Search Documents

Attempt has been made to determine the nature of charge on activated carbon surface by studying the electro-kinetic properties of the carbon in the presence of cations, anions and aurocyanide solutions. The zeta-potential measurements were made in the presence of individual ions and also in combinations. The cations and anions chosen were those commonly associated with gold bearing ores in Kalgoorlie area. It was found that the iso-electric point of Norit Carbon was at pH 4.45; below this pH the charge was positive, while above, it was negative. In the absence of gold cyanide solutions and in the presence of individual cations the i.e.p. shifted to the alkaline range (pH 7.2-8.5) while in the presence of anions the i.e.p. was shifted to less than pH 3.5. In the presence of aurocyanide solutions, the iso-electric point was still in the acid region irrespective of whether anions or cations were present. The probable mechanism for such a behaviour has been attempted after measuring the specific conductivities of solutions before and after gold adsorption, by studies using the electron- probe-mirco-analyser, and S.E.M. on the carbon surface.

Jan 1, 1982

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

Various software packages are discussed. These are components of an Integrated Planning and Scheduling System developed by MVM with the aim of providing up-to-date information for the Whaleback operation on: 1. Mine Topography. 2. Status of equipment in the mine. 3. Material moved from and within the mine. 4. Volume and density of same. 5. Quality of same.

Jan 1, 1986

By Dennis B

The Hilton Mine, 20 km north of Mount Isa was discovered in 1947. The underground mine has been a significant producer from 1989. The long development history is the result of complex orebody geometry, difficult metallurgy, dewatering problems and competition for development funds from the then expanding Isa Mine at Mount Isa. At present it produces 1.4 million tonnes annually. Its 21 million tonnes of reserves are necessary to supplement Isa Mine production.Hilton Mine is located in the Urquhart Shale formation of the Mount Isa Group, within the Mid Proterozoic Mount Isa Inlier. The seven developed orebodies have suffered strong structural deformation. Each orebody has a unique mixture of mineralogy and texture which effects ore value and metallurgical performance. These characteristics have proven useful for correlation purposes.The faulting and folding have caused difficulties with orebody interpretation, geomechanical complexities and has influenced the choice of mining methods: Initial cut and fill and open scope designs have given way to bench mining methods in response to better understanding of the eedloav and economic constraints.

Jan 1, 1993

At the Highway gold deposit, 37 kilometres south of Charters Towers, gold mineralisation occurs in several stratiform layers and is enriched near the surface by lateritic weathering. The host rocks of the mineralisation are ferruginous and baritic, intensely sericitised, kaolinised and silicified rhyolitic tuffs and pyroclastics of the Cambrian-Ordovician Mount Windsor Volcanics. The geology of the deposit is illustrated in Figures 1 and 2.Forty-six reverse circulation percussion drill holes were completed by North-Queensland Resources N.L. for a total of 2,093 metres of drilling to further outline and test the open pit resource. The drilling indicated a resource of 171,000 tonnes averaging 4.4 grams per tonne gold and 5.0 grams per tonne silver.A shallow initial pit, approximately 30 metres deep, has been designed to mine the high grade upper portion of the western stratiform layer and part of the eastern layer. This initial pit is designed to mine 45,400 tonnes of western mineralisation at an average grade of 7.84 grams per tonne gold and 22,200 tonnes of eastern mineralisation at an average grade of 1.42 grams per tonne gold. Waste is estimated at 110,900 tonnes.

