Search Documents

By I Treloar, T Elenbaas, E Isaaks

Critical reviews of grade control generally focus on blasthole sampling and the estimation of ore control block model (OCM) grades, with little or no attention given to dig-line design. For example, the estimation of block grades is deemed important as estimation errors lead to the misclassification of ore types and subsequent dollar loss. Recognition of the problem that the underestimation of block grades may be more or less costly than overestimation led to the application of loss functions to the classification of individual OCM blocks by ore type. The method is known as maximum profit selection (MPS). However, each OCM block may be misclassified a second time by dig-line design. Although each block may initially be assigned an optimum ore type by MPS, OCM blocks are seldom individually mineable by ore type. As a result, a common solution to this problem is the design of mineable polygons or dig lines loosely constrained by a minimum mining width. All material within a properly designed dig-line polygon can be mined and sent to a single destination such as the mill, stockpile or waste dump. These dig lines are often designed manually or by simple variations of computer-generated contour lines. They are generally suboptimal and result in additional misclassifications of ore types. This paper provides an algorithm for constrained optimum dig-line design where dig-line misclassifications are also evaluated through loss functions or MPS. Constrained optimum dig-line designs minimise the dollars lost by dig line misclassifications for a given minimum mining width constraint. A case study is provided illustrating constrained optimum dig-line design and subsequent benefits.CITATION:Isaaks, E, Treloar, I and Elenbaas, T, 2014. Optimum dig lines for open pit grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 425–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D A. Williams, P J. Chapman

Constructing upstream raises with tailings is an accepted and cost-effective practice in Western Australia, where the climatic conditions are favourable, desiccation (and hence overconsolidation) occurs rapidly due to air drying and there is a perceived low seismic risk. This is in contrast to many other settings, where there is either a positive water balance, high seismicity or a combination of both. In recent times, there has been an increased focus on seismicity in areas of Australia that have historically been considered to be of low seismic risk. The increased focus is driven by two recently published documents used by tailings practitioners and increased awareness from corporate entities, particularly those with mines in high-seismicity regions such as South-East Asia and South America (particularly Chile).The increased awareness has resulted in increased rigour being applied to seismic design of tailings storage facilities (TSFs) in general, and particularly upstream-raised TSFs. This paper compares the results of a seismic stability assessment for an upstream-raised TSF located in the Goldfields region of Western Australia, which has historically been considered a low seismic area, with a seismic stability assessment carried out for a crossvalley TSF containing similar tailings but located in a high-rainfall, high-seismic setting in South-East Asia. The influence of the adopted design earthquake values on the results of the assessments and the potential impact of the maximum design earthquake (MDE) on the design approach is presented for both cases. The results indicate that although the Western Australian site is located in an area thought to have low seismic risk, the screening level analyses suggest that the MDE could result in liquefaction of the tailings materials. Not surprisingly, liquefaction was also indicated for the South-East Asian site. The outcomes of the assessment are also presented.CITATION:Chapman, P J and Williams, D A, 2015. Seismic design of upstream-raised tailings storage facilities in a semi-arid, low-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 157–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By B Taylor

Although the underground mining environment is arguably safer now than at any time in history, as underground mining operations across the globe increase in-depth, magnitude, and complexity, protecting workers from harm becomes increasingly challenging. In deep, stressed, seismic mines the development face is one of the most hazardous work areas. The active face is usually the furthest extent of the underground workings, so ventilation can be difficult to maintain, exposing workers to high temperature and humidity while working on foot and doing manual labour. While mechanisation has made many tasks easier in modern times, the reality of underground mining is that development charge-up workers still spend long periods directly exposed hazards at the face. In 2019, Orica and Epiroc partnered to co-develop the world’s first fully mechanised development charging unit using fully wireless initiation, called Avatel™. Built on Epiroc’s M2 Boomer carrier platform, the system is designed to allow one person to charge a development face from the safety of a fully enclosed cabin, thereby reducing exposure to hazards at the face. The system was prototyped in Europe before entering commercial introduction in 2022. This paper reviews earlier attempts to mechanise underground charge-up and describes the development journey and engineering challenges of building a mechanised development charging machine.

