m) discovered to date in the Northwest Territories. The pipe intrudes granodiorite of the Archean age Defeat Pluton and contains crater, reworked crater (epiclastic) and diatreme facies kimberlite. In-situ measurements of seismic p-wave velocity were recorded with in-line refraction arrays over representative areas. Refractions from fresh kimberlite were recorded over epiclastic facies kimberlite in the eastern portion of the pipe and returned an average velocity of 4300 m/s. Refractions from weathered kimberlite were recorded on all lines and returned velocities ranging from 1900 m/s to 2200 m/s. Granite surrounding the pipe returned an average velocity of 5400 m/s. The results indicate that there is a definite contrast in seismic velocities between kimberlite and country rocks at Drybones Bay and suggest that seismic refraction surveys may be an effective means of screening kimberlite targets in glaciated areas underlain by igneous or metamorphic rocks.

Jan 1, 1998

By Ross D. Lawrence

"IntroductionOne of the methods used when applying the Market Approach to the valuation of a mineral exploration property is known as the Joint Venture Terms Method. The method is particularly useful for the valuation of early-stage exploration properties. Unfortunately, valuators are sometimes imprecise in distinguishing between joint ventures and other types of transactions.At VALMIN '94, Bob Appleyard1 proposed that, if one ignores the time value of money and the probability that the expenditure commitment would be completed, the formula to calculate the value ($V) of a property owned by Party B at the time of the deal would be:$V =$Ex (100-1%)/1% (Formula I)Where $V is the value of the property2Where $E is the expenditure commitment by Party A, andWhere 1% is the percentage property interest to be earned by party A.At PACRIM '99, Mike Lawrence and Graham Dewar3 referred to this method and suggested that there was an ambiguity in the formula proposed by Appleyard in 1994. Mike Lawrence referred to this problem again at VALMIN '014•Lawrence & Dewar suggested that the formulashould be:$V100% =($Ell%) x 100 (Formula 2)Where $V 100% is the value of the entire property,Where $E is the expenditure commitment by Party B, andWhere 1% is the percentage property interest to be earned by Party B.Subsequently, there has been considerable discussion in the AuslMM Bulletin5. In my view, this discussion has touched on a number of useful points, but generally has overlooked one essential element needed for an understanding of the correct application of the N Terms method. That essential element is to understand that there is a material difference between (1) entering into a joint venture arrangement and (2) the purchase of an interest in a property."

Jan 1, 2003

By T. G. Carter

"Damaging seismicity associated with deep faulting in both mining and civil excavations not infrequently occurs without warning, and often before proper mitigation measures have been put into place. Severe squeezing is also a common problem for excavating through deep major faults. While both problematic conditions are difficult to predict and characterize, there is often a need at pre-feasibility and feasibility level to more reliably estimate the possible level of risk posed by such geologic structures. This paper introduces some structural geologic techniques that have potential application for both mining and civil applications for aiding forewarning of the extent of these types of problem.INTRODUCTIONEncountering adverse faulting at depth in deep excavations, whether for mining or civil purposes can create serious economic and safety impacts. For deep mines or for deep tunnel projects, measures are available for aiding prediction of the extent of possible influence that large scale faults could create, but these techniques are rarely if ever applied as part of routine site investigation programs, or even as part of risk assessment evaluations. Several well established structural geologic methods of palao-history reconstruction have potential application for aiding forewarning of the extent of these types of potential problem by allowing estimates to be made of:• controlling stress orientations that might engender reactivation movement;• principal stress magnitudes that could lead to failure initiation, and• probable mechanisms of fault deformation - brittle (bursting) or plastic (squeezing).This paper explores several structural geological and rockmass characterization techniques that have application for unravelling fault structure of importance to deep engineering projects. Their application for mining or tunnelling purposes is advocated in conjunction with conventional rockmass characterization assessment approaches using GSI, RMR and/or Q to aid early recognition and definition of potential adverse ground condition behaviour associated with intersection of significant faulting at depth."