Jan 1, 1986

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

By G de Jong, W Sunyoto, M Cloos

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Ertsberg mining district is a 100 km2 area in the highlands of Papua, Indonesia. The district hosts mineralised and barren, outcropping and hidden porphyry and equigranular intrusions. There are at least six major (100+ m wide) porphyry intrusions identified from surface and underground mapping and drill cores. These are the Grasberg Igneous Complex (GIC), Karume porphyry, Lembah Tembaga porphyry, Ertsberg Stockwork Zone porphyry, Kay intrusion and the Wanagon intrusion. Recent deep drilling adjacent to the GIC identified a new hidden porphyry at depth, the Gajah Tidur (Sleeping Elephant), which extends south-west beneath the Kucing Liar skarn. Other named small porphyry dykes and plugs in the district include the West Grasberg, North Grasberg, Idenberg, South East and Zaagkam intrusions. The largest equigranular intrusion is the multiphase Ertsberg diorite.Igneous activities occurred in a relatively short span (<1 million years) from about 3.4 Ma to 2.7 Ma ago, based on U-Pb zircon dating. The various intrusions in the district related to ore mineralisation are high K and appear to have been derived from the same parental chamber, based on similar whole rock rare earth element patterns. Radiogenic Nd- and Sr-isotopic variations indicate that there were multiple recharge events into the parental chamber.The larger intrusions and all economic mineralisation occur in a 4 km wide zone that parallels the N60W-trending axis of the Yellow Valley Syncline (YVS), one of the large folds generated during collisional tectonism. Intrusion pathways at ~3 Ma were localised into dilatational areas in a late and/or post-collisional NW-trending, left-lateral strike-slip zone with Riedel shear offsets between the major fault zones. An early phase of lower K magmatism produced small intrusions in the south-west limb of the YVS.CITATION:de Jong, G, Sunyoto, W and Cloos, M, 2015. Composition, lithochemistry and radiogenic isotopes of porphyritic and equigranular intrusions in the Ertsberg mining district, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 347–356 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By King D, Dickinson S. B, Matheson R. S

Commencing in 1956, Rio TInto Australian Exploration Pty Limited in association with Electrolytic Zinc Co of Australasia, Limited, has been carrying out a mineral prospecting program in North-West Tasmania over an area of about 4000 square miles.The program has comprised extensive airborne geophysical surveys, detailed geological mapping, ground geophysical and geochemical investigations. Out of the wealth of new data, and the examination of previous records, has emerged a new structural concept of regional ore control and distribution in North-West Tasmania. This roncept stems from the discovery of an ancient 'fossil' rift valley (graben), named the Owen Rift Valley, along which are located the major mines of the area and numerous well-known prospects. The known mines and prospects from north to south include Mt Bischoff (tin); the Pinnacles (zinc, lead, ropper); the Chester (pyrites); Rosebery-Hercules (lead, zinc, ropper, silver, gold); Mt Tyndall (lead, ropper, zinc); Comstock and Tasman (copper, lead, zinc); Mt Lyell (copper, pyrites, gold); Mt Jukes and Mt Darwin (ropper). The identification of the West Coast (Owen Conglomerate) Range as a fossil rift valley is due to Or B Campana, who carried out extensive geological mapping and interpretation work, and who, with S B Dickinson, are the senior authors of this paper.S B Dickinson, who introduced B Campana to the geological problems of West Tasmania, had previously investigated the Mt Lyell and Rosebery mining fIeld, to which reference is made in this work.D King assisted in the regional mapping and in providing numerous data on the mineral distribution of the area.R S Matheson rontributed to the fmdings on ore emplacement and rontrol in the discussions held on this subject. They are accordingly included as joint authors of this paper.Credit is also due to E McCarthy, who interpreted the geophysical results, and to J H Rattigan, who compiled the preliminary geological maps from published documents and by photo-geological methods.G Hall and V H Cottle, of the Electrolytic Zinc Co in Rosebery, provided invaluable geological data and suggestions in the course of the survey, and made a constructive criticism of the manuscript of this work. The airborne geophysical survey carried out by the Adastra-Hunting Geophysics Ltd company, furnished useful data which substantiated many of the fIndings on the stratigraphic and structural relationship. The Mines Department of Tasmania and S W Carey, Professor of Geology at the University of Tasmania, were instrumental in initiating the regional survey and provided the published and unpublished geological literature on the area.The authors also wish to acknowledge the invaluable assistance received from the Mt Lyell Mining and Railway Co in Queenstown, which made available the more recent geological and mining documents rompiled by M L Wade and M Solomon.

Jan 1, 1994

By Martin C. H, Met B

INDEX OF CONTENTS:1. Introduction, Explanatory; and Reasons for Coal Cleaning.2. Principles on which Coal Cleaning is based.3. Location of Broken Hill Proprietary Co. Ltd. Plant.4. Description of Processes Selected Barvoys Bath Process; Barvoys Medium Preparation and Treatment; Static Dry Cleaning Plant.5. Detailed Description of Plant.6. Typical Results of Cleaning Operations.INTRODUCTION, EXPLANATORY, AND REASONS FOR COALCLEANING:The Institute proceedings have not previously published any matter on coal cleaning and the reasons thereof; in consequence it has been deemed advisable to allot a part of this paper to explanatory matter, prior to entering into a detailed explanation and description of the Newcastle plant.At the outset it would be as well to consider briefly the kinds of materials from which coal has originated. All coals represent some stage in the decomposition and transformation of vegetable matter laid down in prehistoric times, the vegetable matter undergoing numerous geological changes, such as submergence, overlaying by sediment, with subsequent pressure and re-elevation; these processes may...