Mar 29, 2023

By D Felipe, G J. Harbort

In the past 40 years substantial changes have occurred in flotation machines. This has included increases in mechanical cell size to 630 m3 , significant changes to flotation column aeration design and widespread use of the Jameson cell and other pneumatic flotation cells. Over the corresponding period there has been increased used of machine characterisation measurements to benchmark and optimise flotation circuit performance. JKTech maintains a database of industrial flotation machine characterisation measurements. The database contains over 4000 entries and includes gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity, cell dimensions and impeller tip speeds. Data comes from numerous operating sites and commodity groups, including gold, copper, molybdenum, nickel, palladium, lead-zinc, platinum, silica, phosphate, coal and iron ore. Flotation duties registered include flash flotation, preflotation, roughing, scavenging and cleaner circuits. Measurements have been conducted on a wide range of flotation machines from different manufacturers. This includes forced air machines, such as Outotec and Dorr Oliver, and self-aerated machines, such as Denver and Wemco. The database also includes substantial flotation column entries, such as the Microcel, Eriez/CMT Slamjet and Jameson cell. This paper describes the flotation machine characterisation database and discusses the variation between different types of industrial flotation machines, in operating production circuits.

Aug 24, 2022

By D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of a gangue mineral grade limits by the concentrator may also result in significant penalties. Online grade analysers which can provide reliable real-time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades. MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at a nickel concentrator plant. The project initially focused on stabilising the final concentrate grade without directly accounting for nickel recovery. The site later procured additional Blue Cube MQi analysers, resulting in the expansion of the FloatStar Grade-Recovery Optimiser to incorporate recovery component in the performance. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser.CITATION:Mantsho, S M, Phillpotts, D and Strobos, P, 2012. The implementation of FloatStar grade-recovery optimisation control solutions using Blue Cube online grade analysers on industrial flotation circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Wright JK, Turner RE, Batterham RJ, Morrison AL

Simulation can play an important role in the design, optimization and control of complete industrial processes, the most appropriate method depending on the particular application. Most commonly, process models or simulators are means of representing the process which are either purely mathematical or physical. Mathematical models, however, almost invariably need to be based to some extent on experimental data or require experimental verification before they can be used with confidence. Ways in which experimental and mathematical modelling techniques can be combined to best effect are discussed, with reference to the simulation of iron ore induration and direct reduction processes. A novel method is presented for the simulation of direct reduction shaft furnaces. Small scale apparatus has been developed in which ore or pellet samples are subjected to the changing environment of the industrial process. The time dependent conditions (solid temperature and gas compositions) are provided by a mathematical representation of heat transfer and the conservation of mass and energy in the process Simulated.

Jan 1, 1986

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

By J L. Macdonald, G S. King

"The development of a predictive geometallurgical model is a multidisciplinary and iterative task that involves both discovery and integration aspects. In this paper, the authors discuss the concepts of geometallurgical modelling in terms of the underlying relationships that are used to connect geology, metallurgy and economic value, and how the early-stage preparation of a spatial geometallurgical model enhances project value and provides a sound basis for future studies and test work programs.Hot Chili’s (copper-gold-molybdenum) Productora Project, which is located in northern Chile, is a porphyry-copper style deposit that can be exploited using open pit mining and preparation of a saleable concentrate from fresh ore, as well as heap leaching, solvent extraction and electrowinning (SX-EW) extraction of copper from oxide ores. To enhance project value in the Productora prefeasibility study (PFS), Hot Chili developed a geometallurgical model that was used to predict the process responses of both sulfide and oxide ores. The Productora model incorporates test results from mineralogical, metallurgical and comminution testing, as well as other studies completed on a suite of samples collected from the many geological domains of the deposit.Using Bond Work Index and Abrasion Index proxies in the geometallurgical model, Hot Chili estimated the variability of sulfide ore throughput and comminution costs. Heap leach acid consumption in oxide ore was estimated from drill hole calcium concentrations. The model was then used in mine scheduling to identify high and low throughput or high and low acid ore zones so that the processing of these zones could be advanced or deferred to improve net present value (NPV). Additionally, the cost benefits of preparing an early-stage geometallurgy model were quantified through a comparison to a conventional model that was based on test work averages.CITATION:King, G S and Macdonald, J L, 2016. The Business Case for Early-stage Implementation of Geometallurgy– an Example from the Productora Cu-Mo-Au Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 125–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A G. L Pratt

Inclined troughed belt conveyors are more frequently being selected from a range of alternatives, which include shafts and trucks for ore haulage in underground mass mining projects. Belt conveyor haulage systems are being operated with lifts exceeding those normally associated with truck haulage systems and approaching the limits of shaft haulage systems. A belt conveyor haulage system, in this context, incorporates subsystems for: crushing,tramp detection and removal, andhaulage. This paper presents details of recent inclined troughed belt conveyor systems for underground mining operations, and explores the application of inclined troughed belt conveyors for the increasing demands of future underground mass mining projects.

