Search Documents

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990's and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By J .. Carignan, Y. Dembele, J .. Guha, A. Fowler, A. Gobeil

The Barlow Lake stratigraphic section comprises the top of the Gilman Formation, the Blondeau Formation and the three sills of the Cummings Complex. Representative samples were analysed to allow characterization of the chemo-stratigraphic profile and geochemical affinity of the six rock facies found in the section. All the mineralized horizons are associated with sedimentary units. Geochemical signatures associated with the mineralizations are either very weak or very localized and shown by increases in K20 around the mineralizations and Fe203 near them. The mineralizations are stratiform, synvolcanic but resedimented and remobilized by regional metamorphism and possibly by hydrothermal activity initiated by the intrusion of the Cummings Complex. The evolution of the sedimentary basin with the decrease of its depth is confirmed by the chemo-stratigraphic profiles. Stratigraphic position in the section is important in order that the chemo-stratigraphy may serve as a guide for mining exploration in the distal facies of the Blondeau Formation.

Jan 1, 1984

By S. Dessureault

The relatively recent explosion of available data in all business sectors has induced a common expression of “drowning in data, starving for information.” The mining sector is affected by the information age through equipment-based sensors, process monitoring, and traditional enterprise data sources. Information technologists have developed techniques such as data mining that apply new and old statistical algorithms to large datasets. Mine planners and managers can apply these tools for improved planning and control, thereby increasing the use of the highly underutilized information system infrastructure in most modern mines. This paper describes the use of data mining and its enabling technology, data warehousing, in the development of an energy consumption model for large surface mines using real historical data.

Jan 1, 2007

By E. Y. Dougherty

Introduction As practised during the last two years at the Vipond Consolidated gold mine, mining geology has meant the application of geology to the problem of finding, developing, and mining ore. This article reviews the results attained in Vipond mining geology as thus defined. Most effort was directed toward clarifying and interpreting the tangible physical causes of vein and ore localizations, and in the following pages these questions are dealt with in considerable detail. Discernment of the influence of rock folding and deformation on the localization of veins, and of the influence of certain structures and rocks in or near carbonaceous zones on the localization of ore-bodies, have been the main practical results of the studies. Consideration of some of the geological features of the Porcupine area, and of the geology and mining experience of the principal producing mines, has helped toward a perspective of Vipond's ore-finding problems. These features are first discussed. The background and procedure for Vipond mining geology, and the major results of the geological mapping, are then summarized. Then follows a résumé of tangible factors that influenced vein, ore-body, and gold localizations; and, next, explanations of the facts ascertained. Because they were found of little utility, many fascinating problems, such as the origin and mode of emplacement of the veins and lodes(l), the ultimate source of the ore, and the physico-chemical and mechanical agencies affecting vein and ore formation, are treated cursorily or are neglected in these notes.

Jan 1, 1934

By Colin Harvey

The paper industry in the Pacific Northwest is a potentially large market for industrial clays. Current trends within the paper industry towards higher quality newsprint, filled and coated papers, offers an incentive for exploration in the region since the current supply of kaolin is mainly from Georgia in the southeastern U.S. Freight rates commonly exceed US$100 per tonne. The kaolin resources of the Pacific Northwest require expensive processing technologies to meet the industry specifications and it is doubtful that any large development of the local resources can be supported at the present time. Competition from high-quality regional resources of carbonates is another factor weighing against the development of local kaolin resources while there is a potential threat from shipments ofAsian and Brazilian kaolin in the early part of the 21st century.

Jan 1, 2001

By M. W. Grabinsky, P. B. Tomory, J. Carvalho, J. H. Curran

Many underground mining operations use Split Set friction stabilizer bolts for rock support. Currently, however, little has been done to quantify the effects of various rock mechanics and operational parameters on the capacity of frictional support systems. The strength of Split Sets is usually measured by means of a pull test wherein a jacking force is applied to the bolt and a slip load is obtained. In order to evolve a rational design procedure for this type of support, an extensive database of over 900 pull test results from more than 50 mines through- out North America has been assembled and analyzed. Associated relevant rock mechanics parameters (rock type and quality) and operational details (drilling method, bit size, drive time, time to pull test) were also obtained, as completely as possible, for each test. Analysis of the information has yielded several charts that relate pull-out strength to relevant parameters and simple statistical analyses were conducted where necessary. Quantified distributions for pull-out strength were also produced for several operating conditions. The factors that most significantly affect bolt strength have been identified and specific applications to design are discussed. The information presented will assist mining engineers in designing safer and more economic support using Split Sets.