Jan 1, 2015

By Sangjian Zhang, Zhu Xiao, Lairong Xiao, Rushi Chen, Mei Fang, Zhou Li

The copper-graphite metal matrix composites were fabricated by two different production methods: directly sintering with copper and graphite (Cu-Gr composite), and in-situ sintering with cuprous copper and graphite (Cu2O-Gr composite). During the in-situ reaction sintering, a redox reaction occurs at the interface of the Cu2O particles and Gr particles, resulting in the improved physical and mechanical properties of Cu2O-Gr composites. Compared with Cu-Gr composite, Cu2O-Gr composite has a higher compression strength at any given graphite content due to the improved interface bonding and uniformly distributed fine graphite particles in the matrix. Increasing graphite content decreases the mechanical properties of the copper-graphite composites. The compression strength of Cu2O-Gr composite is 50-100 MPa higher than that of Cu-Gr composite. INTRODUCTION Copper-graphite composites have been widely used in industry due to their low density, relatively high strength and hardness, good thermal and electrical conductivity, arc ablation resistance and self- lubrication ability (Grandin & Wiklund, 2018; Han & Xu, 1999; Huang et al., 2017). Electric sliding contact friction pair in the high-speed railway system and motor brush in electric contact components have a very high demand on electrical conductivity and self-lubrication ability of materials. The electric devices need to bear both mechanical load and high electric current. Copper-graphite composites with good mechanical, electric and self-lubrication properties are the best candidates for application in multifunctional electric sliding contact frication components. The relative sliding speed of friction pair is developing towards 100 m/s or even faster, which can withstand the electric flow of more than 800 A, and it is often accompanied with vibration and impact (Guo & Ding, 2008). Conventional wear-resistant materials can no longer meet the current requirements and this promotes the development of copper- graphite composites with excellent comprehensive properties (Ding, Chen, Zhu, Zhang, & Zhou, 2009; Yasar, Canakci, & Arslan, 2007). There are many ways to fabricate copper-graphite composites, mainly including powder metallurgy method, liquid immersion infiltration method, rapid sintering method and electrodeposition method (Kalin & Poljanec, 2018; Kim, Lee, & Han, 2014; Liu et al., 2018; Wang et al., 2018). Each method has its own advantages and disadvantages, and the powder metallurgy method is the most commonly used one due to its simple process, high economic benefit, and industrial production applicability. The common steps of the powder metallurgy method are as follows (Samal, Parihar, & Chaira, 2013): firstly mixing the copper (copper alloy) powders and graphite with a certain ratio, following by die-forming, and then sintering at the high temperature with or without pressure. The advantage of copper-graphite composites is that the graphite distributed in the copper matrix uniformly and it can form a carbon diaphragm preventing the wear of the composite (Fu & He, 2010). However, the bonding strength of the interface between the copper matrix and the graphite is relative low as the combination between them is mechanical interlocking but not metallurgical bonding (Ma et al., 2008). It is meaningful to develop new fabrication technology of copper-graphite composites with better interface bonding, which could provide guidance for the design of copper-graphite composites with excellent comprehensive properties.

Jan 1, 2019

By J. Bouchard, A. Clapperton, L. Ebacher, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Froth flotation is used to produce nickel and copper concentrates. As is the case at other operations, the presence of magnesium is detrimental to the flotation products. In the past year, the exploitation of a new deposit has increased magnesium in the feed. Thus, it has been challenging to meet the required ratio in the final nickel concentrate. In search for a consistent solution for this problematic, an empirical flotation simulator making use of selectivity curves was developed. The circuit was expressed as a system of linear equations, which considered the distribution of copper, nickel and gangue minerals in the different streams. The relative quantities of each mineral are given by the separation efficiency curves of the various banks in the circuit. Three sources of data were used to calibrate the simulator: historical plant data (metallurgical balance), infinite dilution bench-scale flotation tests, and direct sampling of flotation cells. The calibrated separation curves were used to predict the recovery of the different species based on a single mineral recovery. Validation of the simulator showed good fit for the valuable minerals. The simulator was then used to infer the optimal operating conditions of the flotation circuit to optimise magnesium oxide content of the nickel concentrate. Simulation of two re-arrangements of the circuit gave a promising solution with a Fe:MgO ratio 2.42 times higher than the minimum value.INTRODUCTION Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Figure 1 shows the location of the mine site. After crushing and grinding, froth flotation is used to produce nickel and copper concentrates. The flotation circuit is designed with multiple stages consisting of bulk copper/nickel flotation, copper/nickel separation, and a separate nickel circuit (bulk float and cleaning)."

Jan 1, 2018

By Raymond Dallaire

The Humphrey&apos;s spiral is a static gravity separation device which cannot be adjusted to match short-term variations that occur in the feed. Any disturbance in the feed grade, per cent solids or flow rate affects substantially the recovery and grade of concentrate. Such variations must be minimized in order to maintain the desired rate of production and quality of the product for which the installation has been designed. A study has been performed in which the foregoing assertions were quantified. The feed grade, per cent solids, flow rate and particle size were varied independently. Ore from Carol Lake, Nfld., was used throughout the experiments. This consisted of specular hematite and magnetite in a silica gangue.

