Search Documents

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

By Derek H. C. Wilton, David T. W. Evans

"Abstract - The Midas Pond gold prospect, central Newfoundland, is hosted by sheared and altered felsic and mafic pyroclastic rocks of the Tulks Hill volcanics, Victoria Lake Group, and has been trenched and tested by 19 diamond-drill holes. Gold values are sporadic, with the best diamond-drill intersection assaying 7.3 g/t over 0.9 m, and the highest grade channel sample containing 14.7 g/t over 1.15 m. Alteration and mineralization are confined to a 200 m wide brittle-ductile shear zone. This shear zone formed in response to regional D1 deformation, and the shear zone fabric parallels the regional S1 foliation. D2 deformation resulted in broad Z-shaped flexuring of the shear zone. The deformation was probably related to the ca. 396 Ma to 420 Ma Salinic Orogeny.Advanced argillic alteration and an extensive halo of Fe-carbonate and pyrite surround the gold mineralization. Alteration minerals include pyrophyllite, paragonite, quartz, plagioclase, chlorite, fluorite, Fe-carbonate, and pyrite. As such, the alteration seems to reflect combined epithermal (argillic) and mesothermal (carbonate) mineralizing environments. The argillic alteration and fluorite represent a regional hydrothermal effect on the felsic volcanic rocks; whereas, the Fe-carbonate and pyrite represent a mesothermal alteration associated with auriferous quartz veins. The Au, which is spatially associated with pyrite, occurs in three structurally-controlled vein sets. These veins are confined to the contact between a highly deformed breccia (the banded mafic tuff) and structurally overlying, altered felsic tuffaceous rocks. The vein sets include: V1 boudinage veins that parallel the shear-zone fabric (C-shear veins), and V2 and V3 extensional fracture veins which are controlled by an S2 fracture cleavage. V1 veins are the earliest and contain the lowest concentrations of Au. V2 and V3 veins are concentrated within the hinges of the D2 flexures.Pb isotope data for galena separates indicate that the Pb in the vein systems was probably of local derivation. Sulfur, C, and O isotope data for mineral separates are similar to data for typical mesothermal lode gold deposits. Fluid inclusion data suggest the presence of at least three hydrothermal fluid types in the region, viz., (1) an early saline fluid which produced the argillic alteration, (2) a CO2-bearing fluid directly related to the auriferous mineralization, and (3) H2O-NaCl fluids which flowed through the Midas Pond shear zone at a lateral distance from the zone of mineralization. The mineralizing fluids are interpreted to have been CO3 -2-rich types which originated through metamorphic dehydration and decarbonation of mixed island-arc and continental crustal rocks. Gold precipitation resulted from the reaction of these fluids with the Fe-rich breccia unit. Pre-existing and simultaneously crystallizing pyrite served as loci for Au precipitation."

Jan 1, 2000

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980

By Leslie F. Sawatsky

Each potential oil sands developer deals with the question of optional sources of raw water to supply large water demands that range from 50 to 80 million cubic metres per year for each of six existing and planned developments. The Athabasca River currently supplies nearly all of the water to the existing mines via conventional bank intakes, which has resulted in some concern over the effects of reduced river flows. This paper describes the various water supply options, and the likely scenario for future oil sands water supply projects. Various water supply options have been suggested including Athabasca River water via infiltration galleries, groundwater, combined Athabasca River water and alluvial groundwater using wells (i.e. bank filtration systems), diversion of tributary rivers, utilization of large lakes in the region and pumping from other large rivers in the region. Investigations show that the size of river catchment needed to support raw water usage by a typical oil sands mines exceeds 5,000 km2 eliminating all tributary rivers that are located in the oil sands region except those rivers with large drainage areas like Firebag and MacKay Rivers. Lakes cannot be used as a source of supply due to large water deficits for smaller lakes and the large cost of sourcing water from a lake as large as Lake Athabasca. A groundwater source alone would not likely meet the large water demands. River intakes on the Athabasca River will likely continue to be the most practical water supply option for oil sands mines north of Fort McMurray, although various types of Athabasca River intakes are possible. Existing intake systems include screened riverbank intakes, forebay intakes, and river bottom intakes. Infiltration galleries are not feasible for most sites, though some bank-filtration-type systems using high capacity wells may be an option if there is sufficient thickness of high-permeability alluvium at a suitable location in the Athabasca River valley.

May 1, 2004

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By B. J. Clauzier

"The Falconbridge Limited approach to employing communication equipment is first, to determine what is required in a given situation, second, to evaluate the possible alternatives, third, to select the most suitable hardware and, fourth, to determine what modifications, if any, are required to ensure not only successful implementation but continued low-cost reliability. Two examples are examined.The first situation required remote video monitoring of an acid loadout station. Several alternatives for linking to theremote site were investigated, including hard-wired, slow-scan and microwave. A comparison of these alternatives is shown and an appraisal of the performance of the selected microwave link is presented.The second situation required direct voice contact between the two members of an underground tram crew. Alternative solutions are described and an evaluation of the selected system- SHF portable radios - is presented.ObjectivesIn general, projects must have four main objectives: (1) to improve the safety of its operations; (2) to reduce its operating and capital costs; (3) to increase the efficiency of its work force; and (4) to increase its productivity. ScopeCommunication, when used wisely, can be a good tool to achieve these objectives. Projects can be kept simple using existing technology and adapting it to a particular task. To ensure the success of the project, it was necessary: to determine the project objectives; to evaluate the possible alternatives; to select the most suitable hardware; to adapt the hardware to the application, if required; and not to provide more than is necessary.Application at FalconbridgeTo illustrate this approach, two examples of actual installations at the Sudbury Operations are presented, sulphuric acid loadout, and the Falconbridge Mine haulage system."

Jan 1, 1987