Jan 1, 1998

By C. S. Gibson

INTRODUCTION I WELCOME the opportunity to speak on Programmes in Safety. The invitation to do so shows that those guiding affairs of the Institute in this District realize the practical importance of this subject. My remarks are intended primarily for mines having 100 to 400 employees, approximately. With minor modifications, however, they apply also to larger or smaller operations. Others, I hope, will derive benefit from this paper, for they, too, have a part to play in accident prevention; for example, contractors such as shaft-sinkers; manufacturers of equipment; and consultants and designers of mining, milling, and metallurgical methods. These troubled times stress, as never before, the importance of efficient operations in mining. The days are gone when neglect can be afforded. Safe working conditions and satisfied employees are essential for efficient production at reasonable cost. The mining industry of Ontario long has been keenly aware of the human aspects of this subject, and as a whole it has done much to decrease the frequency and severity of disabling accidents. The number of fatalities per 1,000 employees has been reduced from a high of 5 some two decades ago to an all-time low of 0.89 in 1948; the incidence was slightly higher in 1949, being 1.17 per 1,000. The reduction in non-fatal compensable accidents also has been outstanding, frequency having ?been reduced from over 200 per 1,000 employees some two decades ago to 54 per 1,000 at the producing mines in 1949. These statistics demonstrate progress. Nevertheless, the general picture still leaves much to be desired when viewed from two other angles.

Jan 1, 1951

By G M. Thorpe

This paper discusses mine research at Inco, giving specific examples of research projects which illustrate the approach to mining problems. The first example covers the development of a new mining method, "undercut and fill," which was originated for mining badly broken-up pillars, but which is now rapidly replacing the square set method of pillar recovery. In the new method, ore is extracted in a series of successive horizontal cuts, progressing downward, a cut being completely mined and filled before the cut below is started. In the second example, improvements to the "cut and fill" method of mining are discussed. These improvements are the result of improved techniques and improved equipment, etc., with, in many cases, the former being made possible by the latter. The advances made have permitted the use of the "cut and fill" method at much greater depths than before. The third example is presented to illustrate research undertaken to obtain the earliest maximum advantage of the introduction of a new piece of equipment or material. For this purpose, the development of the "Under-ground use of AN /FO Blasting Agent " has been selected. Work on this project started in May, 1960, at a time when there was very little in-formation regarding the potentialities of AN /FO for underground blasting, either primary or secondary. By the end of 1961, AN /FO made up 64 per cent of the explosives used under-ground at Inco mines.

Jan 1, 1963

By J. Keith Haddock

"IntroductionThe Bienfait Mine is operated by Bienfait Coal Company Ltd., one of the Luscar Limited group of companies. Situated 5 km southeast of the town of Bienfait, Saskatchewan, it can produce 2.0 million tonnes of lignite annually in addition to 158,000 tonnes of char from a carbonization plant located on the property. Geology The economically mineable coal seams of the Estevan area are found in the Ravenscrag Formation. The lignite-bearing sands, silts and clays were deposited in Early Tertiary age, in an inland sea centred in the Williston Basin of North Dakota. The top of the Ravenscrag is an erosional surface, overlain by Tertiary or Quarternary sands and gravels or glacial till. The regional structure is a gently plunging syncline which dips to the southeast at about 0.3 degrees. There are minor undulations in the Bienfait area which are due to differential subsidence during deposition. Sporadic faulting is probably a result of glacial pressures, and preglacial and glacial channels are responsible for washout zones and the abrupt irregular subcrop found in the area. There are two economic coal seams in the Bienfait area, an uppe; seam locally known as the Roche Percee, and a lower seam, the Estevan. Both seams have been extensively mined since lignite mining began in the area in the late 1800s. The Roche Percee remains only in a small portion of the Bienfait Mine and comprises a very minor portion of the reserves. It averages 1.74 m thick under 8.1 m of overburden. The till rests on top of the Roche Percee and due to weathering the seam is generally of poorer quality. The Estevan seam comprises the majority of reserves at Bienfait. The main seam which is being worked on consists of an upper bench averaging 2.75 m, a carbonaceous parting of 0.21 m, and a lower bench of 0.92 m. Overburden depth above this seam varies from 21.0 m to 38.0 m."

Jan 1, 1985

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By M. Djivre, T. Eger, A. Godwin, I. Bhattacherya

Load-haul-dump vehicles (LHDs) are extensively used in underground mining, however, equipment design and operating conditions contribute to restricted operator sight lines. The inability to clearly see people, objects, or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, line-of-sight assessments are traditionally completed in the field. However, field methods are unable to evaluate lineof- sight under dynamic operating conditions, and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height. Results of this research show computer simulation and virtual reality can be successfully used to evaluate line-of-sight during the operation of LHD vehicles. In order to benefit from virtual reality applications, the work environment, LHD vehicle, and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic analysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHDs were developed from manufacturer specifications and pictures taken from LHDs currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle, and the vehicle and human were driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired line-of-sight were successfully identified with this method. The JACK program could also provide real-time feedback on the human’s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHDs evaluated in the JACK software package can also be combined with mine models and imported into other VR software packages (e.g. Blender) in order to enable viewing in Laurentian University’s Virtual Reality Laboratory. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial vision issues.

