Search Documents

By R. C. Hassinger, D. V. von Rosenberg

Transverse dispersion has received considerably less treatment in the literature than has longitudinal dispersion. Different methods for determining transverse dispersion coefficients have been used in different investigations, and the results obtained have not been consistent enough to permit accurate generalizations as to the effect of various physical parameters on the magnitude of these coefficients. A numerical solution to the differential equation describing transverse dispersion in the absence of longitudinal dispersion was obtained to enable one to calculate the dispersion coefficient from experimental results. The more general dispersion equation including longitudinal dispersion also was solved numerically to give quantitative limits of a dimensionless group within which the assumption of negligible longitudinal dispersion is justified. Possible experimental procedures were examined, and one utilizing a cylindrical packed column was chosen for the determination of transverse dispersion coefficients. Values of these coefficients were determined for a system of two miscible organic fluids of equal density and viscosity, for two sizes of packing material over a wide range of flow rates in the laminar regime. The dispersion coefficient was found to decrease, for a constant value of the product of packing size and interstitial velocity, as the size of the packing material particles increased. INTRODUCTION Longitudinal dispersion has received extensive treatment in the literature, and consequently is better understood than its orthogonal counterpart, transverse dispersion. Many mathematical models of dispersion processes assume that transverse dispersion is rapid enough to damp out any radial** concentration gradients and therefore may be neglected. Laboratory and production results, however, indicate that this is a poor assumption.l,2 Various experimental procedures for determining transverse dispersion coefficients have been used in previous investigations, but the results have generally been expressed by similar correlations. The transverse dispersion coefficients obtained, however, have often varied considerably for given values of the correlation parameters. We feel that further experimental determinations of transverse dispersion coefficients will help alleviate some of the inconsistencies in these empirical correlations. One assumption implicit in all previous investigations is that of negligible longitudinal dispersion in the experimental system. An attempt to justify this assumption often is made using intuitive reasoning, but it is apparent that this reasoning must break down as the condition of zero flow rate is approached. A mathematical examination of the equations describing the system yields physical limits outside of which the assumption of negligible longitudinal dispersion is invalid. BACKGROUND In a porous medium, the "effective molecular diffusivity" De is less than the molecular diffusivity D measured in the absence of a porous medium, due to the tortuous path which a diffusing molecule must travel. Various authors3-5 have reported values of the ratio De/D in the range of 0.6 to 0.7. When there is fluid flow within the porous medium, mass transfer occurs by convective dispersion as well as by molecular diffusion. These are separate phenomena and can be treated as such on a microscopic scale. However, the mathematical complexity is such that only extremely simple geometries could be considered, and the results hardly would be applicable to the complex geometries existent in actual porous media. A more

Jan 1, 1969

By George Breyer

DURING the past 25 years the steelmaker has experienced some difficulty in producing steel to meet the standards established by the metallurgist. In contrast to the past, when a chemical specification of broad limits was the only requirement, he now has to employ such tests as microscopic, macroscopic, tensile, impact, Magnaflux and even X-ray and supersonic. The development of these tests has more than set the pace for a manufacturing process of which the exactness still hinges to an important degree on the ability of the furnace operator. In our efforts to produce steel, and especially alloy steel, to meet the exactness of modern engineering specification, many factors must be taken into account. It is not sufficient to make a good heat of steel in the furnace and then be satisfied that the job is done, since there are many pitfalls between the furnace and the finished product. The literature abounds with information on melting practices, deoxidation methods and slag control, but the lack of positive information about what happens when the steel is teemed into molds is quite evident. Such questions as what is the proper mold size, shape and thickness; which is the best mold coating; what is the best rate of pour for any given steel, and what is the effect of cooling rates on quality, are still answered by opinions. It is acknowledged that a poor heat of steel cannot be improved in the pouring pit. On the other hand, a good heat can be ruined by improper handling after it leaves the furnace.

Jan 1, 1947

By Paul A. Bailly

Around 4500 B.C., the Pharaoh of Egypt ordered a military campaign to the Sinai Peninsula and the shores of the Red Sea, to search for copper deposits which Egypt needed for jewelry, vases and weapons.5 To my knowledge, this is the first recorded expedition aimed at the discovery of minerals. The diligent Egyptian soldier-prospectors made discoveries through visual detection and manual effort, the approach which has given us the bulk of our mines to date. In the Rio Tinto District of Spain where Roman miners followed the Phoenician traders, we find the first evidence of discovery of hidden ore bodies in the absence of mineralized outcrops. This is how Joralemon 13 describes these Roman discoveries to the southwest of the Rio Tinto hills, under the flat plain of Seville:

Jan 6, 1979

By W. G. Matteson

The Oklahoma legislature recently passed a bill providing for "the creation of an oil and gas department under the jurisdiction of the Corporation Commission, authorizing the Corporation Commission to appoint a chief oil and gas conservation agent, and conferring exclusive jurisdiction on the Corporation Commission in reference to the conservation of oil and gas, and the inspection of gasoline and oil, the product of crude petroleum, and repealing all acts or parts of acts in conflict therewith and declaring an emergency." Some of the functions of the new bureau include the receiving and filing of all well logs, and the direction and supervision of plugging all abandoned oil and gas wells, under rules prescribed by the Corporation Commission. The two leading petroleum-producing States of the country, Oklahoma and California, have now established oil and gas bureaus with a staff of inspectors to see that the important rules relating to the conservation of oil and gas are thoroughly enforced. The economic significance and the value of well logs in the conservation work has been recognized, and the necessary legal action taken to insure and procure them. William B. Heroy, of the Government Land Classification Board, in a personal communication to the writer, says that the drilling of wells is also regulated by public authority in the Roswell artesian basin in southeastern New Mexico, where a permit must be obtained for the drilling of any well and a certified log of the well recorded with a county official. The method is said to give fairly satisfactory results. In a recent article1 a National instead of a State Bureau was suggested for collecting and filing well logs. In discussing the paper, L. L. Hutchison characterized such a plan as impractical because the average driller or contractor will often juggle or guess at the log and will not keep the record sufficiently close or accurate, making it necessary to maintain a special man at each well for the sole purpose of obtaining

Jan 1, 1918

By R. B. Sosman

INTRODUCTION IT is well known that ferric. oxide, Fe.-,03, is paramagnetic, while magnetite, Fe304, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe-03 and Fe304 have been almost completely lacking. Fe203 and Fe304 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe203 toward Fe304, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe304, but it has not yet been possible to establish the existence-of such a break experimentally. The occurrence of solid solution ill this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe203 to Fe304. The oxygen-pressure curves at 1,100° and 1,200° are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe203 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is im-possible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe304 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great hulk of natural oxides of iron lie fairly near either Fe203 Or Fe304 in composition. The reason will be

Jan 6, 1917

By Robert B. Sosman

The chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily I I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting On a paper that I had recently published27 On "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of of Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. Scope of the Lecture During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyro-metric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the united States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the ((temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that " temperature of the furnace " is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1949

By Robert B. Sosman

The chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily I I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting On a paper that I had recently published27 On "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of of Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. Scope of the Lecture During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyro-metric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the united States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the ((temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that " temperature of the furnace " is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1949

By Keith Leonard Sutherland, Ian William Wark

Mercaptobenzthiazole and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium rnercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group —SH or —5Na. The general method of investigation has been based on contact tests. Two temperatures, 10" and 35" C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Ian William Wark, Keith Leonard Sutherland

Mercaptobenzthiazole and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium rnercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group —SH or —5Na. The general method of investigation has been based on contact tests. Two temperatures, 10" and 35" C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,' accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952