Jan 1, 2008

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

The Mt Keith Mining Alliance operates a fleet of large capacity hydraulic face shovels and more than 40 X 240 t capacity haul trucks to deliver annual production in excess of 40 Mbcm per annum. The Mt Keith Nickel mine is currently operating at a depth to 300 m below surface with a planned final depth of the order of 500 m. As is the case with any large open pit managing the health of the workforce on continuous shift operations is of critical importance to achieving outstanding safety and production outcomes. Fatigue management at Mt Keith is effectively managed by the personnel operating the mining equipment, with assistance and understanding of the management team and supervisors. The program has been driven through the introduction of Fatigue Champions and a comprehensive management plan that includes education, individual health plans and the use of new technologies. Mt Keith has been instrumental in trialling new technology which assists in monitoring fatigue in operations personnel. Insight into these developments is provided in the context of the overall fatigue management plan. The field trials of the OptAlert(TM) system and how it assists in measuring fatigue is explained. The implications for individual operators and the context for a fleet wide approach to fatigue management is also discussed. Mt Keith has recently completed the second phase of trials with the result that this new and exciting technology is being considered for adoption globally across BHP BillitonÆs open pit mining operations.

Jan 1, 2007

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Li, H Jinto, M Laxman

The behaviour of tailings under cyclic loading has an impact on the stability and deformation of tailings dams and a good understanding of the cyclic behaviour of the tailings under earthquakes is important for tailings engineers and tailings operators for the design and safe operation of tailings dams. This paper presents an investigation into the cyclic behaviour of tailings using both laboratory cyclic direct simple shear (DSS) testing and numerical modelling. The laboratory testing involved cyclic DSS tests on gold tailings and zinc-copper tailings under different loadings and loading frequencies. The gold tailings specimen tested at a higher loading frequency and a higher cyclic stress ratio experienced spontaneous liquefaction during cyclic shearing and the zinc-copper tailings specimen tested at a lower loading frequency and a similar cyclic stress ratio exhibited ductile behaviour and liquefied due to cyclic mobility. The liquefaction behaviour of the tailings was modelled using an advanced constitutive model (UBCSAND), which was developed specifically to model soil liquefaction and strain softening under cyclic loading. The constitutive soil model presents the nonlinear soil behaviour under dynamic loading using a hyperbolic stress-strain relation. Dynamic analyses were carried out using a finite difference program FLAC. The cyclic stress-induced excess pore water pressures measured in the laboratory were modelled using numerical simulations of the laboratory tests under different loading conditions. The results of the non-linear dynamic analyses demonstrated the capability of numerical modelling of cyclic shearing induced excess pore water pressure and the onset of the spontaneous liquefaction. The laboratory investigation and numerical modelling technique provided the key properties and parameters for the dynamic analyses to assess the stability and deformation of tailings dams under design earthquake events. More importantly, the laboratory tests and numerical modelling provided some insights into liquefaction behaviour of the tailings during earthquakes. CITATION:Li, A, Laxman, M and Jinto, H, 2018. Liquefaction behaviour of tailings under cyclic simple shear testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 250–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N Clarke, J Hunt, A Barros, N Guerrero, L Keeney

Grade Engineering® (GE) involves a range of integrated technologies and operating protocols for improving effective feed grade through early rejection of low value material prior to costly processing activities and has the potential to transform the economics of large, low grade, mining operations. Extensive GE test work by AngloGold Ashanti (AGA) and the Cooperative Resource Centre for Optimising Resource Extraction (CRCORE) determined that the Gramalote gold deposit in Colombia is highly amenable to implementation of grade-by-size screening to upgrade the ore at a production scale. To understand the relationships between geology and the upgrade response drill core and bulk samples were analysed at the Centre for Ore Deposit and Earth Sciences (CODES) as part of a larger CRCORE project to understand geological controls on grade-by-size deportment, i.e., the tendency for specific mineral phases to preferentially fractionate during breakage into different size fractions. This work is focussed on understanding the role of mineralogy and texture in influencing rock breakage and natural fractionation at a range of scales. Detailed logging of Gramalote drill core and mineralogical analyses including hyperspectral logging, portable and bench-scale X-ray fluorescence (XRF), plus low resolution Laser Ablation of intact drill core pieces, combined with data from site (drill logs, geochemistry, petrophysics) were used to evaluate the ore and alteration mineralogy, vein paragenesis and textural variability. This provided information on gold deportment and allowed the identification of favourable host veins. Bulk sample material from different ore grade zones was also analysed. A comparison with the results of GE testing shows that positive upgrade results are produced by rocks with abundant veins, particularly those associated with potassic and/or white mica alteration. This work indicates upgrade response can be predicted from drill core using data collected by a combination of automated systems including hyperspectral data, XRF, and detailed drill core logging.