Jan 1, 1978

By J. A. Pigott, R J. Hall

The International Nickel Company of Canada, Limited operates five underground mines on the rim of the Sudbury Basin in the northern part of the Province of Ontario. Four of the mines, the Frood-Stobie, Creigh-ton, Murray and Garson, are located on the south range of the basin with-in a radius of IO miles of the centre of the city of Sudbury. The fifth mine, Levack, is on the north range about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite and pyrrhotite. In 1960 the total ore production was in excess of 16 mil-lion tons, 95 per cent of which was produced from the five underground mines and the balance from the Frood-Stobie Open Pit. Mining at this open pit is nearing completion and underground production has been expanded to replace the open pit tonnage.

Jan 1, 1961

By M. J. Collins

The Advocate Mines Limited asbestos property is 6 km north of Baie Ve rte on the northeast coast of Newfoundland. Mining began in the early 1960s and was concluded in 1981. The chrysotile asbestos deposit lies at the north end of the Baie Verte Lineament, the interface between a closing ocean floor and continental margin. Asbestos occurs within ultramafic rocks of abducted ophiolite massifs that were thrust westward against Fleur-de-Lys Supergroup metasediments (continental rise sediments) in the Lower to Middle Ordovician. The asbestos-bearing ultramafics belong to the Central Ultrabasic Sequence of the Advocate Complex. Serpentinized peridotite of this sequence has a 'waste cap' core that grades outward to increasingly sheared rock. Asbestos is found mainly in a northtrending, basin-shaped zone surrounding the core, specifically within fractured serpentinized peridotite that abuts the sheared rock. Asbestos appears as stockworks of chrysotile cross fibre veins and is concentrated between brown, narrow brucitic dunite dykes and sills. Shear contacts commonly surround the ultrabasic body. Cross faults and complex Jointing also exist. The Advocate Mines Limited mill produced 65,000 tonnes of Group IV fibres and 1 l , 000 tonnes of Group VJ fibres annually. The bagged product enjoyed markets worldwide.

Jan 1, 1984

By M. G. Manzone

Approximately two-thirds of the annual 210,000 tons at copper refined by AMAX Inc. at the United States Metals Refining Company in Carteret, New Jersey, comes from a wide variety of copper scrap ranging from low-grade smelter scrap to wirebar-grade material. The equipment and methods used to effect such large-scale metal recycling in an urban area and the measures taken to collect and recover metal values from smelter and refinery byproducts while protecting the environment from pollution are described and discussed.

Jan 1, 1977

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017

By Witold J. S. Ostrowski

Stabilization of water-bearing sediments by the freezing method for shaft sinking has been used for over 80 years on the European Continent. The real application of this method in Canada started with the development of the potash mines in Saskatchewan during the past fifteen years. The great depth to which it is applied creates a number of problems which have to be seriously considered by engineers in order to produce a safe and economical design. Freezing depth, thickness of the ice wall, number of the freeze holes, capacity of the freezing plant, pre-freezing time, etc., are the most important points which have to be established. Recent field experience in freezing to great depth in the Saskatchewan area is immensely interesting and important for further development of our potash mining and the application of the freezing method.

Jan 1, 1967

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By T. Verdel, Y. Gunzburger

Rockfalls are major and essentially unpredictable sources of danger, particularly along transportation routes (roads and railways). Thus, the assessment of their probability of occurrence is a major challenge for risk management. From a qualitative perspective, it is known that rockfalls occur mainly during periods of rain, snowmelt, or freeze-thaw. Nevertheless, from a quantitative perspective, these generally assumed correlations between rockfalls and their possible meteorological triggering events are often difficult to identify because i) rockfalls are too rare for the use of classical statistical analysis techniques and ii) all intensities of triggering factors do not have the same probability. In this study, we propose a new approach to investigate the correlation of rockfalls with rain, freezing periods, and strong temperature variations. This approach is tested on three French rockfall databases, the first of which exhibits an outstandingly high frequency of rockfalls (approximately 950 events over 11 years), whereas the other two databases are more typical (approximately 140 events over 11 years). These databases come from (1) the national highway RN1 on La Réunion Island, (2) a railway in the Bourgogne-Franche Comté region, and (3) a railway in the Auvergne region. Whereas a basic correlation analysis is only able to highlight an already obvious correlation in the case of the “rich” database, the newly suggested method appears to detect correlations even in the “poor” ones. Indeed, the use of this method confirms the positive correlation between rainfalls and rockfalls on La Réunion Island database. This method highlights a correlation between cumulative rainfalls and rockfalls in the Bourgogne region, and it detects a correlation between the daily minimum temperature and rockfalls in the Auvergne region. This new approach is easy to use and also serves to determine the conditional probability of rockfall function of a given meteorological factor. This approach will help to optimize risk management in the studied areas based on their meteorological conditions. Nevertheless, even if some rockfalls are correlated to meteorological factors, other seems to occur independently of these factors, which highlights the unpredictability of rockfall hazard.

Jan 1, 2015

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005