Jan 1, 1946

The Cadjebut Mine is located 80 km southeast of Fitzroy Crossing. Cadjebut is owned 58 per cent by BHP Minerals and 42 per cent by Billiton Australia. Cadjebut is a 'Mississippi Valley Type' (MVT) deposit. Minerals present are sphalerite, galena and marcasite in a sedimentary host of dolomite and siltstone. The ore contains few deleterious impurities and no silver. The mill was commissioned in the first half of 1988 at a rate of 320 000 tonnes per annum. An expansion in the latter half of 1989 has since increased production to 550 000 tonnes per annum. The initial geological resource at the commencement of mining was 3.8 million tonnes at 13.5 per cent Zn and 4.4 per cent Pb. There is sufficient ore left to sustain operations to 1995 at a grade of 11.2 per cent Zn and 3.9 per cent Pb. The ore from underground is stockpiled on the surface via a drift conveyor and from the stockpile is fed into a grinding circuit consisting of a SAG and ball mill. Cyclone overflow at a Pgp of 90 pm gravitates to the flotation circuit. Lead and zinc are sequentially floated to produce an 80 per cent Pb grade at 90 per cent recovery and a 61 - 62 per cent Zn grade at 96 per cent recovery. The concentrates are thickened and filtered before being trucked to the port of Wyndham 600 km away. From Wyndham the concentrates are shipped to smelters in Asia, Europe and Australia.

Jan 1, 1992

By Paine GG

The Kidston Gold Mine commenced mining in 1984 and current annual production is 12 million tonnes, increasing in 1990 to 18 million tonnes. Mill throughout per year is 4 million tonnes with the balance of material being waste. The operation is a conventional hard rock open pit truck and shovel operation mining 12 metre benches. Buffer blasting is utilized to minimize post blast movement of the broken rock to maintain grade control.

Jan 1, 1988

The Manto Verde copper mine (Atacama Region, Chile) is due to go into production in 1996. It will produce 40 000 tonne/year of copper cathode by heap leaching/SX-EW. Mineralogical studies were undertaken in conjunction with the metallurgical testwork program to characterise the ore and its response to leaching by dilute sulphuric acid. The leachable copper mineralogy is dominated by the oxide copper minerals: brochantite and malachite with minor chrysocolla and atacamite. The gangue minerals include abundant orthoclase, specularite, quartz and chlorite with minor muscovite and trace smectite clay, calcite and limonite. The study showed that complete or partial decomposition of calcite, chlorite, smectite and wad consumed acid and generated solution impurities (Ca2+, Fe2+, Mg2+, A13+, K+, Si4+ and Mn4+2+ ). Although these were manageable at Manto Verde, their uncontrolled build-up could have affected the operation in several ways: the degradation of heap penneability and fonnation of crud in the SX plant from the precipitation of gypsum, goethite, colloidal silica and jarosite; and the entrainment of contaminated pregnant leach solution in the SX organic resulting in the transfer of impurities to the electrolyte and subsequent effects on cathode quality and electrowinning efficiency. In conclusion, process mineralogy played an important role in understanding and managing potential mineral-related problems in the heap leaching and SX-EW recovery of Manto Verde ore.

Jan 1, 1994

By J Kovacs

Underground development drill and blast practices have generally remained unchanged for decades. Historically, development optimisation has focused mainly on the application of perimeter control products in order to reduce overbreak, and efficiencies in development cycle times to increase advance rates. In today’s environment of ever increasing operating costs and lower ore grades, it has become even more critical to focus on the optimisation of drill and blast in development mining. It is a crucial component in ensuring mining schedules are maintained, but more importantly achieving the objective of getting to the orebody in the shortest possible time.This paper will focus on the development optimisation process used in a trial at Xstrata’s George Fisher Mine in North Queensland. Not only did the trial include the typical optimisation areas of charge loading practices, perimeter control methods, drill design standardisation and quality control processes, it also investigated the significance of delay accuracy with regards to perimeter control and drill design optimisation.One of the key measures of the trial was a comparative analysis between baseline development and development with the staged introduction of optimisation elements using 3D photogrammetry as a validation tool. A detailed cost analysis between the various stages was also a key measurable of the trial.The results of the work undertaken at George Fisher have shown that the accuracy of electronic detonators can produce significant benefits in development blasting. When combined with standard optimisation philosophies a substantial reduction in overbreak, ground support requirements and development cycle times can be achieved, whilst still being able to reduce the overall development operating costs.CITATION:Kovacs, J, 2014. Mine development optimisation – an evolutionary process, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Wightman D, Hoyle M. W H, Peters W. S