Nov 10, 2020

By L B. Zhou, S Li, B L. Wang, S B. Li, Q Wang

The rapid development in ChinaÆs metal mine resources has caused a series of mine environment problems such as serious ecological damage and environment pollution, and secondary geological disasters. The paper has reviewed ChinaÆs metal mine development, including current status and environmental situation, analysed existing problems in mine development and environmental management, and proposed corresponding countermeasures and suggestions.CITATION:Wang, B L, Li, S B, Li, S, Zhou, L B and Wang, Q, 2012. Current situations, problems, countermeasures and suggestions for ChinaÆs metal mine development, in Proceedings Life-of-Mine 2012 , pp 353-356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Higgins

Measurement while drilling (MWD) techniques can provide a useful tool to aid drill and blast engineers in open cut mining. By avoiding time consuming tasks such as scan-lines and rock sample collection for laboratory tests, MWD techniques can not only save time but also improve the reliability of the blast design by providing the drill and blast engineer with the information specially tailored for use. While most mines use a standard blast pattern and charge per blasthole, based on a single rock factor for the entire bench or blast region, information derived from the MWD parameters can improve the blast design by providing more accurate rock properties for each individual blasthole. From this, decisions can be made on the most appropriate type and amount of explosive charge to place in a per blasthole or to optimise the inter-hole timing detonation time of different decks and blastholes. Where real-time calculations are feasible, the system could extend the present blast design even be used to determine the placement of subsequent holes towards a more appropriate blasthole pattern design like asymmetrical blasting.

Jan 1, 2001

By S A. McManus

With the advances in software speed and capability, many of us now are running multiple scenarios on entire models rather than just testing small areas or a few blocks. In the authors experience both the geological and geostatistical academic theory and our rules of thumb, often prove un-useable or incorrect in the real world we work in. The only way to truly validate and tune our models is to complete the entire model and ‘see if it works’. If it lacks some property we were expecting, then we need to find out why and/or run different scenarios to see what changes. This is not always possible with tight project timelines but we find ourselves doing more and more of this sort of thing, and in so doing, understand that every deposit is different and requires its own ‘rules’ to get valid and useful results. For the purposes of this paper, this process is termed Empirical Geostatistics. Take Clayton Deutsch’s ‘all realisations all of the time’ concept a step back. Before you even think of simulating, test the alternate realisations generated by alternate parameters such as different domaining, varying search neighbourhood parameters etc.

Mar 22, 2022

By G Haywood

This paper presents the evolution of the planning, scheduling and mining practices at the Yilgarn Star underground. The paper will concentrate on the principals of æjust in timeÆ and the impact of such practices on mine planning and scheduling and subsequent development and production. The principals of æjust in timeÆ were developed to minimise the impact of creep and time dependent failure of the ground in the ore and hangingwall zones. These zones are characterised by altered schistose material with inherent weak rock strengths compounded, at depth, by the maximum principal stress of the virgin stress field approaching the UCS of the rock mass. Yilgarn Star underground has and continues to develop the æjust in timeÆ methodology to ensure the continued viability of the mine. The mine continues to use longhole open stoping mining methods to ensure high levels of productivity with minimal dilution and at an acceptable cost of production.

Jan 1, 2002

By M Andrew, H Reynolds, R Mills

As the global mining industry continues to grapple with ‘black swans’ (high consequence / low frequency events) for health, safety and environmental losses, the focus is shifting from risk assessment of these events to risk management using selected purposeful controls that reduce the risk.Fundamental to critical control management (CCM) is a soundly based rationale for selecting the right controls for each and every risk. The approach should be based on a thorough understanding of the dynamics of the event: What causes it? How frequently will it occur? How likely is the consequence to be realised? This is typically done through a bowtie and methodical numerical risk analysis. Core to this step, then, is the structure and content of the bowtie; specifically, the analytic architecture that is used to construct the bowtie. Different architectures yield different constructions, and bowties are no different.Although bowties for operational health and safety (OHS) hazards appear to have a common architecture, they are not generic. It is important to stress that they contain site specific information, are prepared by site based operational teams, and vary from site to site to reflect each site’s operational conditions. They are often a product of the knowledge and understanding of the operational teams involved, may be prone to human error, and potentially miss latent hazards that may have been embedded early in the planning, design or construction phase of a mine or facility, or within the mining equipment. Overcoming these deficiencies through constant re-evaluation of the risks, and challenging the content on the bowtie will help to minimise the chance that something will be missed.This paper will cover key themes in bowtie architecture, introduce the concept of barrier models for high consequence event (HCE) bowties and present a relevant case study to illustrate the issues that determine quality in bowtie construction and critical control (barrier) selection and management.CITATION:Mills, R, Andrew, M and Reynolds, H, 2016. Can we stop a black swan breeding? Advances in bowties and critical control management, in Proceedings International Mine Management Conference, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016