Search Documents

By H. C. Lukens, E. V. Potter

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By G. W. Hodges

The Basic Oxygen Process shop at Gary Works is a three vessel shop tapping 220 ton heats. The larger portion of the heats are teemed into ingot molds with the remaining heats being continuously cast in a single strand continuous slab caster. Ingot production includes a wide range of carbon, alloy, and high-strength steels in many ingot sizes for bar, structural, plate and sheet and tin products. Individual ingot weights vary with the number of ingots per heat ranging from a high of 48 to a low of five. Caster production is primarily Riband, a proprietary low carbon grade for sheet and tin applications developed by United States Steel for continuous casting; some Riband steel is vacuum degassed prior to casting. Maintaining a satisfactory level of ladle performance on both ingot and caster heats with a high production rate and widely varied product mix is a demanding and exacting job requiring the best of equipment, materials, and, most importantly, personnel. The improving trend in ladle performance in the No. 1 BOP shop at Gary is due to a combination of factors, which will be described in the following presentation.

Jan 1, 1972

By E. E. Schumacher, G. S. Phipps, H. M. Bouton

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By H. M. Bouton, G. S. Phipps, E. E. Schumacher

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

INTRODUCTION TO MINERAL INVENTORY The first explanations to be made must answer the questions: What is a mineral inventory, and how is a mineral inventory different from an ore reserve? The term mineral inventory is a relatively new designation-born of the computer age and grown to common usage with the development of computer techniques for extending drill-hole sample values to regularly gridded data blocks representing in situ mineral values. The term has been generally accepted by geologists and engineers because it has a precise meaning which avoids many of the ambiguities of ore reserve. A mineral inventory is an estimated inventory of mineral in place and is usually achieved by dividing the deposit into regularly spaced gridded blocks to which are assigned estimated values using various extension techniques. A mineral inventory makes no presumptions about the mineability of the blocks or their cutoff grade. Such parameters are implied with the use of the term ore reserve. Ore has a specific definition (see Chapter 1) and ore reserve must reflect that definition and thus has economic and mining constraints. An ore reserve will be different under different economic and mining conditions and is subject to reclassification by many factors. The term mineral inventory avoids all such ambiguities. A mineral inventory estimate may be good or poor according to how much is known about the deposit, how extensively it has been sampled, and what techniques have been employed to assign estimated grade to the blocks. Such an inventory, however, does not change with time, economic conditions, or mining technology, but only with new and better data and methods. Thus, the mineral inventory is an excellent designation for describing mineral value distribution within a deposit's geological setting. The techniques for assigning values and tonnage to mineral blocks or panels are the subjects of this chapter. Whether a summation of the blocks be called a mineral inventory or mineral reserve is not important. Many conventional methods for computing reserves of minerals refer to the methods in terms of ore reserve calculations. OBJECTIVES OF MINERAL INVENTORY OR RESERVES Mineral inventories are computed for the purpose of determining the quantity, the quality or value, and the spatial distribution of potentially economic minerals within the earth. Such computations are made at all stages in the life of a mineral extraction process, from the early exploration phase to the final year in the life of a mine. To quote Popoff (1966, p. 2), "They are the most responsible and irreplaceable tasks in the valuation of a mineral deposit. Efficiency in extraction and productiveness is impossible without accurate reserve computations." The accuracy of estimate required for each of the three parameters of quantity, value, and location is dependent upon the objective for which the reserve estimate is being made. Again quoting Popoff (1966, p. 2): Reserves are computed to determine the extent of exploration and development; distribution of values; annual output; probable and possible productive life of the mine; method of extraction and plan design; improvements in extraction, treatment, and processing; and requirements for capital, equipment, labor, power, and materials. Such computations are used to assist development