The Radio Hill nickel-copper deposit is located 30 km south of Karratha. It is a new discovery in an area where similar mineralization had been previously discovered at Mt. Scholl and Ruth Well. Radio Hill is the first massive Ni-Cu sulphide deposit of economic significance to have been located in the Western Pilbara.Preliminary studies indicate that the sulphide mineralization occurs within gabbros, pyroxenites and peridotites of a basic igneous cumulate layered sequence. Primary sulphides have been subsequently remobilized and concentrated as stringer and massive mineralization. This is tentatively attributed to the intrusion of a further gabbroic body.The deposit appears to be of the gabbroic association type with a Ni:Cu ratio varying from 1:4 in the outer parts of the mineralized envelope to 1:0.9 towards the central zones. In drill core observations, chalcopyrite surrounding pyrrhotite was noted in many instances. Drilling has so far delineated a body developed over a strike length of 600 m and a horizontal width of up to 25 m. The mineralization plunges 20° to the southwest with a southerly dip varying from 75° in the west to about 20° - 30° in the east.The deposit is a leaf-shaped ore zone, plunging southwest from a vertical depth of 17 m in the north to 300 m in the south. The massive sulphides occur as lensoid masses within this zone. A geological resource of up to 2.5 million tonnes at 1.5 per cent Ni and l.4 per cent Cu is indicated.The predominant sulphides are pyrrhotite, chalcopyrite and pentlandite, with significant cobalt, platinum group metals and gold. Tellurides of Pd, Bi and Pb were detected by scanning electron microprobe within the pyrrhotite and other trace metals include Zn and native tin. Massive magnetite is sometimes associated with the massive pyrrhotite intersections.A test on one composite massive sulphide sample showed that pyrrhotite is present mainly as the non-magnetic hexagonal variety and only 10 per cent is present as magnetic monoclinic pyrrhotite.The deposit has no surface expression and its identification was based mainly Oil drilling targets generated by geophysical methods. No secondary minerals have been observed in association with the primary sulphides, even though the deposit is only 17 m below surface in the northern part.

Jan 1, 1987

The brown coal resources of the Latrobe Valley, which include over thirty thousand million tons of coal suitable for open cutting, provide the main source of fuel for the power generation for the State of Victoria. They also provide the basis for the development of a supply of cheap hard fuel for industrial and domestic use, and for the development of the Lurgi process for manufacture of town gas for most of the State. The production of hard char for metallurgical processes and liquid hydro carbons will each, no doubt, play its part in the industrial growth that will be based on these resources.The State Electricity Commission of Victoria, which has been allocated the task of developing these deposits since the early 1920's, is faced with problems of economic selection of deposits for development, and excavation and transport of huge tonnages of coal and overburden-in this year, 19'59, about 12,000',000 tons of brown coal will be won, and over 7,000,000' cu. yd. of overburden will be removed in the four open cuts operated by the Commission; by 1967, eight years from now, the demand will have doubled.This paper deals with the nature and importance of various factors effecting the planning of the development of these resources. It is in essence an introduction to the papers by C. S. Gloe, H. C. G. Rodgers and J. M. Alexander, also being -presented at the Institute conference in Victoria in August, 1959.INTRODUCTIONIt is the intention in this paper to define the factors that come under consideration in the planning and development of the brown coal fields in the Latrobe Valley, whose exploitation by the State Electricity Commission of Victoria was initiated almost 40 years ago. It is proposed to enumerate, and in sorile cases evaluate, the physical and economic criteria that play their part in determining planning for the future.