By David P. Shoemaker, Clara B. Shoemaker

It has been shown for an important class of complex transition intermetallic compounds (a, P, R, 6, and p phases) characterized by "normal" coordination [CN12 (icosahedral), CN14, CN15, CN16/ that interatomic distances nay be calculated to a good approximation as the sum of characteristic atomic radii. Two radii, one for major ligands and one for minor ligmds, are specified for each atom, except in the case of CN12 where only a miaaor-ligand radius is specified. The same appears to be true of transition-metal phases of simpler struc-ture: Laves phases (CN12, CN16), and p-tungsten phases (CN12, CN14). In the case of known examples of the more complex phases, a simple rule is given which specifies these radii. However, only a fraction of the known examples of the simpler phases obey this rule closely. To include the latter phases the rule may be modified by considering the radii as linear functions of the weighted average of the Pauling CN12 radii of the two kinds of atonzs, with the radii weighted according to the over-all chemical composition of the alloy. With very few exceptions interatomic distances for both tlze complex and the simpler transition phases can b$ predicted with this modified rule to within 0.06A. ManY intermetallic compounds are known of composition A,By, in which A is a transition element to the left of the manganese column in the periodic table and B is a transition element in or to the right of it. Frequently the coordination numbers (CN) found in these compounds are CN12 (icosahedral), CN14, CN15, and CN16 (called "normal" coordinations by Frank and Kasperl). Well-known examples are the cubic and hexagonal Laves phases which have CN12 and CN16, and the 0-tungsten (CrsO) phases which have CN12 and CN14. In the more complicated (often ternary) phases, such as the a phase,2 the Beck phases p3 and R~, the 6 phase,5 and the p p atoms occur with CN12, CN14, CN15, and (except for a) CN16; in many cases several crystallographically independent atoms of one particular CN occur in the asymmetric unit. A large number of independent interatomic distances are found in these complicated phases, varying from 20 in the a phase to 94 in the 6 phase. These distances show a large spread; they vary, for example, from 2.358 to 3.278A in the 6 phase. In our analysis of these distances we found that in each of these compounds every atomic position can be characterized by either one or two radii. The CN12 positions are characterized by a single radius, The higher coordinated positions are characterized by two radii, namely: the CN14 positions by 4 in the direction of the twelve "5-coordinated" ligands3 (called 'minor" by Frank and Kasperl) and by r:, in the direction of the two "6-coordi-nated" ligands (called "major" by Frank and Kasper); the CN15 positions by r15 for the twelve minor and r:, for the three major ligands; the CN16 positions by rlE for the twelve minor and r:, for the four major ligands. We have expressed the experimentally determined interatomic distances in observational equations as the sums of the appropriate pairs of these characteristic radii and the value of these radii have been determined by the method of least Squares. Despite their wide range, the interatomic distances could then be predicted by the sums of these atomic radii with an average deviation in any one compound of 0.06A or less. The results are summarized in Table I. Inspection of the radii thus obtained shows that in the structures in Table I the radii (in A) are given to a first approximation by the simple relationship: Where CN is the coordination number (12, 14, 15, or 16), and A = 1 for major ligands and = 0 for minor ligands. The interaLomic distances can be predicted within about 0.1A by sums of these atomic radii. Another phase belonging in this group with CN12, 14, 15, and 16 is the y phase & B7, in which A is molybdenum or tungsten and B is iron or cobalt. Recently the M%C phase has been refinedE and the observed distances also agree well with those calculated with Eq. [I]. (In the original determination of the structure of W6FeV7 the F$(II)-W(II1) distance was erroneously given as 2.84A, but we have recalculated it fro? the published parameters and found it to b? 2.57i4, in good agreement with the value of 2.6A predicted with Eq. [I.].) Many binary transition alloys are known to crystallize with the simpler structures having "nor-

Jan 1, 1964

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By Cyril Stanley Smith

The following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains tile results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). a Dr. Ing. Diss., Aachen, 1909. Quoted by Schenk: Ann. der Phys. (1910) 32, 261. b Beibl. Ann. der Phys. (1906) 29, 178. c Jnl. Inst. Metals (1928) 39, 375. d Jnl. Inst. Metals (192.5) 34, 43. e Ges. Abhand. Kennt. Kohle (1919) 4, 400. Experimental Methods Since the method of obtaining measurements of the thermal conductivity was identical with that described in the author's previous paper

Jan 1, 1931

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

Joseph HartshoRnE, Pottstown, Pa.: I have read Professor Akerman's valuable paper with great interest. Few of the present generation of American steel metallurgists are aware of the very important part taken by Swedish engineers in the successful development of the Bessemer proeess, and I am afraid some of the older ones have forgotten it. Certainly, I think, most of us would have said that Terre Noire was the first to introduce the use of metal direct from the blast-furnace. It is very well, therefore, that honor should be given to whom honor is due. I can speak from personal experience upon one part only of Prof. Akerman's paper; namely, the effect of the temperature at which the molten metal is cast upon the quality of the finished steel. In a general way I have, of course, known for a long time that the

Jan 1, 1894

By Sukune Takenouchi

Porphyry copper deposits in the southwestern Pacific region differ in some points of geologic features from those of the United States. The deposits distribute along old or active island arcs and are generally younger in age (1-16 m.y. B.P.). In Japan, however, no typical porphyry copper deposits are yet reported, though the geological situation of Japanese islands is similar to that of the southwestern Pacific. Fluid inclusions in some porphyry copper deposits In the southwestern Pacific region and those in igneous rocks genetically related to the ore deposits In Japan have been studied, and the genesis of ore-forming fluids from igneous rocks are discussed. From the results, the possibility of finding porphyry copper-type mineralization in Japan are considered.

Jan 1, 1976

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By J. V. Richards

The Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present gaper is to describe some of the more commoil Mexican dry-mashing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa, is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt.'' This ar-90 masa, occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted mas high.

Jan 1, 1911

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951