Jan 1, 1980

By Henry S. Poole

This field is geologically of much interest. It is small, hut with some seams of unusual thickness, the main one being as much as thirty-eight feet thick. The quality of the seams, as also of the associated beds of shale and sandstone, in several instances changes to a remarkable degree within short, distances. The strata dip at inclinations that carry the coal to depths of 3000 feet or more; heavy faults cut up the district, and the New Glasgow conglomerate, of disputed age, separates it from the Upper Carboniferous measures, in which no seams of workable thickness are known. This coal-field offers to the geologist much ground for study and peculation. The commercial value of the field is affected by its restricted area, the varied quality of its coal, and its advantageous position in the mainland, with railway connection and home markets, offset by the physical difficulties which make the cost of production high. It has been so long a habit with us to speak of our resources of coal as boundless, that any adverse comments, or insinuations that avoidable loss in working is a national loss, hare hitherto fallen on idle ears. While it is not my purpose to underrate the riches we do possess, yet I deem that no good end is served by echoing exaggerated estimates which encourage a national indifference to wasteful

Jan 1, 1886

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By F. W. Sperr

The byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.).............................. 69 per cent. of coal Domestic coke (1/2 to 3/4 in.)................................ 2 per cent. of coal Breeze (under 1/2 in.)...................................... 4 per cent. of coal Surplus gas, cubic feet per net ton........................... 6600 Gas for heating ovens, cubic feet per net tor i................. 4400 Tar, gallons per net ton.................................... 9 Ammonium sulfate, pounds per net ton....................... 25 Benzols, gallolls per net ton................................. 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke," ('beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writeri stated that in brass-foundry practice, Connellsville coke is considered rnuch superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in making general statements like these. The percentage of sulfur in coke depends largely on that in the original coal, and byproduct coke from a

Jan 1, 1921

By N. P. Peterson

THE Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyrite and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyrite zone being the protore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment.

Jan 1, 1947

By M. K. Barnett

[ ] ENGINEERING research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency-i.e., the attainment of the maximum amount of reliable, useful information relating to the influence of the factors on the property of the product or characteristic of the process, for the least expense-is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modem methods for the analysis and evaluation of experimental data. The present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1947

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By E. A. Gulbransen, J. W. Hickman

Recent work by the authors1 on the oxide films formed on alloys of titanium and zirconium with nickel and copper indicated that an investigation of the oxides which form on alloys of copper and nickel might permit the relative rates of formation and diffusion of the ions of these metals to be determined. This binary system is of further interest since the alloys which form are of the solid solution type over the entire range. In addition nickel is much more oxidation resistant than copper. A comparison of the free energies of formation of the simple oxides which may occur on these alloys indicates that nickel oxide should be observed over the entire time and temperature ranges of oxidation for all alloy compositions~i In order for nickel oxide to predominate on the surface, it is necessary that nickel ions form and diffuse to the surface. Two factors which may influence the formation of nickel oxide may be the ionic sizes, where cu+ is o.,,6-,4 and ~i++ is o.,oh;, and the charges on the ions. On the basis of size, Ni++ should diffuse more readily than Cu+ while on the basis of charge, Cu+ should form more readily than Ni++. According to Uhlig2 passivity to corrosion in an alloy appears at a critical composition which for copper-nickel alloys is related to the tendency of the d band of electronic energy states to fill with elec-trans. This in in the copper- nickel alloys corresponds to 40 at. pct nickel at which composition Uhlig2 (quoting La Que's data) states that the alloy system becomes passive. Magnetic and specific heat data indicate that the d band of copper-nickel alloys is flied at 60 at. Pet Or or 4O at. pct nickel. Matt and Jones3 have shown that if, on alloying nickel with copper, one considers a copper atom to be identical with a nickel atom except for an extra electron (nickel has the configuration: 3ds 4s2 and copper: 3 dl0 4s) then at 60 at. pct copper or 40 at. pct nickel enough electrons are contributed by copper to fill the d band of the alloy. At this composition the magnetic susceptibility approximates zero according to Grew.4 Although the electron diffraction data will not determine the rates of the several reactions which may occur during oxidation, yet a determination of the structures of the surface oxides may yield information concerning the relationships, if any, which may exist between the oxide structures which form and that composition where the magnetic susceptibility approximates zero. It is quite possible, of course, that the mechanisms of the oxidation and corrosion reactions may be so widely different that no correlations between them may be possible. Survey OF Literature The metals, copper and nickel, which are face-centered cubic, form solid solution alloys which are face-centered cubic with no superstructure for all compositions. Three oxides of nickel have been investigated structurally by X ray diffraction. Of