Jan 1, 2005

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, R. Pérez-Garibay, C. Jimenez-Velasco

A current problem in gold production is the presence of copper minerals which dissolve during conventional cyanidation practice. The dissolved copper causes several problems in the different stages of the process. This issue is the base for copper elimination/recovery methods such as the Sulphidization, Acidification, Recycling, and Thickening (SART) process, which is currently used in gold production plants around the world. Even though the process is well established, new challenges appear as the composition of the solution varies from ore to ore, in some circumstances affecting the performance of the SART process. This work presents a thermodynamic study and experimental tests performed to understand the role of the initial copper concentration and sulfur addition, on the efficiency of the copper removal. For a constant cyanide concentration, an increase in the initial copper concentration causes a decrease in copper removal; high sulfur/copper molar ratios favor copper removal. We demonstrated that the cuprous sulfide formed from solutions with high ionic strength, presents better sedimentation rates than solutions with less ionic strength. For solutions with low sedimentation rates, the use of some pretreatment is necessary to facilitate the sedimentation such as addition of flocculants, particle recirculation and the used ultrasonic pretreatment.

Jan 1, 2014

By N. A. P. Kiran Kumar

The Zr-Nb alloys are reported to be showing superior resistance to corrosion and substantially lower hydrogen pickup when compared with zircaloys. In the present study zircaloy-4 and Zr-1Nb (E110) alloys were hydride using high pressure hydrogen gas furnace at a pressure of 20 MPa. Thermal cycling was done on the samples at a temperature of 3500C for 10 cycles with 5h soaking time at 3500C per each cycle. The Microstructural observations on zircaloy-4 samples show long and interlinked hydride like chain, oriented along the circumferential direction. Whereas in Zr-1Nb, short hydrides were observed with hydride platelets not showing interlinked chain like structure. The hydrides in Zr-1Nb were observed to be not showing particularly orientation along the circumferential directions. Electron backscatter diffraction was use to understand the hydride precipitation and their orientation in Zircaloy-4 and E110 alloy.

Aug 1, 2010

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By J. Holtzhausen

"An analysis of operating costs for underground mining operations in the current global economic climate considers the financial burden for a ventilation system to be in vicinity of 30–50%. These operating costs are often overlooked by management teams in the greater scale of things when looking to save money in the procurement phase. This oversight to operational costs can be as little as the effective delivery of ventilating air to the work zone. One of the biggest opportunities for substantial savings and improvements can be realized in the selection of a quality vent duct that is suitable and fit for purpose. The key component to the selection process for quality products is a solid selection criterion that is followed during the tender process. This allows the management team to filter out unsuitable suppliers and products. The case study identifies some of the key components that were considered in the procurement and selection process for lay-flat ducting products. These included the characteristics and strength of the materials. The selection criteria also considered a ducted performance comparison that offers the best aerodynamic performance with some of the following components. • Airflow at Duct Face (m³/s or cfm), Fan Pressure (Pa), Air Power (kW or hp), Assumed Fan Efficiency, Annual Running Costs, K – Factor or Lambda, Leakage Factor, Joining Method and available Duct Lengths with weights. • Critical components considered were the current Testing standards available for: o Bursting Strength AS 4878.5, Mass AS 2001.2.13, Tensile Strength AS 4878.6, Tensile Strength AS 2001.2.3.1, Tear Strength AS 2001.2.10, Tear Strength AS 4878.7 • Other key considerations were: o Warranty Claim, Damage claims, Local storage / operations, community engagement and relationships, current testing data, previous issues, after sales service with technical assistance, etc. Hidden costs associated with product failures and operational stoppages are often not quantified during the tender process. Buyer beware. INTRODUCTION The largest constraint underground mining operations currently face are their operating efficiencies and electrical costs. The overall cost of an operations ventilation system and its components requires more focus to identify what opportunities exist to maximise efficiency and effectiveness. This tender process may not always be clearly understood and it should be broken down into fewer components to achieve quantifiable results."

Jan 1, 2019

By A. J. MacEachen

"LIKE ALL OTHER NOVA SCOTIANS, I have been thrilled during the past few years with the growing evidence that substantial reserves of oil and gas are being discovered off the Atlantic coast of Canada. There are those in this province who believe that large-scale commercial production is just around the corner, and that when it starts Nova Scotia will begin to float on a sea of royalties. These overly optimistic people, of whom I am not one, are convinced that with the first barrel of oil shipped to market, Nova Scotia can forget its financial problems while its people take on the luxurious lifestyle of the shieks of Kuwait or Saudi Arabia. You and I know, however, that even though offshore oil and gas may turn out to be the greatest gift nature has ever bestowed on Eastern Canada, it may take some considerable time before the reserves can be accurately assessed, before the industry can become fully operational, and before the benefits of production can be translated into royalties and tax revenue, improved public services, new industrial facilities and more jobs. While it is premature for the ordinary Nova Scotian to take on the habit of buying expensive cigars and lighting them with ten-dollar bills, it is not too early for him to insist that governments and industry plan intensively and well for the beneficial exploitation of undersea resources."

Jan 1, 1973