Jan 1, 1960

By Hebblewhite B, Humphreys D

An experimental mining project has been carried out in the Collie Basin to demonstrate the safe operation of total extraction mining techniques in the underground mines of the basin. To achieve this, it was necessary to design and install a means of controlling or removing groundwater so that goafing of the overlying strata could be safely achieved as part of the mining operation. The site chosen for the experiment was a triangular panel adjacent to Western No 6 (WD6) underground mine, which includes the 3 to 4 m thick Wyvern Seam beneath 130 to 180 m of overburden. The test area abuts a major fault on the downdip side. The overburden and underburden sequences include several horizons of permeable sandstones which form major aquifers. Water problems have long been recognized in all underground mines in the Collie Basin, and have previously prevented the successful application of total extraction mining. Following extensive hydrological investigations, dewatering and depressurization systems were designed to dewater the immediate roof aquifers and to depressurize aquifers higher in the sequence and in the floor. This would enable stable roof conditions to develop and controlled goafing to be achieved. The roof dewatering/depressurization procedure involved a combination of in-mine vertical roof drainage holes and conventional dewatering bores constructed from the ground surface above the mining trial area. The dewatering system was installed and operated for 29 months before the commencement of mining. Mining was eventually successfully completed in two trial panels using a retreat Wongawilli extraction system using bridge conveyors and continuous miners. Water inflow into the mine workings was channelled to a constructed sump area at the lowermost corner of the panel and pumped to the surface via vertical sump bores. The dewatering and depressurization measures adopted were successful in permitting the first controlled and systematic total extraction recovery of coal from the Collie Basin. This trial mining exercise demonstrated the potential for increasing substantially the recovery of coal from the Collie Basin, where previously recovery rates of around 30 percent from underground mining were commonplace, using only bord and pillar methods.

Jan 1, 1988

A failure of the Pit IA highwall in July 1989 led Newcrest Mining Ltd's Telfer Gold Mine to commence underground operations approximately 12 months ahead of schedule. The failure presented four major challenges to management: 1. how to maximise the recovery of the Middle Vale Reef (MVR) in the open pit: 2. how to minimise the risk to personnel involved in the extraction of the remaining open pit ore; 3. how to avoid disruption to ore supply: and 4. how to maintain a permanent and safe means of accessing the underground operations from the base of the pit. The risks associated with meeting these challenges were minimised through the installation of a complex network of real time slope monitoring equipment. These monitors were connected to an alarm system which was combined with detailed operational procedures to be carried out in the event of a highwall alarm being triggered. The accuracy with which the risk of failure has been managed was demonstrated recently when the onset of a second failure was initially identified some 13 months prior to its ultimate collapse in October 1992. The location, timing and size of the failure was able to be predicted allowing appropriate precautionary measures to be taken to ensure safety of access to the underground portal and pumping equipment in the base of the pit. This paper reviews the sequence of events leading to both the July 1989 and October 1992 failures of the Pit 1A highwall and the monitoring equipment and procedures used to identify, quantify and manage the risk to personnel operating in the base of the pit.

Jan 1, 1994

Answers to the questions "which rocks contain diamonds?" and "which indicator minerals should diamond explorers look for?" are no longer so easily obtained, now that diamonds are known to occur in lamproites and various types of lamprophyres, as well as their traditional source of kimberlites. One way of isolating those factors (host-rock"geochemistry, geographical or tectonic location, xenolith minerals, etc.) which are most critical in determining the diamond potential of a given pipe, is a detailed and critical re-examination of the huge volumes of accumulated data on kimberlites, lamproites and related rocks. A large analytical database to this end has been set up on an Apple Macintosh II microcomputer using the quasi-relational database management system 4th Dimension. Currently, it contains data for up to 90 major and trace elements, isotopic ratios and contained mineral compositions for some 4,000 rock specimens from all over the world. Many experiences in setting up this database are probably relevant to other geologists setting up their own systems: they include determining the relationships between data items; the advantages of codes over free text in representing categorical variables such as rock types; the need for rigorous error trapping and data validation; and the problem of missing data values and ambiguities thereof. The working system is now being used in a rigorous statistical assessment of the criteria which distinguish diamondiferous from non-diamondiferous rocks.

Jan 1, 1989

By Tien J. C

Many factors (type of coal mined, water pump pressure, wetting agent concentration, etc) will affect the performance of a dust suppression system using a water spray in an underground coal mine. While a two-level factorial method is useful in

Jan 1, 1994