Jan 1, 1949

SEC 1 The membership of the Institute shall comprise seven classes, namely 1 Members, 2 Honorary Members, 3 Senior Members, 4 Associates, 5 Junior Members, 6 Rocky Mountain Members, 7 Junior Foreign Affiliates All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote SEC 2 Members A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields This shall not apply to Rocky Mountain Members SEC 3 Honorary Members Each candidate for Honorary Membership must be recommended by the Committee on Honorary Memberships and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present, provided, however, that the number of Honorary Members shall at no time exceed twenty Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong SEC 4 Senior Members The Directors may, at the special request of any Member or Associate who has reached the age of seventy years and who has paid

Jan 1, 1952

By James Munroe

APPALLING as has been the loss of life in the last 51 months, there is one slight compensation : no longer will there be in the world a cripple, in the old meaning of the term. Men handicapped by wounds or disease, there will be, unfortunately, and in numbers beyond what the world has known since the wars of Napoleon; but neither they nor the industries from which they were called off to war will be "crippled" in the sense in which both would have been had mankind not learned the lesson of conservation and come to understand that the most important field for such conservation is not in the forests and' the mines but among men and women. From the beginning of the Great War, France, Great Britain, Belgium, and most of the other Allies have studied the problem of restoring the soldiers and sailors injured through war to physical and economic efficiency; and from their experiences, especially from that of Canada, the United States has learned much. Consequently, our task of preparing for the return of our disabled men has been easier and, in some ways, more comprehensive than theirs. Complex as are the details of the machinery which the United States has set in motion to take care of the men injured by wounds or disease, the plan itself is simple. Taught by European experience, the Surgeon-General of the Army and the Bureau of Medicine and Surgery of the Navy have provided, on both sides of the Atlantic, every known surgical and medical facility for restoring the injured or diseased man to a physical condition as nearly normal as possible. While in the hospital in France or England, on the transport coming to America, and in the hospital here, the disabled man is incited in every way to believe in his future efficiency, to want to be a normal worker, to desire to retake his place in that society of workers from which he went, temporarily, to do the greater work of preserving civilization. Furthermore, since purposeful occupation is now regarded as an essential form of, treatment with most men in the hospital, especially in the convalescing stage, many of these men will have been actually started on the road to earning before they are discharged from the army surgeon's care.

Jan 1, 1919

By Jeffrey N. Schuyler

In order to implement the most efficient and cost-effective hydraulic fracturing stimulation treatment within a particular region, a thorough understanding of the in-situ stress state and rock properties is paramount (Smith et al., 1978; Warpinski et al., 1982). Several studies conducted in order to "characterize" formations have provided invaluable insight into the relationship between lithologic properties, depth, in-situ stress magnitude and hydraulic fracture orientation. These studies have substantiated that at shallow depths, rock properties such as tensile strength and permeability can exert a substantial influence on the geometry of an induced hydraulic fracture. In turn, these "directional properties" can be related to existing geologic conditions during the time of deposition or major diagenetic alteration of the rock body. As the depth of the "payzone" increases, the role of the in-situ stresses and therefore the prevailing tectonic conditions becomes the dominant factor in determining fracture geometry. However, reservoir properties cannot be ignored. The porosity, permeability, pervasive fabric element and directional elastic properties can have a significant influence on the success of those tests conducted to measure the in-situ stresses either directly or through secondary observations... for instance, pore-pressure effects on measurements of in-situ stress. The purpose of this paper is to provide, through the use of appropriate field and laboratory examples, a more thorough understanding of in-situ stresses, rock properties and their integrated effect on hydraulic fracture properties. In addition to highlighting and expanding the wide body of existing literature, the case studies cited are designed to encourage mutual transfer of technology from petroleum-related, rock-mechanics efforts to other disciplines.

Jan 1, 1984

By C. H. Li, J. Washburn, E. R. Parker

Yield stress in single crystals of zinc was shown to be dependent on prior annealing temperature and rate of cooling after annealing. Rate of strain hardening beyond the yield was not sensitive to annealing procedure. A tentative mechanism for the effect was discussed. COMPARATIVE mechanical tests of metal single crystals generally show a large scatter of results. Many factors may contribute to this variation. The present investigation was undertaken to evaluate the influence of two factors not ordinarily considered of major importance—annealing temperature and cooling rate after annealing. Since plastic properties of crystals are thought to depend on the presence of lattice imperfections, it follows that a variation in properties should result from differences in the distribution and density of these imperfections. Furthermore, in the light of current theories of interaction between edge dislocations and lattice vacancies,' it seems possible that annealing temperature and subsequent rate of cooling might play a part in this distribution. Analysis of the effect of these variables on plastic properties may lead to a better understanding of the annealed state. Single crystals of zinc which have been strained in simple shear undergo complete recovery of mechanical properties upon subsequent annealing. This behavior is useful because a single specimen can be used repeatedly, thus eliminating the uncontrollable variables introduced by the use of many crystals. The test section of the crystals used for these experiments was a cylinder 1/8 in. thick with a cross-sectional area of about 1/3 sq in. The specimens were acid-machined from spherical single crystals 1 in. in diameter in such a way that the slip plane (0001) was at right angles to the axis of the cylinder. In testing, a shear stress was applied along one of the slip directions, [2110] in the (0001) plane.' All crystals, unless otherwise noted, were grown in a helium atmosphere from molten 99.99 pct pure Horse Head Special Zinc. Fig. 1 is a family of curves obtained from one crystal. Each curve was obtained by deforming the crystal to 10 pct strain at a rate of 3 pct per min, following an anneal of 1 hr at 260°C. The strain direction was reversed every other time so that no progressive change in shape of the specimen took place during the series of tests. Since the stress-strain curve was reproducible within a fairly narrow range under the same conditions of annealing, it was then possible to determine the effect of changes in annealing conditions. A crystal was tested repeatedly as previously described but the annealing temperature and rate of cooling preceding each test were varied (Fig. 2). Two cooling rates were used, approximately 30°C per min and 3°C per min. Annealing was conducted at three temperatures, 200°, 300°, and 400°C. For a given annealing time and rate of cooling the room temperature flow stress was higher the higher the annealing temperature. The increase in flow stress was small as the annealing temperature was increased from 200° to 300°C but rose rapidly when the annealing temperature was raised from 300" to 400°C. Faster cooling from the high temperature produced an even greater strengthening of the crystal. The curves were obtained in the order indicated by the numbers. The stress level associated with a certain annealing treatment was, within the limits of scatter, always the same regardless of the

Jan 1, 1954

By H. l. Burghoff

THE presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Egleston1 reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the. mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn).

Jan 1, 1937

By M. E. Wadsworth, A. E. Lewis, R. L. Braun

Experimental results obtained in laboratory leaching studies of primary copper sulfide ore in sulfuric acid systems pressurized with oxygen are interpreted by a computerized geometric model involving the movement of a reaction zone through the ore fragments. Physical properties of the ore, including size, shape, and mineral content, are considered. The leaching mechanism involves mixed kinetics and includes a surface reaction within a moving reaction zone plus pore diffusion of dissolved oxygen through the reacted portion of the ore fragment to the reaction zone. The results are applicable to conditions that would exist in nuclear solution mining or similar processes in which the ore is converted into rubble and then inundated by a leach solution adequately supplied with oxidants. Experimental results at 90°C are correlated with the model, which includes temperature-dependent parameters.

Jan 1, 1974